Page 2 - PrOPOSitiOn 65 warninG; Diesel engine exhaust and some of
page 2 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) PrOPOSitiOn 65 warninG Diesel engine exhaust and some of
Page 3 - You can also obtain information about motor vehicle safety from; rEPOrtinG SafEty DEfECtS
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 3 If you believe that your vehicle has a defect that could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifyin...
Page 4 - taBLE Of COntEntS; NOTICE; Component Drawings
page 4 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) taBLE Of COntEntS SG1400C3 Studio Generator Proposition 65 Warning ........................................... 2 Reporting Safety Defects ......................................... 3 Table Of Contents ..................
Page 5 - Ordering parts has never been easier!; Choose from three easy options:; WE ACCEPT ALL MAJOR CREDIT CARDS!; Order via Internet; Order; Order via Fax; PartS OrDErinG PrOCEDurES
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 5 www .multiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: ❒ Dealer Account Number ❒ Dealer Name and Address ❒ Shi...
Page 6 - SafEty infOrMatiOn; SaFeTY meSSageS; danger
page 6 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) SafEty infOrMatiOn Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safet...
Page 7 - general SaFeTY; generaTor SaFeTY
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 7 SafEty infOrMatiOn general SaFeTY CauTion never operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective de...
Page 8 - engine SaFeTY
page 8 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) SafEty infOrMatiOn engine SaFeTY danger The engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. The engine of this equipment requires ...
Page 9 - Fuel SaFeTY; ToWing SaFeTY; Safety Towing Regulations,
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 9 SafEty infOrMatiOn Fuel SaFeTY danger do noT start the engine near spilled fuel or combustible fl uids. Diesel fuel is extremely fl ammable and its vapors can cause an explosion if ignited. alWaYS refuel in a we...
Page 10 - eleCTriCal SaFeTY; power Cord/Cable Safety; grounding Safety
page 10 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) SafEty infOrMatiOn eleCTriCal SaFeTY danger do noT touch output terminals during operation. Contact with output terminals during operation can cause electrocution, electrical shock or burn. The electr ical volt...
Page 11 - BaTTerY SaFeTY; environmenTal SaFeTY
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 11 SafEty infOrMatiOn BaTTerY SaFeTY danger do noT drop the battery. There is a possibility that the battery will explode. do noT expose the battery to open fl ames, sparks, cigarettes, etc. The battery contains c...
Page 12 - SPECifiCatiOnS; Table 1. generator Specifications; open protected type synchronous generator; Table 2. engine Specifications; charge air cooled; Table 3. Battery Specifications
page 12 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) SPECifiCatiOnS Table 1. generator Specifications model SG1400C3 Type Revolving field, self ventilated, open protected type synchronous generator armature Connection 12-Lead WYE no of poles 4 prime output 200 kVA 1Ø...
Page 13 - DiMEnSiOnS
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 13 DiMEnSiOnS E F H G I D J TOP VIEW A B FRONT VIEW K L SIDE VIEW AC VO LTS AC AMPERES AC AMPERES M AC AMPERES HERTZ C Table 4. dimensions reference letter dimensions in. (mm) reference letter dimensions in. (mm) A 90...
Page 14 - inStaLLatiOn; Figure 2. Typical Generator Grounding Application
page 14 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) inStaLLatiOn GROUND ROD FOR EARTH GROUND GROUND CABLE GENERATOR GROUND LUG CONNECT TO BUILDING GROUND 8 FT. MINIMUM REFERENCE NEC 250-52(C) NOTE: GROUND LUG MUST BE INSTALLED BY USER. Figure 2. Typical Generator Gr...
Page 15 - ouTdoor inSTallaTion; CauTion; generaTor grounding; earTH; alWaYS
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 15 inStaLLatiOn ouTdoor inSTallaTion Install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift ar...
Page 16 - GEnEraL infOrMatiOn
page 16 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) GEnEraL infOrMatiOn generator The MQ Power Model SG1400C3 is a 200kVA studio generator that is designed as a high quality power source for entertainment and studio applications.In keeping with Multiquip's policy of...
Page 18 - intelivision 5; TM digital Controller
page 18 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) GEnEraL infOrMatiOn intelivision 5 ™ digital Controller The InteliVision 5 Digital Controller provides monitoring and fault detection capability of all engine and generator operating parameters. A list of operating...
Page 19 - nOtES
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 19 nOtES
Page 20 - GEnEratOr MaJOr COMPOnEntS; Figure 3. Major Components
page 20 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) 18 19 20 21 22 28 29 23 24 25 26 27 24 2 10 11 15 30 31 32 33 34 Inside Housing 17 4 6 3 1 5 7 14 16 8 9 12 13 GEnEratOr MaJOr COMPOnEntS Figure 3. Major Components
Page 22 - BaSiC EnGinE COMPOnEntS; Figure 4. Basic Engine Components; Table 6. Basic engine Components
page 22 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) BaSiC EnGinE COMPOnEntS Figure 4. Basic Engine Components Table 6. Basic engine Components iTem no. deSCripTion 1 Oil Filler Cap 2 Alternator 3 Oil Filter 4 Starter 5 Oil Drain Plug 6 Belt 7 Water Pump 8 Oil Dipsti...
Page 23 - BaSiC traiLEr COMPOnEntS; Figure 5. Basic Trailer Components
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 23 BaSiC traiLEr COMPOnEntS The definitions below describe the controls and functions of the Trailer (Figure 6).1. pintle eye Coupler — Adjustable 3-inch eye coupler rated at 20,000 lbs. (9,072 kg). 2. Hydraulic Brake...
Page 24 - COntrOL PanEL; Figure 6. Control Panel
page 24 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) COntrOL PanEL The definitions below describe the controls and functions of the Control Panel (Figure 6).1. voltage adjust Switch — To increase the output voltage, pull upward and hold the switch until the desired v...
Page 25 - CaMLOk/vOLtaGE OutPut PanEL
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 25 CaMLOk/vOLtaGE OutPut PanEL The definitions below describe the controls and functions of the Camlok/Voltage Output Panel (Figure 7).1. CB4/CB5 Circuit Breakers — These circuit breakers protect the 120 VAC auxiliary...
Page 26 - CirCuit BrEakEr PanEL; CB2 Circuit Breaker; Figure 8. Main Breaker Panel; DO NOT
page 26 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) Electronic Trip Unit Instantaneous Trip Setting - Amps Push to Trip Test Status A — 500 B — 600 C — 800 D — 1000 E — 1250 F — 1500 G — 2000 H — 2500 E D C B A H G F 450 AMP LONG — INST. Electronic Trip Unit Instant...
Page 27 - DiGitaL COntrOLLEr; navigaTionS BuTTonS; Figure 9. Digital Controller
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 27 DiGitaL COntrOLLEr Refer to Figure 9 for location of controls and indicators.1. STaTuS led — Indicates status of the controller. Lights green when the controller is running. navigaTionS BuTTonS 2. arroW up Button —...
Page 28 - LOaD aPPLiCatiOn/GEnEratOr OutPut; Single pHaSe load; Table 7. power Factor By load; THree pHaSe load
page 28 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) LOaD aPPLiCatiOn/GEnEratOr OutPut Single pHaSe load Always be sure to check the nameplate on the generator and equipment to insure the wattage, amperage, frequency, and voltage requirements are satisfactorily suppl...
Page 29 - GEnEratOr OutPutS; generaTor ouTpuT volTageS; Figure 10. Voltage Selector Switch; Table 9. voltages available; generator amperage; Table 10. generator maximum amps
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 29 GEnEratOr OutPutS generaTor ouTpuT volTageS A wide range of voltages are available to supply voltage for many different applications. Voltages are selected by using the voltage selector switch (Figure 10). To obtai...
Page 30 - Figure 11. Engine Oil Dipstick; Table 11. recommended motor oil; Fuel CHeCK
page 30 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) inSPECtiOn/SEtuP main CirCuiT BreaKer The generator is equipped with a 3-pole, 600-amp circuit breaker to protect the camlok receptacles from overload. Make sure that the main circuit breaker is in the oFF position...
Page 31 - do noT; DO NOT; fill on; onlY; Figure 14. Full Fuel Tank; Heat Source; EXPANDS; when heated
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 31 inSPECtiOn/SEtuP 1. Place the generator level with the ground. Failure to do so will cause fuel to spill from the tank before reaching full capacity (Figure 12). Figure 12. Only Fill on Level Ground 2. Remove fuel ...
Page 32 - operaTion in Freezing WeaTHer; Table 12. Coolant Capacity; Cleaning THe radiaTor; Figure 16. Drive Belt Inspection
page 32 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) inSPECtiOn/SEtuP CoolanT (anTiFreeze/Summer CoolanT) Cummins recommends antifreeze/summer coolant, for use in their engines, which can be purchased in concentrate (and mixed with 50% demineralized water) or pre-dil...
Page 33 - Figure 17. Battery Connections; alTernaTor
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 33 inSPECtiOn/SEtuP BaTTerY This unit is of negative ground. do noT connect in reverse. Always maintain battery fluid level between the specified marks. do noT over fill. Battery life will be shortened if the fluid le...
Page 34 - StartuP; BeFore STarTing; Figure 19. Voltage Selector Switch; LIGHTS IF; on
page 34 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) StartuP BeFore STarTing 1. Place the Control Power switch (Figure 18) on the digital control panel in the up position (ON). Figure 18. Control Power Switch (ON) 2. Place the voltage selector switch (Figure 19) in t...
Page 35 - Figure 26. START Button; PRESS MODE BUTTON; STarT; Figure 28. Bus Hot Light; STarT; PRESS GCB CONTROL BUTTON; BUS HOT
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 35 StartuP 6. If unit is to be used in parallel with another unit, interconnect the units. Interconnect the output buses with suitable power cables to carry full load capacity. Special male-to-male Camlok cables will ...
Page 36 - CloSing THe enCloSure doorS; Figure 29. Engine Enclosure Doors; normal SHuTdoWn proCedure; Figure 31. STOP Button; emergenCY SHuTdoWn proCedure; PRESS BUTTON
page 36 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) 9. If paralleling to another unit and the bus was already energized from another unit (BUS HOT light already on), pressing to close GCB button once would initiate a synchronizing mode. The light above the button wi...
Page 37 - PrOtECtivE DEviCES; proTeCTive deviCeS; oFF
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 37 PrOtECtivE DEviCES proTeCTive deviCeS Protection devices and emergency stop devices are designed as standard components for protection of the generator against trouble during operation. The LCD on the Digital Contr...
Page 38 - MaintEnanCE; Table 14. engine maintenance Schedule
page 38 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) MaintEnanCE Use Table 14 as a general maintenance guideline when servicing your engine. For more detail engine maintenance information, refer to the engine owner’s manual supplied with your engine. Table 14. engine...
Page 39 - Figure 34. Fuel Tank Cleaning
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 39 If the engine is operating in very dusty or dry grass conditions, a clogged air cleaner will result. This can lead to a loss of power, excessive carbon buildup in the combustion chamber and high fuel consumption. C...
Page 41 - Figure 35. Hydraulic Brake Components; HYdrauliC BraKe aCTuaTor; Figure 36. Hydraulic Brake Actuator
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 41 The following trailer maintenance guidelines are intended to assist the operator in preventive maintenance. Trailer BraKeS Properly functioning brake shoes and drums are essential to ensure safety. The brakes shoul...
Page 42 - adJuSTaBle CHannel; Warning; Table 15. Hydraulic Brake Troubleshooting; never; bolt length; Figure 37. Adjustable Channel; WHeel BearingS; Figure 38. Wheel Hub Components
page 42 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) Periodically check the actuator mounting fasteners for damage or loosening. Inspect the actuator for worn or damaged parts. As you are towing your trailer, be aware of any changes in braking quality. This could be ...
Page 43 - WHeel HuB adJuSTmenT; leaF SuSpenSion; Figure 39. Leaf Suspension Components
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 43 MaintEnanCE After removing the dust cap, cotter pin, spindle nut and spindle washer, remove the hub to inspect the bearings for wear and damage. Replace bearings that have flat spots on rollers, broken roller c...
Page 46 - Troubleshooting (intelivision 5 Controller)
page 46 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) trOuBLEShOOtinG (COntrOLLEr) Troubleshooting (intelivision 5 Controller) Symptom possible problem Solution Wrong Display HW SW and HW mismatch? Correct firmware has to be programmed. Invalidate configuration table ...
Page 47 - traiLEr GuiDELinES; Common CauSeS For loSS oF Trailer; do noT
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 47 traiLEr GuiDELinES The following guidelines are intended to assist the operator in the operation and handling of a trailer.Safety precautions should be followed at all times when operating a trailer. Failure to rea...
Page 49 - Trailer vin Tag; Figure A. Vehicle VIN Tag
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 49 inoperaBle BraKeS, ligHTS or mirrorS Be sure that the brakes and all of the lights on your trailer are functioning properly before towing your trailer. Check the trailer taillights by turning on your tow vehicle he...
Page 50 - Figure B. VIN Tag Location; gaWr; VIN TAG
page 50 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) Figure B. VIN Tag Location The trailer VIN Tag contains the following critical safety information for the use of your trailer. gaWr : The maximum gross weight that an axle cansupport. It is the lowest of axle, whee...
Page 51 - Figure C. Ball Hitch Coupler
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 51 emergenCY FlareS and Triangle reFleCTorS It is wise to carry these warning devices even if you are not towing a trailer. It is particularly important to have these when towing a trailer because the hazard fl ashers...
Page 52 - Coupling the Trailer to the Tow vehicle (Ball Coupler); Figure D. Ball Hitch Coupling Mechanism
page 52 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) or is worn, the trailer can come loose from the tow vehicle and may cause death or serious injury.THE TOW VEHICLE, HITCH AND BALL MUST HAVE A RATED TOWING CAPACITY EQUAL TO OR GREATER THAN THE TRAILER gross vehicle...
Page 53 - attaching Safety Chain; Breakaway Brake System; Figure F. Breakaway Brake System; Breakaway Cable Surge Brake System; Hydraulic Actuator
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 53 If the coupler cannot be secured to the hitch ball, do not tow the trailer. Call your dealer for assistance. Lower the trailer so that its entire tongue weight is held by the hitch and continue retracting the jack ...
Page 54 - pinTle HiTCH Coupler; Figure G. Pintle Hitch Coupler; pintle Coupler and pintle Hook
page 54 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) Connecting Trailer lights Connect the trailer lights to the tow vehicle’s electrical system using the electric connectors at the front of the trailer (tongue). Refer to the wiring diagram shown in the trailer wirin...
Page 55 - Coupling Trailer to Tow vehicle (pintle Coupler)
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 55 the ball andcoupler system. All bent or broken coupler parts must be replaced before towing the trailer.THE TOW VEHICLE, PINTLE HITCH AND PINTLE COUPLER MUST HAVE A RATED TOWING CAPACITY EQUAL TO OR GREATER THAN TH...
Page 56 - determining load limit of Trailer
page 56 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) Tire SaFeTY unsafe Tires, lug nuts or Wheels Trailer tires and wheels are more likely to fail than car tires and wheels because they carry a heavier load. Therefore, it is essential to inspect the trailer tires bef...
Page 57 - Figure I. Trailer Tire Placard; determining load limit of Tow vehicle
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 57 There is a vehicle placard (Figure I) located in the same location as the certifi cation label described above. This placard provides tire and loading information. In addition, this placard will show a statement re...
Page 58 - Tire FundamenTalS; Figure J. Standard Tire Sidewall Information; Note; Table a. Speed rating
page 58 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) Use the information contained in this section to make tire safety a regular part of your vehicle maintenance routine. Recognize that the time you spend is minimal compared with the inconvenience and safety conseque...
Page 59 - uniform Tire Quality grading Standards (uTQgS); Treadwear number; Figure K. UTQGS Tire Information; ST; Tire Safety Tips; Tire repair
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 59 uniform Tire Quality grading Standards (uTQgS) Treadwear number : This number indicates the tire’s wear rate. The higher the treadwear number is, the longer it should take for the tread to wear down. For example, a...
Page 60 - Table B. Tire Wear Troubleshooting; lug nut Torque requirements; Figure L. Wheel Lug Nuts Tightening Sequence
page 60 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) Table B below will help pinpoint the causes and solutions of tire wear problems. Wheel rims If the trailer has been struck, or impacted, on or near the wheels, or if the trailer has struck a curb, inspect the rims ...
Page 61 - lights and Signals; Table C. Tire Torque requirements; Wheel Size; Figure M. Trailer to Tow Vehicle Wiring Diagram
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 61 lights and Signals Before each tow, check the trailer taillights, stoplights, turn signals and any clearance lights for proper operation. Table C. Tire Torque requirements Wheel Size First pass FT-lBS Second pass F...
Page 62 - hyDrauLiC hOSES SChEMatiC
page 62 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) hyDrauLiC hOSES SChEMatiC
Page 63 - MaintEnanCE PartS LOCatOr
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 63 MaintEnanCE PartS LOCatOr L K1 K L1 P1 J1 I H D G C B M M1 N1 X Z B1 D1 Z1 Y1 P2 S S2 T2 U2 R1 Q2 C2 B2 Z2 A3 J2 I2 O2 G2 X2 Y2 W1 U1 P V2 W2 V1 Q T B3 K2 O1 S1 T1 F1 Y A1 C1 E1 O F U E A N R H2 A2 G1 F2 E2 D2 W P ...
Page 64 - GEnEratOr wirinG DiaGraM
page 64 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) GEnEratOr wirinG DiaGraM X S GRY/RED 239 237 238 221 234 235 236 233 229 232 231 230 225 226 227 228 223 224 222 220 219 218 216 217 215 214 210 213 212 211 206 209 208 207 GRY/RED WHT 439 438 437 421 436 435 434 4...
Page 66 - ExPLanatiOn Of CODES in rEMarkS COLuMn; Sample parTS liST; remarKS Column
page 66 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) ExPLanatiOn Of CODES in rEMarkS COLuMn The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there a...
Page 67 - SuGGEStED SParE PartS; description
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 67 SuGGEStED SParE PartS Sg1400C3 WiTH CumminS QSB7-g5 dieSel engine 1 to 3 units Qty. p/n description 3............3937736 ................ CARTRIDGE, LUB OIL FILTER 3............4989106 FUEL FILTER, ENGINE 3...........
Page 69 - ASSY, STEP BAFFLE WITH INSULATION
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 69 hOuSinG (BaSE) aSSy. no. parT no. parT name QTY. remarKS 1 EE55742 HOUSING, 1400 STUDIO, SINGLE BUS DOOR 1 2 EE40474 BASE, 1400A STUDIO, 48" X 100" 1 3 INSULATION ..............................................
Page 73 - BUS BAR, GROUND TO NEUTRAL
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 73 CaMLOk aSSy. no. parT no. parT name QTY. remarKS 1 EE55746 PANEL, OUTPUT BUS, CAMLOK 1 2 EE6378 RECEPTACLE, PNL MTG, FEMALE BLACK 6 3 EE6381 RECEPTACLE, PNL MTG, FEMALE BLUE 6 4 EE6380 RECEPTACLE, PNL MTG, FEMALE R...
Page 75 - COVER, DIGITAL METER
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 75 COntrOL BOx aSSy. (PanEL) no. parT no. parT name QTY. remarKS 1 EE55750 PANEL, INSTR, INTELIVISION 5 1 2 EE6523 HINGE, CONTROL PNL MTG. 1 3 EE55753 INTELIVISION 5.7" DISPLAY 1 3A EE55754 INTELLIGEN NT, BASE BOX...
Page 79 - NUT PLATE, BASE ASSY
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 79 EnGinE/GEnEratOr MOuntinG aSSy. no. parT no. parT name QTY. remarKS 1 EE15831 ALTERNATOR, MARATHON, 431RSL4007 1 2 9518500 DRIVE DISC ASSY SAE #11.5 1 3 EE55740 ENGINE, CUMMINS QSB7-G5NRS, TPEM 1 4 EE41016 MOTOR MO...
Page 80 - raDiatOr/MuffLEr SuPPOrt
page 80 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) raDiatOr/MuffLEr SuPPOrt 24 25 19 20 17 20 17 17 7 13 15 18 15 15 14 17 23 21 15 15 17 15 13 14 9 15 14 1 3 8 25 14 4 2 5 15 14 12 15 18 14 14 11 18 6 15 10 10A 16 22
Page 81 - parT name; UNISTRUT CHANNEL, MFL SUPPORT
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 81 raDiatOr/MuffLEr SuPPOrt no. parT no. parT name QTY. remarKS 1 EE41013 SUPPORT, RADIATOR 1 2 EE25484 COVER, FAN, STEEL 1 3 EE41023 ASSY, ARC BAFFEL W/ INSULATION 1 4 EE41698 VENTURI RING, 30" REVERSE CONSTR. 1 ...
Page 83 - OVERFLOW BOTTLE, RAD COOLANT
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 83 raDiatOr/fan aSSy. no. parT no. parT name QTY. remarKS 1 EE41227 RADIATOR, ALUM 1 2 EE38918 OVERFLOW BOTTLE, RAD COOLANT 1 3 EE43735 BRACKET, OVERFLOW BOTTLE 1 4 EE41285 MNTG PLATE, CHARGE AIR COOLER 2 5 EE40443 CH...
Page 84 - raDiatOr PiPinG
page 84 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) raDiatOr PiPinG 23 18 16 6 17 7 22 11 26 3 10 8 13 14 24 25 11 9 11 19 1 4 20 21 15 12 24 5
Page 85 - UPPER WATER LINE
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 85 raDiatOr PiPinG no. parT no. parT name QTY. remarKS 1 EE54732 UPPER WATER LINE 1 2 EE54733 LOWER WATER LINE 1 3 EE16449 ELBOW, 2 1/2 X 90˚, RUBBER 1 4 EE24234 FILTER, COOLANT, SPIN-ON 1 5 EE11315 MNTG HEAD KIT, COO...
Page 86 - air fiLtEr hOSinG/PiPinG
page 86 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) air fiLtEr hOSinG/PiPinG
Page 87 - ELEMENT, AIR CLEANER
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 87 air fiLtEr hOSinG/PiPinG no. parT no. parT name QTY. remarKS 1 EE41139 AIR FILTER, 13" DONALDSON 1 2 P537876 ELEMENT, AIR CLEANER 1 3 EE24247 BAND, METAL A/C MNTG 13" 2 4 EE32335 HUMP HOSE, STR. RUBBER 5...
Page 91 - BRACKET, MTG SWITCH TO SADDLE BOX
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 91 SaDDLE BOx aSSy. no. parT no. parT name QTY. remarKS 1 B-528258 REGULATOR, VOLTAGE, DVR2000E 1 2 A-66377-45 CAPACITOR, 7.5 MFD 1 3 EE7330 DECAL, CAUTION, DO NOT SWITCH 1 4 EE55779 TRANSFORMER, 3 KVA 1 5 EE2767 SWIT...
Page 93 - PANEL, STARTER RELAY
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 93 EnGinE StartEr, rELay anD BattEry aSSy. no. parT no. parT name QTY. remarKS 1 EE55818 PANEL, STARTER RELAY 1 2 EE2923 RELAY, BOSCH 24V 2 3 EE2917 RELAY, STARTER SOLENOID 24V 1 4 EE10881 BREAKER, CIRCUIT, PUSHBUTTON...
Page 95 - BRACKET, FULL SEPARATOR/COOLANT FILTER 1
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 95 fuEL SyStEM aSSy. no. parT no. parT name QTY. remarKS 1 EE36703 FUEL-WATER SEPARATOR, RACOR 1 2 EE32580 BRACKET, FULL SEPARATOR/COOLANT FILTER 1 3 EE50144 PUMP, FUEL, STEWART WARNER, 24V 1 3A EE11227 FILTER, FUEL P...
Page 100 - EnGinE COMPOnEnt aSSy.
page 100 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) EnGinE COMPOnEnt aSSy. 18 24 23 20 17 19 13 11 6 7 10 8 5 9 17A 14 14A 15 15 15A 15A 16A 2 3 21 1 12 4 22 16
Page 103 - TEST FITTING, PRESSURE GAUGE
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 103 no. parT no. parT name QTY. remarKS 1 EE47423 MANIFOLD, HYD. ACTUATORS, 150 PSI 1 2 EE41126 TEST FITTING, PRESSURE GAUGE 1 3 EE41837 CONN, DIN, PROPORTIONAL, SOLENOID 1 4 EE47425 BRACKET, HYD. ACTUATOR MANIFOLD 1 ...
Page 107 - PROPORTIONAL RELIEF VALVE W/BODY, 3000PSI
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 107 no. parT no. parT name QTY. remarKS 26 EE42719 SPACER, 1/2"OD x 1/4"ID x 3/4" LG, ZINC PLT 2 27 EE55034 Z-BRACKET, HYD FILTER W/QSB7 1 28 WASHER (COMES WITH ENGINE) 2 29 NUT (COMES WITH ENGINE) 2 30 1/...
Page 109 - TEST FITTING, PRESSURE GUAGE
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 109 hyD. PuMP, COOLEr, fan MOtOr anD hOSE aSSy. no. parT no. parT name QTY. remarKS 1 3/4SAE100R4-46 HOSE, HYD. 3/4 x 46" TANK TO PUMP 1 2 6801-12-12-NWO ELBOW, 90° 3/4"MJ x 3/4"MAORB 1 3 6801-08-10-NWO EL...
Page 110 - CrankCaSE vEntiLatiOn aSSy.; TO DRAIN
page 110 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) CrankCaSE vEntiLatiOn aSSy. 1 5 4 4 6 6 7 7 8 8 3 3A 2 9 10 13 12 13 14 15 17 16 18 19 20 19 21 22 23 24 25 26 TO DRAIN TO CRANKCASE OIL TO ENGINE BLOCK
Page 113 - ACTUATOR, HYDR SURGE BRK 20K
Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) — page 113 no. parT no. parT name QTY. remarKS 1 EE36264 PINTLE, EYE, RING 3" 1 2 EE42617 CAP SCREW, HX. HD. GRD 8 2 3 EE35394 WASHER, FLAT ZINC PLT. 5/8" 4 4 EE42618 NUT, HX. NYLOCK-INSERT, GRD 8 2 5 EE55941 ACTUATO...
Page 114 - tErMS anD COnDitiOnS Of SaLE — PartS
page 114 — Sg1400C3 STudio generaTor • operaTion and parTS manual — rev. #1 (02/15/12) tErMS anD COnDitiOnS Of SaLE — PartS paYmenT TermS Terms of payment for parts are net 30 days. FreigHT poliCY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipment...
Page 116 - OPEratiOn anD PartS ManuaL; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; United StateS; Canada
OPEratiOn anD PartS ManuaL Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United StateS Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. Carson, CA 90746 Contact: [email protected] Tel. (800) 421-1244 Fax (800) 537-3927 80...