Page 2 - PROPOSITION 65 WARNING
PAGE 2 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) Engine exhaust and some of its constituents, and some dust created of California to cause cancer, birthdefects and other reproductive harm. by power sanding, sawing, grinding, drilling and other construction ac...
Page 3 - SILICOSIS WARNING; SILICOSIS/RESPIRATORY WARNINGS
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 3 Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, bri...
Page 4 - TABLE OF CONTENTS
PAGE 4 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) TABLE OF CONTENTS NOTE: Specification and part number are subject to change without notice. Proposition 65 Warning .......................................... 2 Silicosis/Respiratory Warnings ......................
Page 5 - PARTS ORDERING PROCEDURES; Ordering parts has never been easier!; Choose from three easy options:; Order via Internet; Order; Order via Fax
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 5 PARTS ORDERING PROCEDURES www .multiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: ❒ Dealer Account Number ...
Page 6 - This checklist will lists some of the minimum requirements; TRAINING CHECKLIST
PAGE 6 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) TRAINING CHECKLIST This checklist will lists some of the minimum requirements for machine maintenance and operation. Please feel free to detach it and make copies. Use this checklist whenever a new operator is ...
Page 7 - DAILY PRE-OPERATION CHECKLIST
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 7 DAILY PRE-OPERATION CHECKLIST COMMENTS: DAILY PRE-OPERATION CHECKLIST T S I L K C E H C N O I T A R E P O - E R P Y L I A D 1 .l e v e l li o e n i g n E 2 .l e v e l li o c il u a r d y H 3 .l e v e l t n a l ...
Page 8 - SAFETY INFORMATION; SAFETY MESSAGES; DANGER
PAGE 8 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) SAFETY INFORMATION Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the ...
Page 9 - GENERAL SAFETY
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 9 SAFETY INFORMATION GENERAL SAFETY CAUTION NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protecti...
Page 10 - TROWEL SAFETY; ENGINE SAFETY
PAGE 10 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) TROWEL SAFETY DANGER Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. The engine of this equipment requires an adequate free ...
Page 11 - FUEL SAFETY; BATTERY SAFETY
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 11 NOTICE NEVER run engine without an air filter or with a dirty air filter. Severe engine damage may occur. Service air filter frequently to prevent engine malfunction. NEVER tamper with the factory settings...
Page 12 - TRANSpORTING SAFETY; TOWING SAFETY; Safety Towing Regulations,
PAGE 12 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) TRANSpORTING SAFETY CAUTION NEVER allow any person or animal to stand underneath the equipment while lifting. Ride-on trowels are very heavy and awkward to move around. Use proper heavy lifting procedures ...
Page 13 - chock blocks; ENVIRONMENTAL SAFETY; DO NOT
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 13 Trailer should be adjusted to a level position at all times when towing. Raise and lock trailer wheel stand in up position when towing. Place chock blocks underneath wheel to prevent rolling while parked...
Page 14 - HTH — SPECIFICATIONS; normal; if; HEIGHT
PAGE 14 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — SPECIFICATIONS NOTE: 1. This value includes the seat height.2. Sound pressure is a weighted measure. Measured at the operators ear position while the ride-on trowel is operat- ing at full throttle on con...
Page 15 - HTH — GENERAL INFORMATION; spider assembly
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 15 HTH — GENERAL INFORMATION HTH RIDE-ON TROWEL FAMILIARIZATION The HTH series Ride-On Power Trowels are designed for the floating and finishing of concrete slabs.Take a walk around the HTH Ride-On Power Trowel. ...
Page 16 - HTH — CONTROLS AND INDICATORS
PAGE 16 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — CONTROLS AND INDICATORS 13. Radiator/Filler Cap – Holds coolant or water necessary to keep engine at a safe operating temperature. Remove this cap to add water or antifreeze. 14. Kill Switch - Shuts down...
Page 17 - Retardant Spray Motor –; Slabs on Grade
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 17 HTH — CONTROLS AND INDICATORS 27. Oil Filter – Provides oil filtering for the engine . 28. Retardant Spray Motor – Used with the spray control button. 29. Retardant Spray Tank - Holds 5 gallons of retardant or...
Page 18 - kill switch; CAUTION; HTH — INITIAL START-UP; Figure 4. Engine Oil Dipstick
PAGE 18 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) This section is intended to assist the operator with the initial start-up of the HTH series Ride-On Power Trowel. It is extremely important that this section be read carefully before attempting to use the trow...
Page 19 - LOW; charge; HIGH; Steering
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 19 HTH — INITIAL START-UP 3. It is recommended that the kill switch be used to stop the engine after every use. Doing this will verify that the switch is working properly and presents no danger to the operator. R...
Page 20 - Figure 12. Blade Speed Control Foot Pedal
PAGE 20 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — INITIAL START-UP Figure 12. Blade Speed Control Foot Pedal Figure 13. Joystick Control Forward Direction Figure 14. Joystick Control Reverse Direction g n i n o it i s o P l a n o it c e ri D k c it s y ...
Page 21 - HTH — MAINTENANCE; NOTE; replace the hydraulic; Left Spider Speed Adjustment
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 21 HTH — MAINTENANCE NOTE See the engine manual supplied with your machine for ap- propriate engine maintenance schedule and troubleshooting guide for problems.At the front of the book (Page B) there is a “Daily ...
Page 22 - Figure 16. Pump Actuation; Matching Blade Pitch for Both Sets of Blades
PAGE 22 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — MAINTENANCE Figure 16. Pump Actuation Levers/Speed Control Rod Figure 17. Blade Pitch Adjustment Bolt PUMP ACTUATION LEVERS ADJUSTMENT NUT HYDRAULIC PUMP Matching Blade Pitch for Both Sets of Blades Some...
Page 23 - Changing A Blade
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 23 HTH — MAINTENANCE Changing A Blade Whiteman recommends that all the blades on the entire ma- chine be changed at the same time. If only one or some of the blades are changed at one time, the machine will not f...
Page 24 - HTH — TROUBLESHOOTING
PAGE 24 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — TROUBLESHOOTING Troubleshooting (Ride-On Mechanical Trowel) Symptom Possible Problem Solution Engine running rough or not at all. Stop switch malfunction? Make sure that the stop switch is functioning wh...
Page 26 - Sample partS liSt; remarKS Column; EXPLANATION OF CODE IN REMARKS COLUMN
PAGE 26 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. Sample partS liS...
Page 27 - HTH — SUGGESTED SPARE PARTS; Part numbers on this Sug-
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 27 HTH — SUGGESTED SPARE PARTS 1 to 3 Units Qty. P/N Description 4............. 0183 ....................... COTTER PIN 6............. 10221 ..................... BUSHING 2............. 11648 .......................
Page 28 - HTH — LEFT/RIGHT PIVOT ASSY; RIGHT SIDE PIVOT ASSEMBLY
PAGE 28 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — LEFT/RIGHT PIVOT ASSY TORQUE TO 60 FT. LBS APPLY LOCTITE. SEE PAGE 44 FOR HYDRAULIC MOTOR HOSE CONNECTIONS. PLACE FLUSH HEAD SCREW IN BACK OF MOUNT AS SHOWN. PLACE HEX HEAD SCREW IN FRONT OF MOUNT AS SHO...
Page 31 - HTH — NOTE PAGE
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 31 HTH — NOTE PAGE
Page 32 - HTH — LEFT/RIGHT TWIN PITCH ASSY
PAGE 32 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — LEFT/RIGHT TWIN PITCH ASSY CONTINUED ON NEXT PAGESEE , ITEM 32. CONTINUED ON NEXT PAGESEE , ITEM 31. A B 60 66 67 62 62 63 64 65 1 2 2 2 1 2 2 25 57 3 6 23 29 59 58 37 15 38 2 10 4 9 28 34 33 36 29 5 1 3...
Page 34 - LEFT/RIGHT TWIN PITCH ASSY
PAGE 34 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — LEFT/RIGHT TWIN PITCH ASSY LEFT/RIGHT TWIN PITCH ASSY NO PART NO PART NAME QTY. REMARKS 1 + % 0126 B KEY, WOODRUFF #9 1 2 + % 0161C WASHER, LOCK 5/16 MED 3 3 * + % 0181 B WASHER, LOCK, 1/4 MED 1 4 + % 06...
Page 46 - HTH — HYDRAULIC STEERING ASSY
PAGE 46 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — HYDRAULIC STEERING ASSY
Page 47 - HYDRAULIC STEERING ASSY
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 47 HTH — HYDRAULIC STEERING ASSY HYDRAULIC STEERING ASSY NO PART NO PART NAME QTY. REMARKS 1 0161 C WASHER, LOCK, 5/16 MED 12 2 0300 B WASHER, FLAT, 5/16 SAE 16 3 0447 WASHER, FLAT, 1/2 SAE 2 4 10176 NUT, NYLOC 1...
Page 54 - HTH — HYDRAULIC DRIVE ASSY
PAGE 54 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — HYDRAULIC DRIVE ASSY
Page 56 - HYDRAULIC DRIVE ASSY
PAGE 56 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — HYDRAULIC DRIVE ASSY HYDRAULIC DRIVE ASSY NO PART NO PART NAME QTY. REMARKS 1 0166 A WASHER, LOCK, 3/8 MED 2 2 0300 B WASHER, FLAT, 5/16 SAE 4 3 0424 SCREW, HHC 1/4-20 X 1 1/4 1 4 0948 WASHER, FLAT, 1/4 ...
Page 68 - HTH — STABILIZER RING ASSY; STABILIZER RING ASSY
PAGE 68 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — STABILIZER RING ASSY STABILIZER RING ASSY
Page 78 - HTH — SEAT AND FRAME; SEAT AND FRAME
PAGE 78 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — SEAT AND FRAME 14 59 28 16 27 5 32 37 36 61 4 HYDRO-ST ATIC DRIVE SEAT AND FRAME
Page 80 - HTH — FRAME AND FUEL TANK; FRAME AND FUEL TANK
PAGE 80 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — FRAME AND FUEL TANK 44 59 52 65 52 42 43 21 46 41 57 64 57 57 7 * * * * 40 45 4 4 55 34 47 16 3 28 3 4 24 4 CONNECT TO FUEL PUMP SEE SHEET XX. STUD BOLT FOR FUEL TANK BRACKET IS WELDED TO FRAME FOR COMPL...
Page 82 - HTH — FOOT PEDALS; FOOT PEDALS
PAGE 82 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — FOOT PEDALS RIGHT FRONT PEDAL FOR PEDAL MOUNTING HARDWARE SEE DETAIL A, SHEET XX (VIEW FROM OPERATOR'S SEAT) C0NNECT TO HYDRAULIC PUMP SEE PAGE XX 23 22 51 27 29 30 54 51 27 48 32 9 9 18 19 60 11 33 11 6...
Page 84 - HTH — BATTERY; BATTERY
PAGE 84 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — BATTERY BA TTER Y RED CABLE STARTER BLACK CABLE POSITIVE NEGATIVE 39 53 10 37 36 15 49 13 56 62 63 38 12 26 50 1 5 14 15 8 8 17 25 61 58 35 2 6 7 7 6 9 7 20 7 FOR SPRAY ASSEMBLY PARTS BREAKDOWN SEE SHEET...
Page 85 - PART NO
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 85 HTH — BATTERY BATTERYNO PART NO PART NAME QTY. REMARKS 1 0161 C WASHER, LOCK, 5/16 MED 1 2 0181 B WASHER, LOCK, 1/4 MED 4 5 0479 WASHER, EXT SHKP, 3/8 PLTD 1 6 0730 SCREW, HHC 1/4 – 20 X 1 11 7 0948 WASHER, FL...
Page 86 - HTH — SPRAY ASSY; SPRAY ASSY
PAGE 86 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — SPRAY ASSY 3 22 16 8 24 21 4 23 1 5 1 2 19 7 20 5 25 19 1 6 5 1 11 2 2 5 14 10 26 12 19 9 13 12 5 4 17 15 18 20 27 4 PART OF ITEM 6 19 57” 2 8” 25 8” 2” SPRAY ASSY
Page 88 - HTH — LIGHT ASSY; LIGHT ASSY
PAGE 88 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — LIGHT ASSY LIGHT ASSY
Page 90 - HTH — E-Z MOVER AND LIFT HANDLE; E-Z MOVER AND LIFT HANDLE
PAGE 90 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) HTH — E-Z MOVER AND LIFT HANDLE E-Z MOVER AND LIFT HANDLE
Page 94 - TERMS AND CONDITIONS OF SALE — PARTS
PAGE 94 — HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All ship...
Page 95 - NOTE PAGE
HTH-8 FT. RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (02/22/11) — PAGE 95 NOTE PAGE
Page 96 - OperatiOn and parts Manual; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; UNITED STATES; CANADA
OperatiOn and parts Manual Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Offi ce MQ Parts Department 18910 Wilmington Ave. Carson, CA 90746 Contact: [email protected] Tel. (800) 421-1244 Fax (800) 537-3927 8...
