Page 2 - prOpOsitiOn 65 warning
page 2 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) prOpOsitiOn 65 warning
Page 3 - nOtes
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 3 nOtes
Page 4 - taBle Of COntents; MtX80sd rammer; Component drawings; NOTICE
page 4 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) taBle Of COntents MtX80sd rammer Proposition 65 Warning ........................................... 2 Parts Ordering Procedures ...................................... 5 Safety Information .........................................
Page 5 - parts Ordering prOCedures; Ordering parts has never been easier!; Choose from three easy options:; order via internet; Order; order via Fax
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 5 parts Ordering prOCedures www .multiquip .com Ordering parts has never been easier! Choose from three easy options: We aCCepT all MaJoR CReDiT CaRDS! when ordering parts, please supply: ❒ Dealer account number ❒ Dealer name an...
Page 6 - safety infOrMatiOn; SaFeTy MeSSageS; DangeR
page 6 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) safety infOrMatiOn Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages ...
Page 7 - geneRal SaFeTy; RaMMeR SaFeTy
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 7 safety infOrMatiOn geneRal SaFeTy CauTion neveR operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices requi...
Page 8 - engine SaFeTy; Fuel SaFeTy
page 8 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) safety infOrMatiOn engine SaFeTy DangeR The engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. The engine of this equipment requires an adequate...
Page 9 - TRanSpoRTing SaFeTy; enviRonMenTal SaFeTy
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 9 safety infOrMatiOn TRanSpoRTing SaFeTy CauTion NEvER allow any person or animal to stand underneath the equipment while lifting. NOTICE Before lifting, make sure that the equipment parts (hook and vibration insulator) are ...
Page 10 - speCifiCatiOns; Table 1. Rammer Specifications
page 10 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) speCifiCatiOns Table 1. Rammer Specifications Overall Height 39.37 in. (1000 mm) Overall Width 13.89 in. (353 mm) Over Length 30.78 in. (782 mm) Shoe Size (W x L) 13.4 x 11.2 in. (340 x 285 mm) Fuel Tank Capacity 2.7 qt. (2.5...
Page 11 - general infOrMatiOn; CauTion
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 11 general infOrMatiOn The Multiquip MTX80SD tamping rammer is a powerful compacting tool capable of applying a tremendous force in consecutive impacts to a soil surface. Its applications include soil compacting for road, embank...
Page 12 - COMpOnents; Figure 1. MTX80SD Rammer; GRIP
page 12 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) COMpOnents Figure 1. MTX80SD Rammer 2 1 9 3 4 5 6 7 10 11 12 13 8 Figure 1 shows the location of the controls and components for the MTX80SD Tamping Rammer. The functions of each control is described below:1. Combination (Thr...
Page 13 - BasiC engine
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 13 BasiC engine Figure 2. Robin ER120D45000 Engine The engine (Figure 2) must be checked for proper lubri- cation and filled with fuel prior to operation. Refer to the engine manufacturer's manual for detailed operation and serv...
Page 14 - inspeCtiOn; Do noT use; CRankCaSe anD SpRing CylinDeR oil BaTH; Figure 3. Foot Housing Sight Glass; engine; Figure 5. Engine Oil Dipstick; geneRal inSpeCTion; Table 3. Motor oil grade
page 14 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) inspeCtiOn It is extremely important that this section be read carefully before attempting to operate the rammer. Do noT use your rammer until this section is thoroughly understood. CRankCaSe anD SpRing CylinDeR oil BaTH This...
Page 15 - OperatiOn; iniTial STaRTup; Figure 8. Choke Lever
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 15 OperatiOn iniTial STaRTup When starting the MTX80SD Tamping Rammer perform the following:1. Slide the throttle lever from the stop to the idle position ( ) (Figure 6). This opens the fuel cock and the engine electrical circui...
Page 16 - opeRaTion; quickly; Do noT move the throttle lever slowly as this; STopping THe engine; STaRT to iDle; cools
page 16 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) OperatiOn opeRaTion 1. To start the rammer tamping action, move the throttle lever (Figure 10) quickly from iDle to the STaRT ( ) position. Do noT move the throttle lever slowly as this may cause damage to the clutch or sprin...
Page 17 - MaintenanCe; Daily; Figure 13. Air Cleaner Primary Element; Figure 14. Oil Drain Plug; eveRy 6 MonTHS; Figure 15. Fuel Strainer; eveRy 2 yeaRS
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 17 MaintenanCe Daily Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the spring box and bellows...
Page 18 - trOuBleshOOting
page 18 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) trOuBleshOOting Troubleshooting (engine) Symptom possible problem Solution Diffi cult to start, fuel is available, but no spark at spark plug. Combo lever in incorrect position? Make sure combo lever is in start position. Spa...
Page 22 - eXplanatiOn Of COde in reMarks COluMn; SaMple paRTS liST; ReMaRkS Column
page 22 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) eXplanatiOn Of COde in reMarks COluMn The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any quest...
Page 23 - suggested spare parts; Description
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 23 suggested spare parts NOTICE Part numbers on this Suggested Spare Parts list may supersede/replace the part numbers shown in the following parts lists. MTX80SD TaMping RaMMeR WiTH RoBin eR120D4500 engine 1 to 3 units Qty. p/n...
Page 24 - naMeplates and deCals
page 24 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) naMeplates and deCals 11 1 2 10 9 3 5 6 7 4 8 A (DECAL SET) Gasoline Only (< Essence Uniquement Bitte nur Benzin elnfullen Usare solo Benzina Solo para Gasoline =E10) series quick manual Operation of this equipment may cre...
Page 25 - paRT naMe; DECAL: LEvER OPERATION
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 25 naMeplates and deCals no. paRT no. paRT naMe QTy. ReMaRkS 1 920215440 DECAL: OPERATION 1 2# DECAL: AIR CLEANER 1 3# DECAL: LEvER OPERATION 1 4# DECAL: MAX SPEED 1 5# DECAL: MACHINE STOP 1 6# DECAL: EC NOISE REQ Lwa 107 dB 1 7...
Page 27 - CrankCase and engine assy
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 27 CrankCase and engine assy no. paRT no. paRT naMe QTy. ReMaRkS 1 366910010 CRANKCASE ....................................................1................INCLUDES ITEMS W/$ 2$ 009120204 STUD BOLT 10 X 30 2 3 041006007 BEARING ...
Page 31 - guide Cylinder assy
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 31 guide Cylinder assy no. paRT no. paRT naMe QTy. ReMaRkS 1 366460100 PISTON PIN 1 2 366459910 PLUG, PISTON PIN 2 3 366346000 PISTON ROD 1 4 371459690 PISTON END 1 5-1 001121230 BOLT 12X30 T P1.5 1 5-2 030212300 WASHER, LOCK M1...
Page 32 - fOOt assy
page 32 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) fOOt assy 2 3 2 3 6 1 5 15 14 4 8 9 8 9
Page 33 - NYLON NUT M12
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 33 fOOt assy no. paRT no. paRT naMe QTy. ReMaRkS 1 8511S FOOT ASSY 285 ...............................................1................INCLUDES ITEMS W/ # 2 0227-11214 NYLON NUT M12 4 3 030212300 WASHER, LOCK M12 4 4 009110034 B...
Page 34 - fuel tank and handle assy
page 34 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) fuel tank and handle assy 3 1 4-2 4-1 7 6 5 41 41 43 43 42 42 9 10 23 54 51 22 53 14 15 56 2-1 2-2 11 11-1 11-2 11-3 11 55 4-2 4-1 12 12 13 20 19 20 A 102 102 102 102 104 101 106 105 B 113 112 112 111 40 11 18 17 16 A B 57 58...
Page 36 - COMBinatiOn leVer assy
page 36 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) COMBinatiOn leVer assy 11 12 13 14 2 4 6 9 7 7 8 5 A 1 11 10 3 BODY B
Page 38 - tOOls; TOOLS
page 38 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) tOOls PAGE 38 — MTX80SD RAMMER — OPERATION AND PARTS MANUAL — REV. #1 (02/01/12) TOOLS
Page 40 - GASKET SET
page 40 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) rOBin er120d45000 engine — CrankCase assy. GASKET SET 280 285 301 10 26 30 40 50 60 70 75 80 85 90 113 114 115 117 210 952 230 940 941 942 948 250 260 268 953 954 300 610 620 630 680 690 700 710 810 820 830 840 860 960 675 34...
Page 49 - BOLT AND WASHER ASSY
MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) — page 49 rOBin er120d45000 engine — COOling assy. no. paRT no. paRT naMe QTy. ReMaRkS 40 X130060340 BOLT AND WASHER ASSY 4 90 21E52601H3 CYLINDER BAFFLE 1 95 20F0060010 FLANGE BOLT 3
Page 56 - terMs and COnditiOns Of sale — parts
page 56 — MTX80SD RaMMeR • opeRaTion anD paRTS Manual — Rev. #0 (07/20/12) terMs and COnditiOns Of sale — parts payMenT TeRMS Terms of payment for parts are net 30 days. FReigHT poliCy All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B....
Page 58 - OperatiOn and parts Manual; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAvE THE MODEL AND SERIAL; Canada
OperatiOn and parts Manual Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAvE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United StateS Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. Carson, CA 90746 Contact: [email protected] Tel. (800) 421-1244 Fax (310) 537-3927 80...
