Page 2 - TABLE OF CONTENTS; COMPONENT DRAWINGS; Specification and part number are
PAGE 2 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) TABLE OF CONTENTS HBC19A/HBC25A REBARCUTTER Table of Contents .................................................... 2Parts Ordering Procedures ..................................... 3Safety .............................
Page 3 - PARTS ORDERING PROCEDURES; Ordering parts has never been easier!; Choose from three easy options:; Order via Internet; Order; Order via Fax
HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) — PAGE 3 PARTS ORDERING PROCEDURES www .multiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: R Dealer Account Number R De...
Page 4 - DANGER; SAFETY
PAGE 4 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) FOR YOUR SAFETY AND SAFETY OF OTHERS! Safety precautions should be followed at alltimes when operating this equipment. Fail-ure to read and understand the Safety Mes-sages and Operating Instructions could resultin ...
Page 5 - RULES AND REGULATIONS; GENERAL SAFETY; WARNING — Read This Manual; DEATH; ! This equipment is to be; EMERGENCIES
HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) — PAGE 5 DO NOT wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from movingparts. Rotating parts can cause injury if contacted. ALWAYS keep work area clean and free of foreign mat...
Page 7 - SPECIFICATIONS; li
HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) — PAGE 7 SPECIFICATIONS s n o i t a c i f i c e p S . 1 e l b a T l e d o M A 9 1 C B H A 5 2 C B H y t i c a p a C g n i t t u C m u m i x a M ) 0 4 ( e d a r G e t a i d e m r e t n I m m / g k 5 4 ( i s p 0 0 0 , 0 7 2 )...
Page 8 - GENERAL INFORMATION; The; MQ HBC19A/HBC25A Rebar Cutter; is designed to
PAGE 8 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) GENERAL INFORMATION GENERAL INFORMATION The MQ HBC19A/HBC25A Rebar Cutter is designed to be used as a portable on-site rebar cutter, capable of cut- ting in-place rebar safely and efficiently with the squeezeof a t...
Page 9 - COMPONENTS
HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) — PAGE 9 COMPONENTS Figure 1. HBC19A/HBC25A Components Figure 1 shows the components of the HBC19A/HBC25ARebar Cutter. These components are described below. 1. Blade (set of two) - Cuts the rebar that is set on the holder b...
Page 10 - OPERATION; CUTTING PROCEDURE; Figure 2. Rebar Placement; RETURN VALVE OPERATION
PAGE 10 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) OPERATION CUTTING PROCEDURE 1. Adjust the spacing bolt according to the diameter of the rebar being cut. Bolt must allow rebar to be flush,at 90° to the blades. 2. Connect the electric plug from the cutter to a pr...
Page 11 - REPLACING CARBON BRUSHES; Figure 3. Return Valve
HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) — PAGE 11 REPLACING CARBON BRUSHES When the carbon becomes less than 5 or 6 mm (1/4 inch)the motor force deteriorates because of low rectification(Figure 4). The carbon brushes need to be replaced at thistime. It is also re...
Page 12 - REPLACING OIL; REMOVE; MAINTENANCE; Figure 7. Removing Oil Fill Bolt; FILL WITH OIL
PAGE 12 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) REPLACING OIL The rebar cutter uses hydraulic action to operate. If thereis insufficient, dirty, or improper oil in the cutter, it will notoperate at full capacity. If unit is not operating properly,check oil leve...
Page 14 - EXPLANATION OF CODE IN REMARKS COLUMN; SAMPLE PARTS LIST; REMARKS Column
PAGE 14 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there a...
Page 15 - SUGGESTED SPARE PARTS
HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) — PAGE 15 SUGGESTED SPARE PARTS HBC19A/25A REBAR CUTTER 1 to 3 Units Qty. P/N Description 2 6415710 ............ BRUSH CAP (FOR HBC19A) 2 6402520 ............ BRUSH CAP (FOR HBC25A) 2 6415730 ............ CARBON BRUSH (FOR ...
Page 16 - HBC19A/HBC25A — NAMEPLATE AND DECALS
PAGE 16 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) HBC19A/HBC25A — NAMEPLATE AND DECALS 1 5 HBC19A OPERATING INSTRUCTIONS 1. Place rebar in rebar holder. Rebar must rest fully within the blades. 2 Adjust spacing bolt so it holds rebar flush against stationary cutt...
Page 17 - PART NAME; SAFETY WARNING DECAL
HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) — PAGE 17 HBC19A/HBC25A — NAMEPLATE AND DECALS NO. PART NO. PART NAME QTY. REMARKS 1 8006660 SAFETY WARNING DECAL 1 2 8006670 OPERATING INSTRUCTIONS DECAL 1 3 8006680 MQ LOGO 1 4 NAMEPLATE .....................................
Page 18 - HBC19A — REBAR CUTTER ASSEMBLY
PAGE 18 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) HBC19A — REBAR CUTTER ASSEMBLY 1 2 2 3 3 4 5 9 8 84 7 6 10 11 12 9 14 15 15 14 16 17 18 19 20 21 22 24 23 25 26 26 27 27 29 2 3 30 34 32 31 35 36 37 38 40 39 41 43 42 44 45 46 46 46 47 48 49 49 49 50 50 50 51 51 5...
Page 22 - HBC25A — REBAR CUTTER ASSEMBLY
PAGE 22 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) HBC25A — REBAR CUTTER ASSEMBLY 50 51 52 52 52 51 51 53 53 53 54 54 54 55 55 55 56 56 56 49 48 48 48 47 45 46 44 44 43 1 37 39 38 36 2 2 3 3 4 5 6 7 8 9 11 10 12 13 9 15 15 16 17 19 18 20 21 89 88 87 24 25 70 26 29...
Page 26 - ALLEN
PAGE 26 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) HBC19A/HBC25A — TOOLS 17 MM 19 MM HYDRAULIC OIL ALLEN WRENCHES 3 MM 4 MM 5 MM 6 MM ALLEN WRENCHES 6 MM 8 MM 4 MM 5 MM 14 MM 17 MM 24 MM 1 2 8 7 6 3 4 5
Page 28 - HBC19A/HBC25A — WIRING DIAGRAM
PAGE 28 — HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) HBC19A/HBC25A — WIRING DIAGRAM 120V 120V 60 Hz 60 Hz BLACK BLUE BLACK BLUE STATOR STATOR BRUSHES BRUSHES ARMATURE ARMATURE ON/OFF SW ON/OFF SW HBC25A HBC19A WHITE WHITE BLACK BLACK
Page 29 - TERMS AND CONDITIONS OF SALE — PARTS
HBC19A/HBC25A REBAR CUTTER • OPERATION AND PARTS MANUAL — REV. #4 (03/30/09) — PAGE 29 TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipment...
Page 30 - OPERATION AND PARTS MANUAL; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; UNITED STATES; CANADA
OPERATION AND PARTS MANUAL Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING © COPYRIGHT 2009, MULTIQUIP INC. Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written ...
