Multiquip EM-900SD - Manual

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 5 Accidental Starting EM-900SDCE MIXER — SAFETY MESSAGE ALERT SYMBOLS ALWAYS make sure the engine is turned OFF before servicing the engine or equipment. Respiratory Hazard A LWAY S we a r a p p r o ve d r e s p i r a t o ...

PAGE 6 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) EM-900SDCE MIXER — OPERATION AND SAFETY DECALS Machine Safety Decals The Multiquip EM-900SDCE mixer is equipped with a number of safety decals (see below and on the proceeding page). Thesedecals are provided for operator...

PAGE 8 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) EM-900SDCE MIXER — SPECIFICATIONS (NOISE AND VIBRATION) EC Declaration of Conformity In accordance with EN 45014:1998 We Multiquip Inc. of 18910 Wilmington Avenue, Carson, California 90746 declare that: Equipment Concret...

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 9 EM-900SDCE MIXER — SPECIFICATIONS In accordance with our established policy of constantimprovement, we reserve the right to amend thesespecifications at any time without notice. NOTE s n o i t a c i f i c e p S r e x i M...

PAGE 10 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) The following safety guidelines should always be used whenoperating the EM-900SD CE mixer: GENERAL SAFETY ■ DO NOT operate or service this equipment before reading this entire manual. ■ This equipment should not be oper...

PAGE 12 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) EM-900SDCE MIXER — GENERAL INFORMATION GENERAL Multiquip's EM-900SD CE series plaster and mortar mixer isshipped completely assembled and has been factory tested. The drum batch capacity of this mixer is between 6 and 7...

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 13 EM-900SDCE MIXER — ENGINE COMPONENTS INITIAL SERVICING The engine (Figure 1) must be checked for proper lubrication andfilled with fuel prior to operation. Refer to the manufacturers Enginemanual for instructions & ...

PAGE 14 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) 1. Engine Cover — Lift this cover to gain access to the engine compartment. 2. Clutch Engagement Lever — Push the clutch lever forward, toward the tow end of the mixer to engage clutch.Once the clutch is engaged the pad...

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 15 EM-900SDCE MIXER — PADDLE BLADE ADJUSTMENT B Figure 3 illustrates the paddle blade adjustment ( steel drum ). Figure 3. Paddle Blade Adjustment, Steel Drum

PAGE 16 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) FUEL 1. Lift the fuel cap latch (Figure 1) located ontop of the fuel tank, then look inside the tankand determine if the engine fuel is low . If fuelis low, fill with diesel fuel (Figure 4). EM-900SDCE MIXER — INSPECTIO...

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 19 EM-900SDCE MIXER — MAINTENANCE The clutch reduction assembly has two separate compartments.Each of which must be filled with its proper lubricant and checkedat regular intervals. The clutch compartment should be filled ...

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 23 NOTE PAGE

PAGE 24 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) EXPLANATION OF CODE IN REMARKS COLUMN The contents and part numbers listed in the parts section aresubject to change without notice . Multiquip does not guarantee the availibility of the parts listed. When ordering a pa...

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 25 EM-900SDCE MIXER — SUGGESTED SPARE PARTS EM-900SDCE 1 TO 3 UNITS Qty. P/N Description 6 ............ 491010 ............ RUBBER LATCH ASSY.1 ............ EM200293 ...... PADDLE ARM TOW SIDE1 ............ EM200294 .........

PAGE 26 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) EM-900SDCE MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 27 EM-900SDCE — NAME PLATE AND DECALS NAME PLATE AND DECALS NO PART NO PART NAME QTY. REMARKS 1 DCL212 DECAL: FORKLIFT (LEFT) 1 2 DCL213 DECAL: FORKLIFT (RIGHT) 1 3 DCL280 DECAL: WARNING, STAND CLEAR OF DUMP HANDLE 1 4 513...

PAGE 30 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) EM-900SDCE MIXER — MIXING DRUM ASSEMBLY MIXING DRUM ASSY.

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 31 MIXING DRUM ASSY. NO PART NO PART NAME QTY. REMARKS 1 512990 PADDLE SHAFT 1 2 EM963610 SCREW, HHCS 3/8 "NC X 1-1/4" G5 ................... 6 ......... REPLACES P/N 492375 3 EM201537 HANDLE, DUMP 1 4 6109160 NUT,...

PAGE 32 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) PADDLE SHAFT ASSEMBLY EM-900SDCE MIXER — PADDLE SHAFT ASSEMBLY

MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) — PAGE 33 EM-900SDCE MIXER — PADDLE SHAFT ASSEMBLY ASSEMBLY PADDLE SHAFT ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 512990 PADDLE SHAFT 1 2 492584 NUT, LOCK 1/2" 6 3 EM200295 PADDLE CAST, CENTER ENGINE END 1 4 510721 B0LT, 1...

PAGE 42 — MULTIQUIP EM-900SDCE — OPERATION AND PARTS MANUAL — REV. #2 (09/14/07) PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect orprepaid with the charges added to the invoice.All shipments are F.O.B. point of origin.Multiquip’s resp...

^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668 OPERATION AND PARTS MANUAL Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING © COPYRIGHT 2007, MULTIQUIP INC. Multiquip Inc, the MQ logo and the Essick logo are registered trademarks of Multiquip Inc. and m...