Multiquip CDM1H - Manual - manualsarea.com

Page 2 - CDM1H HAND-HELD CORE DRILL — PROPOSITION 65 WARNING

PAGE 2 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) Engine exhaust and some of its constituents, and some dust created of California to cause cancer, birthdefects and other reproductive harm. by power sanding, sawing, grinding, drilling and other construction activities contai...

Page 3 - SILICOSIS WARNING; CDM1H HAND-HELD CORE DRILL — SILICOSIS WARNING

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 3 Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, brick clay, grani...

Page 4 - CDM1H HAND-HELD CORE DRILL — TABLE OF CONTENTS; Specification and part number

PAGE 4 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — TABLE OF CONTENTS Specification and part number are subject to change without notice . Multiquip CDM1HHand-Held Core Drill Proposition 65 Warning ............................................. 2Sil...

Page 5 - CDM1H HAND-HELD CORE DRILL — PARTS ORDERING PROCEDURES; Ordering parts has never been easier!; Choose from three easy options:; Order via Internet; Order; Order via Fax

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 5 CDM1H HAND-HELD CORE DRILL — PARTS ORDERING PROCEDURES www .multiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: R Dealer ...

Page 6 - CDM1H HAND-HELD CORE DRILL— SAFETY MESSAGE ALERT SYMBOLS; Model CDM1H

PAGE 6 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) Other important messages are provided throughout thismanual to help prevent damage to your drill, other property,or the surrounding environment. CAUTION - Equipment Damage Hazards ALWAYS wear approved eye and hearing protecti...

Page 7 - CDM1H HAND-HELD CORE DRILL — RULES FOR SAFE OPERATION; MQ Model CDM1H Core Drill.; DANGER

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 7 CDM1H HAND-HELD CORE DRILL — RULES FOR SAFE OPERATION The following safety guidelines should always be used whenoperating the MQ Model CDM1H Core Drill. GENERAL SAFETY ■ D O N OT o p e r a t e o r s e r v i c e t h i s equip...

Page 10 - CDM1H HAND-HELD CORE DRILL — GENERAL INFORMATION; and range in

PAGE 10 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — GENERAL INFORMATION APPLICATION The MQ CDM1H Hand-Held Core Drill is designed to be used for either dry or wet drilling applications involving con-crete type materials. Up to 3-inch (76.2 mm) dia...

Page 11 - Figure 2. CDM1H Core Drill Dimensions; CDM1H HAND-HELD CORE DRILL — SPECIFICATIONS/DIMENSIONS; Bi; ci

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 11 Figure 2. CDM1H Core Drill Dimensions CDM1H HAND-HELD CORE DRILL — SPECIFICATIONS/DIMENSIONS Contact the MQ Sales Department for the coredrill that best fits your application. Table 1 . Thread s /Adapter s and Core Bi t Com...

Page 12 - Figure 3. CDM1H Components; CDM1H HAND-HELD CORE DRILL — COMPONENTS

PAGE 12 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) 1 . Hand-Grip – The CDM1H uses a plastic hand grip to guard against possible electric shock. When drilling,hold this grip firmly. 2 . Reset Button – In the event of an overload press this button. Allow a sufficient amount of...

Page 13 - operate the core drill in a confined; free flow of air; operate the core drill in or around; core bits, water MUST be used to ensure proper cooling.; Figure 5. Drilling with a Standard DRY/WET Core Bit

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 13 CDM1H HAND-HELD CORE DRILL — PRE-SETUP Before Starting: CAUTION - Read Manual Before attempting to operatethis core drill, and to avoidserious injury to personnel,always read and understandoperation manual. Failure toread a...

Page 15 - Applying Power to the Core Drill; Warning - Accidental Starting; Figure 9. Connecting the Power; DANGER - ELECTROCUTION HAZARDS

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 15 Applying Power to the Core Drill 1. This core drill requires 115 VAC, 60 Hz power. Applying power to the drill that is not specified will cause severedamage to the core drill. Always read serial plate tagbefore applying pow...

Page 16 - CDM1H HAND-HELD CORE DRILL — OPERATION; Before Operating; Place the valve on the water source to the; then turn the water valve on the core drill (Figure 8) to the; ON; Warning - Binding of Output Shaft; Figure 11. Wall Drilling Application; NEVER; use the adjustable shoulder stock to; ALWAYS; ALWAYS; drill with uniform pressure and keep; If water is not flowing, check all connections and correct the; DO NOT; overreach. Keep proper footing and

PAGE 16 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — OPERATION Before Operating 1. Place the valve on the water source to the ON position, and then turn the water valve on the core drill (Figure 8) to the ON position (down). Verify that water is fl...

Page 17 - CDM1H HAND-HELD CORE DRILL — SHUTDOWN/MAINTENANCE; Shutdown; Reinstall grease plug and tighten securely.

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 17 CDM1H HAND-HELD CORE DRILL — SHUTDOWN/MAINTENANCE Shutdown 1. Remove the power cord from the wall receptacle or powersource. 2. Allow a sufficient amount of time for the core drill bit to coolbefore attempting to remove it ...

Page 18 - CDM1H HAND-HELD CORE DRILL — TROUBLESHOOTING

PAGE 18 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — TROUBLESHOOTING G N I T O O H S E L B U O R T L L I R D E R O C . 4 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S . k c u t s s i ti B s i . c t e , e n o t s r o r a b l ...

Page 19 - CDM1H HAND-HELD CORE DRILL — WIRING DIAGRAM

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 19 CDM1H HAND-HELD CORE DRILL — WIRING DIAGRAM

Page 20 - CORE DRILL — EXPLANATION OF CODE IN REMARKS COLUMN; SAMPLE PARTS LIST; REMARKS Column

PAGE 20 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) CORE DRILL — EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there...

Page 21 - CDM1H Hand Held Core Drill; CDM1H HAND-HELD CORE DRILL — SUGGESTED SPARE PARTS

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 21 CDM1H Hand Held Core Drill 1 to 5 Units Qty. ..... P/N ......................... Description 2 ......... CD101534 ............... CARBON BRUSH2 ......... CD101560 ............... POWER CORD2 ......... CD101551 ................

Page 22 - CDM1H HAND-HELD CORE DRILL — NAMEPLATE AND DECALS; NAMEPLATE AND DECALS

PAGE 22 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — NAMEPLATE AND DECALS NAMEPLATE AND DECALS

Page 23 - PART NAME; DECAL: MODEL INFORMATION

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 23 CDM1H HAND-HELD CORE DRILL — NAMEPLATE AND DECALS NAMEPLATE AND DECALS NO. PART NO. PART NAME QTY. REMARKS 1 DCL701 DECAL: MODEL INFORMATION 1 2 DCL700 DECAL: CAUTION CLEAN WATER 1

Page 24 - CDM1H HAND-HELD CORE DRILL — CORE DRILL ASSY.

PAGE 24 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — CORE DRILL ASSY. CORE DRILL ASSY. OLD STYLE NEW STYLE 68

Page 28 - CARRYING CASE/TOOLS ADAPTER; TOOL

PAGE 28 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) CDM1H HAND-HELD CORE DRILL —CARRYING CASE /TOOLS/ADAPTER CARRYING CASE/TOOLS ADAPTER 2 6 3 5 4 TOOL KIT 7

Page 29 - ADJUSTABLE WRENCH

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 29 CDM1H HAND-HELD CORE DRILL —CARRYING CASE /TOOLS/ADAPTER CARRYING CASE/TOOLS ADAPTER NO. PART NO. PART NAME QTY. REMARKS 2 * 101566 27 MM WRENCH 1 3 * 101567 ADJUSTABLE WRENCH 1 4 * 101568 5 MM ALLEN WRENCH 1 5 * CD101572 A...

Page 30 - TERMS AND CONDITIONS OF SALE —PARTS

PAGE 30 —CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) TERMS AND CONDITIONS OF SALE —PARTS PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B....

Page 31 - NOTES

CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 31 NOTES

Page 32 - OPERATION AND PARTS MANUAL; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; CANADA

OPERATION AND PARTS MANUAL Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND W HEN CALLING © COPYRIGHT 2010, MULTIQUIP INC. Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written...

Multiquip CDM1H - Manual

Table of Contents:

Summary

Other Multiquip Models