Moen DN7065 - Manual

p

Tool-Fre e Transfe r Be nch

is made of

ABS Plastic , Aluminum, EPDM, and
Stainless .

WARNING

T O PREVENT SERIOUS OR FAT AL INJURY:
Insure product i s assem bl ed, adj usted and used
properl y. FOR USE ONLY BY PERSONS
WEIGHING L ESS T HAN 250 POUNDS. Fai l ure
to fol l ow correct assem bl y and/or adjustm ent
procedures can m ake the seat unstabl e. ALL
FOUR LEGS M UST BE LOCKED IN PLACE AT
T HE SAM E HEIGHT . DO NOT j um p on, stand on
or ti l t. Contact CSI i mm ediately at 1 -800-882 -
0116 i f any co m ponents are m i ssi ng or dam aged.
Do not m odi fy or substi tute any com ponents.
FOR QUEST IONS OR ASSIST ANCE WIT H
ASSEM BLY CONT ACT CSI AT 1 -800-882-0116.
Consul t heal thcare professi onal for advi ce and
i nstructi ons speci fi c to user’s needs before use.



DN7065

– Tool-Fre e Transfe r

Be nch

W hite

1.

Determine orientation of chair relative to w ater supply in order f or transf er bench to
be positioned outside of bathtub.

2.

Locate the tw o under seat support beams: Hold the pieces by the straight end w ith
the curved end aw ay f rom you.

3.

Locate the f lat, indented area of each beam: Place the tw o f lat areas together, so
they are touching, and the tw o beams f orm an "X" shape.

4.

Locate the leg unit w ith top posts that point inw ard: A lign the posts w ith the straight
ends of the crossed support beams on the small end of the "X".

5.

Slide the top posts of the leg unit over the ends of the crossed support beams.

6.

Take the remaining leg unit, w ith the top posts that point straight out, and align it
w ith the curved end of the support beams, at the large side of the " X".

7.

Slide the top posts of the leg unit over the ends of the crossed support beams.

8.

Locate the transf er bench. Place it seat side dow n.

9.

Place the curved ends of the crossed support beams into the grooves on the
underside of the transf er bench, aligning the holes in the support beams w ith the
holes inside the grooves.

10.

Use the assembly knobs to attach the transf er bench to the support beams.
Thread the w ashers onto the bolt, small lock w asher f irst, f ollow ed by the cup
w asher.

11.

Locate the large seat bottom. Place it under the support beams so that the center

12.

of the "X" slides into the center of the "X" shaped grooves on the large seat
bottom.

13.

Use the assembly knobs to attach the large seat bottom to the support beams.

Stock Number:

_________________ TF Transfer Bench

By Creative Specialties

Materials:

Installation Instructions:

Stock Numbers:

Dimensions:

Tool Free Transfer Bench

DN7065

Home Care Technical Specification

2 5 3 0 0 A L M O E N D R I V E



N O R T H O L M S T E D , O H 4 4 0 7 0

C O R P O R A T E H E A D Q U A R T E R S : ( 8 0 0 ) 3 2 1 - 8 8 0 9



F A X: ( 8 0 0 ) 8 4 8 - 6 6 3 6

I N T E R N A T I O N A L : ( 4 4 0 ) 9 6 2 - 2 0 0 0



F A X: ( 4 4 0 ) 9 6 2 - 2 7 2 6

C U S T O M E R S E R V I C E ( U S A ) : 8 0 0 - 8 8 2 - 0 1 1 6



F A X: ( 8 8 8 ) 3 7 9 - 2 7 2 0

W W W . M O E N . C O M



Copyri ght Creati ve Specialties International

Li terature #BA1370