Moen 5401 - Manual

Moen 5401 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

These are shown in the drawings. The depth measurement is critical. Use
the front face of the plaster ground as a reference point for the finished
wall position, including tile (2-1/16" [52mm]). The center line of the supply
and discharge piping should be a maximum of 2-3/16" (56mm) and a minimum
of 1-7/16" (37mm) behind the finished wall surface.

Available with three or four port castings, with and without stops.

Connections are either 1/2 inch I.P.S. pipe or 1/2 inch copper sweat connections.

If the Moen Slip Fit spout is used, a 1/2 inch copper drop and lookout may be used.

CAUTION:

Always turn water off before disassembling the valve. Open valve handle to
alleviate water pressure to insure that complete water shut-off has been
accomplished.

Before turning water on during either rough-in or trim-out, make sure that cartridge retainer clip is in place. The
cartridge and retainer clip were properly installed and tested before leaving the factory. Although it is unlikely, it is
nevertheless possible that through the handling of the valve by any number of persons the retainer clip may not be
properly installed. This should be carefully checked at time of rough-in and trim-out. If the retainer clip is not properly
installed, water pressure could force the cartridge out of the casting. Personal injury or water damage to the
premises could result.

HANDLE

COVER

HANDLE

KNOB

WASHER

HANDLE

SCREW

HANDLE

LEVER

HANDLE ASSEMBLY

ADJUSTABLE

TEMPERATURE

LIMIT STOP

ESCUTCHEON

PLASTER

GROUND

CAUTION

USE 1/2"

IRON PIPE

SIZE

MINIMUM

OR 1/2"

TUBING.

SUPPLY

45"

(1143mm)

48"

(1219mm)

1-1/4"

(32mm)

6' 6"

(1981mm)

32"

(813mm)

FINISHED WALL

LINE

2-1/16"
(52mm)

2-1/16"

(52mm)

TUB FILLER

OR SHOWER

TUB/SHOWER

COMBINATION

FLOOR

15/16"

(24mm)



CLIP

EAR

IMPORTANT: SEE FLUSHING
INSTRUCTIONS PAGE 2

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Stop Operation; MAKE SURE ALL WATER SUPPLIES ARE OFF.; CAUTION; Flushing

Stop Operation CC - This type is integral with casting, actuated by screwdriver, and require a 90 ° turn to open or close. When the screwdriver slot is vertical, the rubber stop is closed, and when the slot is horizontal, the rubber stop is open. IPS - This type has been added to the basic shower ca...

Page 3 - TO REMOVE STOP VALVE; Not for use with Moentrol valves.

Disassembly Turn "OFF" both hot and cold water supplies, then open faucet to relieve pressure. Remove handle cover from handle knob. Take out handle screw andremove handle knob, washer, and stop tube. Lift out retainer clip. Rotate cartridge shell back and forth with Moen cartridge twist wre...

Page 4 - Reversed Rough-In Where Hot and Cold Positions Are Reversed:; Cleaning & Care Instructions

25300 Al Moen Dr., North Olmsted, OH 44070-8022 U..S.A. HELPLINE: Call our toll free Helpline number, for answers to any product, installation, replacementparts, or warranty questions. MT620J AUG '96 To Eliminate Cross-Piping On Back-To-Back Installations or To Correct Reversed Rough-In Where Hot an...