Moen 4643 - Manual
Moen 4643 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Lift Rod & Waste Assembly; Installation
- Page 3 – Disassembly; Reassembly; Cleaning & Care Instructions for
- Page 4 – Consumer Information
LAVATORY FAUCETS
Four-Inch Centerset
4200, 4220, 4330, 4340, 4350,
4400, 4641, 4643 SERIES
INSTALLATION INSTRUCTIONS
THESE INSTRUCTIONS MUST BE
LEFT WITH HOMEOWNER
MT123A
®
CAUTION:
Always turn water off before disassembling the valve. Open valve handle to alleviate water
pressure to insure that complete water shut-off has been accomplished.
Before turning water on during either rough-in or trim-out, make sure that the cartridge retainer clip is in place. The cartridge and
retainer clip were properly installed and tested before leaving the factory. Although it is unlikely, it is nevertheless possible that
through the handling of the valve by any number of persons the retainer clip may not be properly installed. This should be carefully
checked at time of rough-in and trim-out. If the retainer clip is not properly installed, water pressure could force the cartridge out
of the casting. Personal injury or water damage to the premises could result.
Clip
Ear
6" X 2" WIDE
1/2" IPS
THREADED
CONNECTIONS
LIFT ROD
POSITION
USE SPACER TO INSTALL
ON THINNER LAVATORY
BOWLS OR COUNTERS
DISCARD SPACER WHEN
INSTALLING ON THICKER
LAVATORY BOWLS OR COUNTERS
1-3/4"
MAX.
4-3/4"
3-5/8" C.C.
1-3/4"
5" NOMINAL
OPEN
POSITION
5" NOMINAL
OPEN
POSITION
CONCENTRIX HANDLE
HANDLE INSERT
(NOT
INCLUDED)
3-5/8" C.C.
1-3/4"
3-5/8" C.C.
1-3/4"
5" NOMINAL
OPEN
POSITION
LEVER HANDLE
KNOB HANDLE
TILT BACK
CLAMP BAR
With clamp bar, spacer and
mounting nut installed, tilt
clamp bar back as shown,
then drop faucet supplies
down through deck holes and
tighten from below. On decks
thicker than 3/4" you may
have to remove spacer.
Fits 4" centers and through a 1" minimum diameter hole.
All models equipped with a Moen Flow-Rator™.
Complies with ASME A112.18.1M and CSA B125
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Lift Rod & Waste Assembly (For model with grid strainer assembly follow steps 1-3 only) 1. Thoroughly clean around drain opening in lavatory basin. Apply 1/4 inch bead of plumber's putty (not furnished) around theunderside of seat (as shown). 2. Apply pipe joint compound or Teflon tape (not furn...
Disassembly CAUTION: Turn OFF both hot and cold water supplies. Open handle to alleviate water pressure to insure thatcomplete water shut-off has been accomplished. For Knob Models:1. Remove handle cover, handle screw, knob, stop tube, washer, and retainer clip. For Concentrix Handle Models:1. Remov...
Moen Incorporated 25300 Al Moen Drive, North Olmsted, OH 44070-8022, U.S.A. In Canada: Moen Inc. 2816 Bristol Circle, Oakville, Ontario L6H5S7 MT123A SEP 95 © Copyright 1995 Moen Incorporated Printed in U.S.A. Consumer Information Faucets made of leaded brass alloys may contribute small amounts of l...
