Moen 2400 Series - Manual
Moen 2400 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CAUTION; Flushing
- Page 3 – Reassembly; TO REMOVE STOP VALVE; Not for use with Moentrol valves.
- Page 4 – Reversed Rough-In Where Hot and Cold Positions Are Reversed:; Cleaning & Care Instructions
MT659C
MODELS 2200, 2400 & 72200 SERIES
INSTALLATION INSTRUCTIONS
THESE INSTRUCTIONS MUST BE
LEFT WITH HOMEOWNER
TUB AND SHOWER VALVES
All models have 4 port castings. Stops are optional on all models. All models are also available for 1/2 inch I.P.S. pipes
or 1/2 inch copper sweat connections to copper water tubing. The 2400 series include built in pushbutton diverter.
Measurements
CAUTION:
Always turn water off before disassembling the valve. Open valve handle to
alleviate water pressure to insure that complete water shut-off has been
accomplished.
Before turning water on during either rough-in or trim-out, make sure that cartridge retainer clip is in place. The
cartridge and retainer clip were properly installed and tested before leaving the factory. Although it is unlikely, it is
nevertheless possible that through the handling of the valve by any number of persons the retainer clip may not be
properly installed. This should be carefully checked at time of rough-in and trim-out. If the retainer clip is not properly
installed, water pressure could force the cartridge out of the casting. Personal injury or water damage to the
premises could result.
UP
These are shown in the drawings. The depth
measurement is critical. Use the front face of
the plaster ground as a reference point for the
finished wall position, including tile (2-1/16"
[51mm]). The center line of the supply and
discharge piping should be a maximum of 2-3/16"
(56mm) and a minimum of 1-7/16" (37mm) behind
the finished wall surface.
UP
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
HANDLE
COVER
O-RING
HANDLE
SCREW
HANDLE
KNOB
ESCUTCHEON
WASHER
PLASTER
GROUND
1-1/4"
(32mm)
2-1/16"
(52mm)
CAUTION:
USE 1/2" IRON
PIPE SIZE
MINIMUM. DO
NOT USE 1/2"
TUBING, EXCEPT
WHEN SLIP FIT
SPOUT IS USED.
COMBINATION
MODELS 32"
(813mm)
SHOWER
45"
(1143mm)
48"
(1219mm)
6'6"
(1981mm)
SUPPLY 1/2" I.P.S. OR
COPPER SWEAT
2400 MODEL SERIES
PUSH BUTTON DIVERTER
MODEL ILLUSTRATED
ALL DIMENSIONS NOMINAL
➤
WALL LINE
FLOOR
UP
®
CLIP
EAR
IMPORTANT: SEE FLUSHING
INSTRUCTIONS PAGE 2
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
MT659C Stop Operation CC - This type is integral with casting, actuated by screwdriver, and require a 90 ° turn to open or close. When the screwdriver slot is vertical, the rubber stop is closed, and when the slot is horizontal, the rubber stop is open. IPS - This type has been added to the basic sh...
Disassembly Turn OFF both hot and cold water supplies, then open faucet to relieve pressure. Remove handle cover from handle knob. Take out handle screw and removehandle knob, washer, and stop tube. Lift out retainer clip. Rotate cartridge shell back and forth with Moen cartridge twist wrench, grasp...
HELPLINE: Call our toll free Helpline number, for answers to any product, installation, replacementparts, or warranty questions. 25300 Al Moen Dr., North Olmsted, OH 44070-8022 U.S.A. To Eliminate Cross-Piping On Back-To-Back Installations or To Correct Reversed Rough-In Where Hot and Cold Positions...
