Mitsubishi MZ360360EX- User Manual

Mitsubishi MZ360360EX

Mitsubishi MZ360360EX– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
Page: / 51

Table of Contents:

  • Page 2 – TOOLS; COMPONENTS; PRECAUTIONS; the radio presets after the installation is completed.; Note
  • Page 4 – QUICK SPLICE CONNECTOR; Precautions for installing quick splice connector
  • Page 5 – Check; Caution
  • Page 8 – C. INSTALLING THE ANTENNA UNIT
  • Page 11 – G. ROUTING THE HARNESS AROUND; to the 1-pin connector of the front harness taped
  • Page 14 – J. REGISTRATION AND OPERATION CHECK; Be careful not to pinch the harnesses or damage the parts.
  • Page 21 – G. ROUTING THE HARNESS AROUND THE ETACS-ECU; along the front harness and connect it to the 1-pin; The connector drawings show the positions of the
  • Page 22 – Never separate the 38-pin connector halves.
  • Page 24 – H. INSTALLING THE HOOD SWITCH (vehicles without theft alarm system); must be installed.
  • Page 26 – K. REGISTRATION AND OPERATION CHECK
  • Page 37 – REGISTRATION AND OPERATION CHECK PROCEDURES
  • Page 39 – Registration is completed
  • Page 42 – Circuit Diagram
  • Page 44 – Troubleshooting
  • Page 51 – Checking Harnesses
Loading the manual

 

REMOTE ENGINE STARTER

MZ360360EX

INSTALLATION INSTRUCTIONS

 

Applicable Models

GALANT(09.5MY-)

，

ECLIPSE/SPYDER(10MY-)

，

ENDEAVOR(09MY-)

 
 
 

 

Thank you for purchasing the Mitsubishi Genuine Accessory.

To install and use the product correctly with proper knowledge of it, read this publication carefully.

Keep this publication for reference when maintenance is required.

-

 

This publication gives precautionary instructions in the boxes titled as follows.

Read through these instructions thoroughly.

 

 

 

 

 

 

- Failure to follow these instructions not only prevents the product from working properly but may lead to trouble

with the vehicle. Be sure to follow all instructions carefully.

- If there is anything unclear about the installation, handling and/or usage of the product, contact your Mitsubishi

Motors dealer for clarification.

- Mitsubishi Motors Corporation is not responsible for any defects or difficulties caused by or resulting from the

failure to follow given instructions.

- We recommend you to have the installation performed at an authorized Mitsubishi Motors dealer.

 
 
 
 
 
 
 
 

 

 

 

Caution

!


This system is exclusively for automatic transmission vehicles. Never install this system on manual
transmission vehicles.

Warning

!

Describes precautions that should be observed in order to prevent serious injury or

death to the user.

Describes precautions that should be observed in order to prevent injury or damage

to the vehicle or its components, which may occur if sufficient care is not taken.

Provides additional information that facilitates installation work.

Note

ZZ100-00420-0

10, 8

To the dealer:
Be sure that the customer receives this publication

.

Attention

Warning

!

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - TOOLS; COMPONENTS; PRECAUTIONS; the radio presets after the installation is completed.; Note

- 2 - ■ TOOLS (Make the following tools ready for use.) Socket wrench (10mm)       Extension bar       Phillips screwdriver (medium)       Scissors             Cutting pliers       Trim remover             Scale               Vinyl tape                 Multimeter Pliers    Isopropyl alcohol or degre...

Page 4 - QUICK SPLICE CONNECTOR; Precautions for installing quick splice connector

- 4 -   ■ QUICK SPLICE CONNECTOR Precautions for installing quick splice connector - Be careful not to damage the vehicle harness when cutting the vinyl tape wound around the harness to expose the wire to which the quick splice connector is to be installed. - When connecting a quick splice connector...

Page 5 - Check; Caution

- 5 - INSTALLATION PROCEDURES FOR ECLIPSE/SPYDER A. PREPARATORY WORK    1) Confirm that the ignition key is removed and all the electrical switches are off. Then disconnect the battery (–) cable from the battery. 2) Remove the following parts in accordance with the workshop manual. 1. Instrument pan...

Other Mitsubishi Models