Mitsubishi Electric XD8100U - Manual
Mitsubishi Electric XD8100U – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – You can assign the ID code to the control command.; RXD; Communications format
- Page 3 – Control command configuration; of the command varies among the functions.; the receiving order; • NAK return
- Page 4 – (The statuses are echoed back as; • When ID is not specified:; with the ID of “01” or “ALL.”
- Page 6 – Reading command diagram
- Page 8 – Remote commands
- Page 9 – Direct commands; command with the current setting value added as a data code.; How to set the value; Use the character or ASCII code as shown below to set the value.; Function commands; screen is being displayed, the splash screen is only canceled.)
- Page 10 – Menu setting commands; value as the data code and send it back to the PC.
- Page 14 – Use the character
- Page 15 – picture control (ID command is
- Page 16 – Password lock commands
- Page 17 – Execution procedure of RS-232C commands via LAN; ter string for creating the certification data); The default password is “admin.”
1
DLP™ Projector
XD8100U
Controlling the projector using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
In addition, by connecting multiple projectors to each other in a daisy chain configuration, you can control each
projector from one personal computer.
PC-controllable functions:
• Turning the power ON or OFF
• Changing input signals
• Inputting commands by pressing the buttons on the control panel and remote control
• Menu setting
[Compatibility with the former models]
To u s e t h e R S - 2 3 2 C c o m m a n d s d e s i g n e d f o r t h e f o r m e r m o d e l s o f M i t s u b i s h i p ro j e c t o r, b y i n p u t t i n g
“00COMMAND0”, the projector responds in the same way as the former models. (No NAK is returned. ID code
cannot be designated at command sending.)
(For the recommended procedure to use the former command systems, see “Controlling the projector using a
personal computer” for FL7000U.)
ITEM
Function
Data
Character
ASCII code
Changing the RS-232C
command system
COMMAND
43h 4Fh 4Dh 4Dh 41h 4Eh 44h
0 (Former command system), 1 (New
command system)
Connection
Important:
• Make sure that your computer and projector are turned off before connection.
• Boot up the computer first, and then plug the power cord of the projector.
(If you do not follow this instruction, the Com port may not function.)
• To use a daisy chain configuration, make sure to use Mitsubishi projectors supporting RS-232C communication. If
the projectors or other devices made by other manufacturers are connected, operation is not guaranteed.
To connect with one projector:
RS-232C cable
D-SUB 9-pin
To SERIAL IN
terminal
To RS-232C terminal
D-SUB 9-pin
To connect with multiple projectors (in a daisy chain configuration):
RS-232C cable
D-SUB 9-pin
To SERIAL IN
terminal
To RS-232C terminal
To SERIAL IN
terminal
To SERIAL OUT
terminal
To SERIAL OUT
terminal
D-SUB 9-pin
RS-232C cable
D-SUB 9-pin
D-SUB 9-pin
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 • Example of ID setting (When Group A, which performs multi-projection with two projectors, and Group B, which performs multi-projection with three projectors, are connected.) Projector 1 PROJECTOR ID : 01 GROUP ID : A Multi-projection Group A Projector 2 PROJECTOR ID : 02 GROUP ID : A Projector 3...
3 2. Control command configuration The command consists of the address code, ID code, function code, data code, ACK/NAK, and end code. The length of the command varies among the functions. Address code ID code Function code Data code ACK/NAK End code ASCII code ‘30h’ ‘30h’ ‘30Bh’ ID ‘30Bh’ Function ...
4 • The projector may not receive a command when the splash screen is being displayed immediately after turning on the power. Use command “00r10” to cancel the splash screen. • While using the LAN terminals, the LAN functions take precedence. • For the LAN terminals, the same commands as those for c...
