Page 3 - DIAMOND SHIELD; CONTENTS
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 3 INTRODUCTION ................................................................................................................................ 5 Model Dimensions and Weight Specifiations .............................
Page 5 - PRODUCT SAFETY NOTICE; When
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 5 This service manual includes: 1. Assembly and disassembly instructions for the front and rear cabinet components.2. Servicing of the Lenticular Screen and Fresnel Lens.3. Servicing down to major components, chass...
Page 6 - SAFETY PRECAUTIONS; Leakage current check:
Page 6 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 SAFETY PRECAUTIONS NOTICE: Observe all cautions and safety related notes located inside the receiver cabinet and on thereceiver chassis. WARNING: 1. Operation of this receiver outside the cabinet or with the cove...
Page 7 - SPEAKER GRILLE & BEZEL Removal; CABINET FRONT DISASSEMBLY
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 7 SPEAKER GRILLE & BEZEL Removal 1) Pull the SPEAKER-GRILLE away from the cabinet to remove. 2) Pull the BEZEL from the cabinet. SCREEN-ASSY Removal 1) Remove 10 screws (a) from the upper cabinet rear cover (3 ...
Page 9 - BEZEL Removal
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 9 SIDE-TRIM Removal 1) Remove screws (a) and (b) on eachside of the unit. 2) Pull off the SIDE-TRIM on each side. BEZEL Removal 1) Remove screws (c) to remove the BEZEL. WD-62827 Front Disassembly (continued)
Page 10 - SCREEN ASSY Removal
Page 10 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 SCREEN ASSY Removal 1) Remove screws (e) from the top and sides of the upper rear cover. 2) Remove screws (d) from the bottom of the SCREEN ASSY. 3) Lift the SCREEN ASSY up slightly and pull away from the cabine...
Page 11 - outer
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 11 FRONT ESCUTCHEONS, CARD READER/CONTROL Assy and PEDESTAL COVER Removal 1) Remove 6 outer screws “A” at the rear sides of the cabinet. (Do not remove inner screws). 2) Pull the Right and Left Front Escutcheons fr...
Page 12 - TOP, BOTTOM and SIDES TRIM Removal
Page 12 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 TOP, BOTTOM and SIDES TRIM Removal 1) Remove screws (b) to remove the Top Trim. 2) Remove screws (c) to remove the Bottom Trim. 3) Remove screws (d) on both sides to remove the Side Trim WD-62927 Front Disassemb...
Page 13 - FRONT BEZEL Removal
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 13 FRONT BEZEL Removal 1) Remove screws (e) from the FRONT-BEZEL. 2) Pull the FRONT-BEZEL from the cabinet. WD-62927 Front Disassembly (continued)
Page 14 - SCREEN ASSEMBLY Removal
Page 14 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 WD-62927 Front Disassembly (continued) SCREEN ASSEMBLY Removal 1) Remove screws (f) from the upper rear cover (3 at each side and 4 acrross the ). 2) Remove screws (g) at the bottom of the screen. 3) Lift the Sc...
Page 15 - CARD READER REMOVAL
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 15 WD-73727 / WD-73827 Front Disassembly CARD READER REMOVAL 1) Pull the two PANEL-FRONTs from the cabinet. 2) Remove screws ((a) from the Card Reader. 3) Slide the Card Reader and Control Assembly out the front of...
Page 19 - Cabinet Rear Disassembly; Accessing the MIRROR from the rear (52 and 62 inch models ONLY)
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 19 Cabinet Rear Disassembly BACK-COVER Removal 1) Remove screws (a) and (b) from the the BACK-COVER. 2) Pull the BACK-COVER from the set. Accessing the MIRROR from the rear (52 and 62 inch models ONLY) 1) Remove sc...
Page 20 - Chassis Disassembly / Accessing PWBs; disassembly step; Chassis Sequence of Disassembly
Page 20 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Chassis Disassembly / Accessing PWBs Note: Although not individually indicated, unplug the required connectors in each disassembly step . REMOVE Chassis Top Cover (Fig. 1) REMOVE PWB-POWER (Fig. 3) REMOVE Assy P...
Page 21 - Chassis Removal from the cabinet
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 21 Chassis Removal from the cabinet After removing the Rear Cover: 1) Remove screw (a), (b) and (c) to remove theback terminal board cover. (Figure A) 2) Remove screw (d) to remove the support bracketon each side o...
Page 26 - OPERATING CHASSIS OUTSIDE OF CABINET; PS
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 26 OPERATING CHASSIS OUTSIDE OF CABINET 1) Remove screws from back terminal board.Screws A = (7) , B = (2) , C = (2) 2) Remove support bracket screws D = (4) , and mounting screw E = (1) 4) Remove mounting screw F ...
Page 27 - DVI cable; Front
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 27 7) Pictured below is proper wire routing, pleaseverify during re-assembly 8) Disconnect connector PL and remove screw H = (1) PL 9) Remove connectors PC, PA1, PB, PD and DVI cable 10) Remove cover shield for Pow...
Page 28 - from Micro PWB; AC Cord; JD
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 28 13) Pull Terminal PWB from chassis assemblyand remove fan connector JD from Micro PWB 14) Setup power section next to remainingchassis section as pictured below. NOTE: Unit can be operated without Terminal PWB o...
Page 29 - OPTICAL ENGINE REPLACEMENT; GROUND STRAPS
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 29 52” & 62” Models OPTICAL ENGINE REPLACEMENT (View from back) Ballast Fan Ballast Cover Lamp Cartridge Interface PWB Engine PWR PWB Ballast Plate Lamp Duct Lens Cushion (View from front) Engine Plate Bottom P...
Page 30 - JF
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 30 52” & 62” Models OPTICAL ENGINE REPLACEMENT (Details) 1) Remove screws (3) 2) Remove mounting screw 3) Disconnect JA, JF, LT connectors 4) Disconnect JC and CD connectors 5) Remove DVI cable and disconnect J...
Page 33 - Mechanical Alignment:; Lens Cushion Base; Spring
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 33 52” & 62” Models OPTICAL ENGINE REPLACEMENT (Details) Reassembly: 1) Attach LENS CUSHION BASE to Engine Follow above steps in reverse order Mechanical Alignment: Adjustment is required after engine has been ...
Page 34 - 3 “ Model’s OPTICAL ENGINE REPLACEMENT; GROUND
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 34 73 “ Model’s OPTICAL ENGINE REPLACEMENT Pull engine assembly from the cabinet, and remove the Optical Engine from the base.Remove all the listed parts on this page and transfer them to new engine. Then transferE...
Page 35 - 3” Models OPTICAL ENGINE REPLACEMENT (Details); Engine Assembly removal from the cabinet
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 35 73” Models OPTICAL ENGINE REPLACEMENT (Details) Engine Assembly removal from the cabinet . After removing the Back Cover:1) Remove 4 screws (a) to remove the Vertical Support and DM Fan Cover.2) Remove screw (b)...
Page 37 - ) Carefully lift the Engine from the Base Plate.
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 37 73” Models OPTICAL ENGINE REPLACEMENT (Details) 4) Carefully lift the Engine from the Base Plate. CAUTION: Do Not lose the spring sitting in the Base Plate Assembly. Engine removal from the Base Plate Assembly (...
Page 38 - DIAMOND SHIELD REPLACEMENT; To Remove the Diamond Shield:; WARNING
Page 38 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 DIAMOND SHIELD REPLACEMENT (WD-62927 / WD-73927 Only) To Remove the Diamond Shield: 1) While wearing soft cotton gloves,loosen the sides of the Diamond Shieldby pressing a small plastic card (thesize of a standa...
Page 39 - SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS; Wear gloves; Do not place Fresnel Lens in the sun; Lenticular Screen and Fresnel Lens Removal
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 39 SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS CAUTION: Wear gloves when handling the Lenticular Screen and Fresnel Lens. This prevents cuts and finger prints. Do not place Fresnel Lens in the sun . This may c...
Page 40 - Lenticular Screen and Fresnel Lens Installation
Page 40 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS Lenticular Screen and Fresnel Lens Installation Note: Store the Lenticular Screen and Fresnel Lens in a cool dry place. High humidity may deform the Lenticular Sc...
Page 41 - OPTION MENU
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 41 OPTION MENU 1. Press the “MENU” button on the remote hand unit.2. Press the buttons “2”, “4”, “7” and “0” in order. (The screen will change to the option menu.) Setup Menu L-Adult Language Enable Language Englis...
Page 42 - LED Indicator Diagnostics; Normal LED Indications
Page 42 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 A. A/V Memory Each of the external inputs has its’ own Audio/Video Memory. A change in an A/V setting at a specific input is stored in memory for that specific input. B. A/V Reset 1. On the front panel , pressin...
Page 43 - Error Code Operational Check; Abnormal LED Indications
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 43 3. Error Code Operational Check Note: The TV must be in “Shut Down” and not have been switched Off, to perform the Error Code Opera- tional Check. When the TV is switched Off, the code automatically resets to “1...
Page 44 - SERVICE MANUAL SUPPLEMENT; COPYRIGHT © 2007 MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.; AIR FILTER CLEANING; If the TV shuts off after displaying the message “; Lamp Cartridge. Use the following steps for filter cleaning.; Lamp Cartridge - Air Filter; MODELS
SERVICE MANUAL SUPPLEMENT COPYRIGHT © 2007 MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. ALL RIGHTS RESERVED AIR FILTER CLEANING If the TV shuts off after displaying the message “ TV will shut down in a few seconds. Please check if the air flow is blocked.” and/or the Status LED is yellow, the Air Fi...
Page 45 - SERVICE ADJUSTMENTS; Measuring equipment and Jigs; Circuit Adjustment Mode
Page 44 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 SERVICE ADJUSTMENTS There are only 5 Service Adjustments required in these models: Two Electrical Adjustments • Horizontal Centering• Vertical Centering Three Mechanical Adjustment • Picture Rotation• Horizontal...
Page 46 - Adjustment Selection; Terminating the circuit adjustment mode; Resetting Data to Factory Values; Data Transfer; Display
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 45 3. Adjustment Selection Use the “VIDEO” button to select a specific electrical ajustment, “1 HPOS” or “2 VPOS”. 4. Adjusting Data After selecting an adjustment item, use the “UP” and “DN” buttons to change adjus...
Page 47 - Prelminary; Optical Engine Adjustments; Test Signal Activation
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 42 Prelminary Mechanical Optical Engine Adjustments are made using the UNIT-ADJUSTER shown in Figure 1. The UNIT-ADJUSTER is mounted under the Light Engine on the Engine Plate. It is accessed from the front of the ...
Page 48 - ACCESSING MECHANICAL ADJUSTMENTS; Speaker Grille
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 47 WD-52627 / 62627 / 52628 / 62628 1) Pull Speaker Grille out.2) Remove (2) screws (A) and pull Card Reader to access adjustment. ACCESSING MECHANICAL ADJUSTMENTS A Speaker Grille WD-62827 1) Remove (6) screws (A)...
Page 50 - Remove only the outside screws; . Do not remove inside; Locking Screws and Wedge Removal
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 49 WD-73927 1) Remove (16) screws (A). 8 on each side. ( Remove only the outside screws . Do not remove inside screws, they are for the Screen Frame) 2) Pull Front Panel Escushions from unit. 3) Remove (8) screws (...
Page 51 - ADJUSTMENT PROCEDURES; Adjustment Locations; WEDGE
Page 50 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 ADJUSTMENT PROCEDURES Adjustment Locations The Mechanical Adjustements are accessedthough the opening for the Card Reader.Locations of the Adjustmentts are shownbelow. CAUTION: Do Not force an adjust- ment past ...
Page 52 - ment; Electrical Adjustments; RUBBER; Figure 6: Wedge Insertion
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 51 Rotation Adjustment Adjust [A-2] to remove any picture rotation Horizontal Keystone Adjustment Adjust [A-3] to remove horizontal keystone distortion. NOTE: Vertical Positioning may shift Vertical Keystone Adjust...
Page 53 - Using Lead Free Solder; Pb Solder; Only Lead; Displays used to indicate Pb-free; LFS
PAGE 52 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Using Lead Free Solder Pb Solder The above symbol indicates Lead (Pb) Free solder wasused during the construction of PWBs. Only Lead Free solder should be used when servicing these PWBs. Solder must be compatibl...
Page 54 - CHIP PARTS REPLACEMENT; Replacement
PAGE 53 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 CHIP PARTS REPLACEMENT Some resistors, shorting jumpers (0 Ohm resistors),ceramic capacitors, transistors and diodes are chip parts.The following precautions should be taken when replacingthese parts. Cautions: ...
Page 55 - REPLACEMENT PARTS
PAGE 54 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Parts Ordering To expedite delivery of replacement parts orders, specify the following: 1. Model Number/Serial Number 2. Part Number and description 3. Quantity Note: Unless complete information is supplied, del...
Page 56 - QUICK REFERENCE FOR COMMON PARTS; OPTICAL COMPONENTS; MIRROR & SCREEN PARTS; MISCELLANEOUS PARTS; MAJOR PWB ASSEMBLIES
PAGE 55 MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 QUICK REFERENCE FOR COMMON PARTS Component Part No. Models LIGHT ENGINE 938P017010 WD-52627 / 52628 938P017020 WD-62627 / 62628 938P019020 WD-62827 / 62927 938P019010 WD-73727 / 73827 / 73927 PWB-BALLAST 938P118...
Page 57 - INTEGRATED CIRCUITS
Ref # Part # Part Name & Description [#] PAGE 56 Ref # Part # Part Name & Description [#] MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 [#] Model Legend: (a) WD-52627, (b) WD-52628, (c) WD-62627, (d) WD-62628, (e) WD-62827, (f) WD-62927, (g) WD-73727, (h) W...
Page 58 - TRANSISTORS; DIODES
PAGE 57 Ref # Part # Part Name & Description [#] MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 [#] Model Legend: (a) WD-52627, (b) WD-52628, (c) WD-62627, (d) WD-62628, (e) WD-62827, (f) WD-62927, (g) WD-73727, (h) WD-73827, (i) WD-73927 Ref # Part # Part Name ...
Page 59 - COILS
Ref # Part # Part Name & Description [#] PAGE 58 Ref # Part # Part Name & Description [#] MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 [#] Model Legend: (a) WD-52627, (b) WD-52628, (c) WD-62627, (d) WD-62628, (e) WD-62827, (f) WD-62927, (g) WD-73727, (h) W...
Page 65 - SWITCHES
Ref # Part # Part Name & Description [#] PAGE 64 Ref # Part # Part Name & Description [#] MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 [#] Model Legend: (a) WD-52627, (b) WD-52628, (c) WD-62627, (d) WD-62628, (e) WD-62827, (f) WD-62927, (g) WD-73727, (h) W...
Page 67 - PRINTED CIRCUIT BOARDS
Ref # Part # Part Name & Description [#] PAGE 66 Ref # Part # Part Name & Description [#] MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 [#] Model Legend: (a) WD-52627, (b) WD-52628, (c) WD-62627, (d) WD-62628, (e) WD-62827, (f) WD-62927, (g) WD-73727, (h) W...
Page 68 - SCREEN ASSEMBLY PARTS
PAGE 67 Ref # Part # Part Name & Description [#] Ref # Part # Part Name & Description [#] MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 [#] Model Legend: (a) WD-52627, (b) WD-52628, (c) WD-62627, (d) WD-62628, (e) WD-62827, (f) WD-62927, (g) WD-73727, (h) W...
Page 69 - Not Shown
PAGE 68 Ref # Part # Part Name & Description [#] Ref # Part # Part Name & Description [#] MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 [#] Model Legend: (a) WD-52627, (b) WD-52628, (c) WD-62627, (d) WD-62628, (e) WD-62827, (f) WD-62927, (g) WD-73727, (h) W...
Page 70 - Figure 3
PAGE 69 Ref # Part # Part Name & Description [#] Ref # Part # Part Name & Description [#] MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 [#] Model Legend: (a) WD-52627, (b) WD-52628, (c) WD-62627, (d) WD-62628, (e) WD-62827, (f) WD-62927, (g) WD-73727, (h) W...
Page 72 - Main Power Supply
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 71 Main Power Supply
Page 75 - Analog Video Signal Path
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 74 Analog Video Signal Path
Page 77 - HDD Record Signal Path
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 76 HDD Record Signal Path (V30+ and V31 Only)
Page 78 - Sound Signal Path
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 77 Sound Signal Path
Page 80 - Lamp Control Circuitry
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 79 Lamp Control Circuitry
Page 81 - TV Guide On® Screen Block Diagram
MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927 Page 80 Lamp, Engine & Fan Protect Circuitry TV Guide On® Screen Block Diagram
Page 83 - COLD
3 9 2 5 6 8 10 1 7 4 3 9 14 20 2 16 5 11 6 13 8 18 10 19 15 1 17 7 4 12 21 22 23 24 11 10 12 3 9 2 5 6 8 1 7 4 A-GND 18VS 5VS 5VS LAMP-RELAY ENG-PWR-ON 5VSL A-GND -15VS +15VS A-GND +15VS 5VSL STBY STBY-SHORT A-GND -15VS 12VS A-GND AC-OFF PON-SHORT 18VS 18VS 5VSL MAIN-RELAY MAIN-RELAY 5VR PWR-ON STBY...
Page 84 - TO POWER
3 9 14 20 2 16 5 11 6 13 8 18 10 19 15 1 17 7 4 12 21 22 23 24 3 9 14 2 5 11 6 13 8 10 1 7 4 12 BOSS 3 9 14 2 16 5 11 6 13 8 10 15 1 7 4 12 3 9 14 20 2 16 5 11 6 13 8 18 10 19 15 1 17 7 4 12 L9J04 68MH 9X9.5 L9J05 68MH 9X9.5 L9J06 68MH 9X9.5 2K1/16W R9J03 1K1/16W R9J04 2K1/16W R9J20 2K1/16W R9J21 2K...
Page 85 - CE
58K 58K BIAS 58K 58K BIAS GND GND TS T 1 B S T S T1 B S R2J22 75 1/16W R2J16 75 1/16W R2J2375 1/16W R2J21 75 1/16W R2J1875 1/16W R2J17 75 1/16W 75 R2J34 75 R2J39 75 R2J40 120K1/16W R2J37 120K1/16W R2J42 75 1/16W R2J41 751/16W R2J36 120K1/16W R2J38 120K1/16W R2J43 75 R2J35 10K 1/16W R2L27 10U C2L14 2...
Page 86 - TO DM PWB
BOSS BOSS BOSS BOSS 11 10 12 3 9 14 2 5 11 6 13 8 10 1 7 4 12 1/16W R7L27 F-2.2K 50V C7K28 10U Z-0.1 C80E2 25V/16V 1/16W R7L32F-56K Z-.1 C80E3 25V/16V GND 12K1/16W R7K25 16V C7K01 47U 1/16W R7K32 4.7K GND GND Z-.1 C80E1 25V/16V 2.7K1/16W R7K34 GND 1/16W R7L28 F-3.3K 3.3K 1/16W R7K02 K-0.1 C7K25 16V ...
