Mitsubishi Electric P91DW - Manual

5 UNPACKING 3 1 1 1 1 1 Open the top of the box. 2 2 2 2 2 Remove the cushion above the unit. • Make sure to keep the unithorizontal. 3 3 3 3 3 Take the unit out of the box carefully. Take the unit out of the box by the following procedures. Make sure to check thecontents. 4 4 4 4 4 Unwrap the unit....

6 FEATURES AND FUNCTIONS 4 Front Panel Turns on/off the power. Power switch 1 Function mode changes whenever FUNCis pressed. FUNC button 2 Press to change the value in functionmode. 3 DOWN button UP button Press to change the value in functionmode. 4 Press to set each function value and γ - curve. S...

7 Rear Panel Select special functions. Mode switches C PARALLEL data terminal Function Name Reference page 10 10 Connects to the device equipped withparallel data interface such as personalcomputer. D E 20 - 22 F - - Power terminal (AC LINE) Connect the power cord to this terminal. Potential equaliz...

8 4 4 4 4 4 Close the door. INSTALLATION OF PAPER 5 Moisture, fingerprints or dust on thepaper surface may cause a noise atprinting or deterioration in printquality. Set the paper in the followingprocedure to prevent adhesion offingerprint or dust on the papersurface. 1 1 1 1 1 Open the door. • Swit...

9 When setting the paper, observe the followingprecautions to prevent paper jam. Do not use the bent or wrinkledpaper. Do not use defective paper. Do not slack the roll paper. Set the paper tightly to remove anyslack. If the side of the print paper is uneven or the core is sticking out, the amount o...

10 EXAMPLE OF CONNECTION 6 Connecting to various equipment with parallel data interfacesuch as medical equipment and personal computer. Connection 1 Turn off the power switches of the digital monochrome printerand the equipment to be connected. 2 Connect the digital monochrome printer with PC or med...

11 PRINTING 7 Printing procedure 2 You can set the number of copies bypressing the COPY button on the frontpanel. You can copy the same picture asmany times as you desire until a newimage data is printed. 2 When the COPY button is pressed duringcopy printing, the current image will becompleted and t...

12 2 By pressing the "FEED" button on thefront panel, you can feed the paper. Paper feeding 2 If printing is continued with a very black picture, the printer will become overheated andprinting will not be available. " " is indicated, and the button functions become invalid. In this c...

13 8 ADJUSTMENT OF PRINT PICTURE Selection of Gamma ( γ ) Curve γ− curve set mode You can select γ -curve by pressing the gamma button " ". Each time the button is pressed, the indicator and γ -curve number is switched. After a γ -curve number has been selected, press the "SET" butto...

14 9 SETTING OF FUNCTION MODE 1 Select a function mode by pressing the FUNC button. Paper type selection mode Paper saving mode Set condition printing mode Buzzer set mode Standby • Each time the FUNC button is pressed, the mode is switched as shown below. FUNC DOWN SET UP GAMMA FEED

16 10 When an error in operation occurs, an audible alarm and avisible error is displayed in the LED indicator. Cause/Error display Cause/Error display Cause/Error display 1 1 1 1 1 No paper 2 2 2 2 2 Overheat ERROR DISPLAY [Symptom]• When the paper runs out or the paper is not installed, printing b...

17 Cause/Error display Cause/Error display [Symptom]• When the door opens, an alarm tone is given. Symptom/Remedy Symptom/Remedy [Remedy]Close the door. [Symptom]• When the thermal head does not automatically go up after printing, an alarm tone is given. • " " is displayed in the indicator a...

18 11 Set state/Mode LED display Left Point and right Contents of right side LED display Power off Stand-by Print state Paper type setting mode γ -curve set mode ( γ -curve) Paper saving mode Error detect state Power off During data receiving Copy state Number of copies γ -curve No. Standard / High ...

19 12 When the thermal head is dirty with dust and perspiration, etc., white spots or stripes mayappear on the print. In this case, clean the thermal head in the following procedure BYUSING THE SUPPLIED CLEANING PAPER. Roll the cleaning paper and installinto the set. Switch the left side lever to th...

20 13 • Connector JD36SL or equivalent (36 pin)• Input level TTL • Parallel input connector port Signal allocation (Signal : Compatible) PARALLEL DATA INTERFACE Pin No. Return pin No. Signal From/To Function 1 19 STROBE PC/DP Strobe pulse for data reading. Incoming pulse width shoud be0.5 µ s minimu...

23 14 MAINTENANCE Turn off the power for maintenance. Maintenance of Main Unit Wipe off stains of the front panel with a soft cloth.When the panel is heavily stained, wipe of with the clothmoistened with neutral cleanser diluted by water and finish witha dry cloth. Maintenance of Rubber Roller When ...

24 15 SPECIFICATIONS Type: Digital Monochrome Printer Model: P91DW Power supply andpower consumption: 120V AC, 50/60Hz, 1.4A220-240V AC, 50/60Hz, 0.8A Connection terminal: Parallel data interface (36 pin female type) Dot resolution: 1024 x 1024 pixels (Standard)(Max. 1024 x 5120 pixels) Gradation: 2...