Page 2 - Foreword
FX1S Series Programmable Controllers Foreword • This manual contains text, diagrams and explanations which will guide the reader in the correct installationand operation of the FX 1S Ser ies Programmable Controllers. It should be read and understood before attempting to install or use the unit. • Fu...
Page 3 - Hardware Manual; Date
i FX 1S Series Programmable Controllers Hardware Manual This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patentlicenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrialproperty rights which may ...
Page 4 - Guidelines for the Safety of the User and Protection of the FX; This manual provides information for the use of the FX
FX1S Series Programmable Controllers ii Guidelines for the Safety of the User and Protection of the FX 1S . This manual provides information for the use of the FX 1S . The manual has been written to be used by trained and competent personnel. The definition of such a person or persons is asfollows: ...
Page 5 - Notes on the Symbols Used in this Manual
FX1S Series Programmable Controllers iii Notes on the Symbols Used in this Manual At various times throughout this manual cer tain symbols will be used to highlight points whichare intended to ensure the users personal safety and protect the integr ity of equipment.Whenever any of the following symb...
Page 7 - Marine standard; The FX; Standard practice abbreviation
FX1S Series Programmable Controllers v Marine standard The FX 1S Series conforms to the marine standards listed below. Overall, regulation conformity restrictions on various equipment are reduced when the FX 1S Series installation setup complies with marine standards. Please consult with Mitsubishi ...
Page 8 - Note Concerning the CE Marking
FX1S Series Programmable Controllers vi Note Concerning the CE Marking This note does not guarantee that an entire mechanical module produced in accordance withthe contents of this note will comply with the following standards. Compliance to EMC directivea n d LV D d i r e c t i ve o f t h e e n t i...
Page 9 - EMC
FX1S Series Programmable Controllers vii EMC The following products have shown compliance thr ough direct testing (of the identifiedstandards below) and design analysis (through the creation of a technical construction file) tothe European Directive for Electromagnetic Compatibility (89/336/EEC) whe...
Page 10 - series manufactured; Standard; Electromagnetic compatibility
FX1S Series Programmable Controllers viii Models : MELSEC FX 2NC series manufactured from October 1st, 2002 FX 2NC -232ADP FX 2NC -485ADP Standard Remark EN50081-2:1993 Electromagnetic compatibility EN61000-6-4:2007 - Generic emission standard Industrial environment Compliance with all relevant aspe...
Page 11 - LVD
FX1S Series Programmable Controllers ix LVD The following products have shown compliance thr ough direct testing (of the identifiedstandards below) and design analysis (through the creation of a technical construction file) tothe European Directive for Low Voltage (73/23/EEC) when used as directed b...
Page 12 - Associated Manuals
FX1S Series Programmable Controllers x Associated Manuals The following manuals are recommended as essential reference material for the correct operation of aFX 1S series Programmable controller . Manual Name Manual Number Description FX Programming Manual II JY992D88101 This manual contains instruc...
Page 13 - Manual Name
FX1S Series Programmable Controllers xi FX 1N -2AD-BD Users Manual JY992D96201 This manual contains explanation for installation, specification and special auxiliary relay allocation. FX 1N -1DA-BD Users Manual JY992D96401 This manual contains explanation for installation, specification and special ...
Page 14 - MEMO
Page 15 - Table of Contents; FX
xiii Table of Contents Guideline ................................................................................................... ii Associated Manuals ..................................................................................x 1. Introduction.................................................
Page 21 - Introduction; Series Programmable
FX1S Series Programmable Controllers Introduction 1 1-1 1 2 3 4 5 6 7 8 1. Introduction This manual covers the hardware installation instructions for the FX 1S Series Programmable (Logic) Controller. Table 1.1: AC Power, Relay Output Units MODEL INPUT OUTPUT POWER SUPPLY DIMENSIONS mm (inches) MASS ...
Page 23 - Outline Drawing
FX1S Series Programmable Controllers Introduction 1 1-3 1 2 3 4 5 6 7 8 Figure 1.1: FX 1S Outline Drawing Dimensions: mm (inches) The distance between the ver tical centerlines is 8mm (0.32") less than the width of the unit.Please see previous page for each model’s width measurement. w S w T x R...
Page 24 - *1 The communication adapter needs to connect via an FX
FX1S Series Programmable Controllers Introduction 1 1-4 *1 The communication adapter needs to connect via an FX 1N -CNV-BD to the FX 1S Series PLC. Table 1.5: Expansion Board and Communication Adapter MODEL DESCRIPTION POWER SUPPLY (External 24V DC) DIMENSIONS mm (inches) MASS (WEIGHT) kg (lbs) W H ...
Page 25 - Model Name; F X; Unit type
FX1S Series Programmable Controllers Introduction 1 1-5 1 2 3 4 5 6 7 8 1.1 Model Name Table 1.6: Model Table F X 1 S - 1 4 M R - E S / U L C) A)B) D) F) E) A) PLC type: FX 1S B) Total number of I / O channels C) Unit type M MPU - main unit D) Output type R Relay T Transistor E) Features Omit AC Pow...
Page 26 - World Specification
FX1S Series Programmable Controllers Introduction 1 1-6 1.2 World Specification Table 1.7: World / Japanese Specifications Input Sink / Source World spec models: SINK / SOURCEJapanese models: ALWAYS SINK OutputsTransistor World spec models: ALWAYS SOURCEJapanese models: ALWAYS SINK
Page 27 - Serial Numbers; Production year
FX1S Series Programmable Controllers Introduction 1 1-7 1 2 3 4 5 6 7 8 1.3 Serial Numbers Table 1.8: Notes on Serial Numbers 1) Production year 2) Production month 3) Production serial number S E R I A L N O . : 9 X 3 2 6 7 3) 1) 2) e.g. 9=1999 0=2000 1 - 9 = Jan - SeptX = Oct Y = Nov Z = Dec
Page 28 - Configuration
FX1S Series Programmable Controllers Introduction 1 1-8 1.4 Configuration Figure 1.2: Schematic System B A D C H H' E G 1 1' 1 1" 2 F F' FX 1S -10MR-ES/UL FX 1S -14MR-ES/UL FX 1S -20MR-ES/UL FX 1S -30MR-ES/UL FX 1S -10MR-DS FX 1S -14MR-DS FX 1S -20MR-DS FX 1S -30MR-DS FX 1S -10MT-ESS/UL FX 1S -1...
Page 29 - *1 Available for use with FX
FX1S Series Programmable Controllers Introduction 1 1-9 1 2 3 4 5 6 7 8 *1 Available for use with FX 1S version 2.00 or later. *2 When using the FX 1N -EEPROM-8L with an expansion board in group C, only the loader function (transfer program) can be used. Remove it from the PLC after using the loader...
Page 31 - Note; Note for Using Expansion Board; Caution
FX1S Series Programmable Controllers Introduction 1 1-11 1 2 3 4 5 6 7 8 Note When connecting peripheral equipment (programming tool or GOT [direct connection to CPU]) via the FX 1N -232-BD, FX 1N -422-BD, FX 2NC -232ADP or the FX 0N -232ADP, FX 1S main unit should be the following setting condition...
Page 32 - Backup Data; Data Backup; writes to the EEPROM memory. Users may experience; Capacitor backup; Only the RTC is backed up by the capacitor.
FX1S Series Programmable Controllers Introduction 1 1-12 1.5 Backup Data 1.5.1 Data Backup Data includes the Program, Comment, File Register (D1000 ~ D2499), and parameter data.T h i s w i l l b e s t o r e d a s l o n g a s t h e E E P RO M i s n o t d a m a g e d . M i t s u b i s h i E l e c t r ...
Page 33 - Terminal Layouts; The following selection of terminal layouts are taken from the FX
FX1S Series Programmable Controllers Terminal Layouts 2 2-1 1 2 3 4 5 6 7 8 2. Terminal Layouts The following selection of terminal layouts are taken from the FX 1S product range. Note: All layouts are schematic only and are intended to aid in the creation of wiring diagrams. 2.1 FX 1S -**MR-ES/UL F...
Page 37 - Installation Notes; The installation of FX
FX1S Series Programmable Controllers Installation Notes 3 3-1 1 2 3 4 5 6 7 8 3. Installation Notes The installation of FX 1S products has been designed to be safe and easy. When the products associated with this manual are used as a system or individually, they must be installed in asuitable enclos...
Page 38 - Product Outline; PLC
FX1S Series Programmable Controllers Installation Notes 3 3-2 3.1 Product Outline Figure 3.1: Features of the FX 1S PLC Table 3.1: Feature Table 1 Direct Mounting Holes (4.5 mm<0.17"> Diameter) 7 DIN Rail Mounting Clip 2 Input Terminals (24V DC) and Power Supply Terminals 8 Top Cover 3 Out...
Page 40 - General Specifications
FX1S Series Programmable Controllers Installation Notes 3 3-4 3.3 General Specifications Table 3.3: General Specifications *1 The criterion is shown in IEC61131-2. *2 Do not use the PLC under pressure higher than the atmospheric pressure. Doing so may damage the PLC. Item Description Operating Tempe...
Page 41 - PLC Mounting Arrangements
FX1S Series Programmable Controllers Installation Notes 3 3-5 1 2 3 4 5 6 7 8 3.4 PLC Mounting Arrangements To prevent a rise in temperature, mount the units to walls. Never mount them to the floor orceiling of an enclosure. Figure 3.3: PLC Mounting Diagram FX 1S CPU A A A A > 50mm(1.97 inches) A
Page 42 - Use the FX
FX1S Series Programmable Controllers Installation Notes 3 3-6 Caution • Units should not be installed in areas subject to the following conditions: excessive or conductive dust, corrosive gas (salt air, Cl 2 , H 2 S, SO 2 , NO 2 , etc.) or flammable gas, moisture or rain, excessive heat, regular imp...
Page 43 - DO NOT use the “
FX1S Series Programmable Controllers Installation Notes 3 3-7 1 2 3 4 5 6 7 8 • Replace the terminal cover provided, after installation or wiring work is completed, and before supplying power and operating the unit to avoid electric shock. • After reading the manual’s safety instructions, initiate t...
Page 44 - DIN Rail Mounting; UNIT
FX1S Series Programmable Controllers Installation Notes 3 3-8 3.5 DIN Rail Mounting Units can be snap mounted to 35mm(1.37") DIN rail. To release, pull the spring loaded clipsaway from the rail and slide the unit off and up. 3.6 Direct Mounting ∅ = 4.5 mm (0.17") Table 3.4: Hole positions UN...
Page 45 - Hole positions
FX1S Series Programmable Controllers Installation Notes 3 3-9 1 2 3 4 5 6 7 8 ∅ = 4.5 mm (0.17") Table 3.5: Hole positions UNIT mm inches ± 0.2 ± 0.01 B = W FX 0N -232ADP 2- ∅ ( → ) 43 1.70 FX 0N -485ADP C = W-24.5mm (0.97") FX 2NC -232ADP 2- ∅ ( → ) 65.5 2.58 FX 2NC -485ADP FX 0N -232ADP PO...
Page 46 - Termination of Screw Terminals; Ter minal screws should be tightened to between 0.5 to 0.8 N
FX1S Series Programmable Controllers Installation Notes 3 3-10 3.7 Termination of Screw Terminals Ter minal screws should be tightened to between 0.5 to 0.8 N m. Ter minal screws must be secured to prevent a loose connection thus avoiding a malfunction. Failure to do so may causeequipment failures...
Page 47 - Figure 3.5 for installation instructions.; or less
FX1S Series Programmable Controllers Installation Notes 3 3-11 1 2 3 4 5 6 7 8 1) Handle the crimp terminal of the following size when 1 wire is used per terminal. Refer to Figure 3.5 for installation instructions. Figure 3.4: Crimp Terminal for M3 Screws Figure 3.5: Installing 1 wire Per a Terminal...
Page 48 - Figure 3.7 for installation instructions.; Make sure to turn OFF the power before star ting the wiring work.
FX1S Series Programmable Controllers Installation Notes 3 3-12 2) Handle the crimp terminal of the following size when 2 wires are used per terminal. Refer to Figure 3.7 for installation instructions. Figure 3.6: Crimp Terminal for M3 Figure 3.7: Installing 2 Wires Per a Terminal Caution Make sure t...
Page 49 - Installing Optional Units; Expansion Boards; MODEL
FX1S Series Programmable Controllers Installation Notes 3 3-13 1 2 3 4 5 6 7 8 3.8 Installing Optional Units 3.8.1 Expansion Boards The following is a generic explanation of how to install an expansion board onto the FX 1S PLC. For greater detail and specifications of each optional unit, please see ...
Page 50 - • Remove base unit top cover.
FX1S Series Programmable Controllers Installation Notes 3 3-14 Always make sure the power is turned off, before installing a special function board. Only oneboard can be used at one time, do not try to stack multiple boards. A) Special function or optional equipment board. B) Optional equipment conn...
Page 51 - Always make sure the power is turned off, before installing the 5DM.
FX1S Series Programmable Controllers Installation Notes 3 3-15 1 2 3 4 5 6 7 8 3.8.2 FX 1N -5DM Display Module Always make sure the power is turned off, before installing the 5DM. A) Top cover for DMB) Optional equipment connector.C) M3 screw to secure top cover. • Remove the base unit top cover. • ...
Page 53 - Power Supply; Wiring Techniques; Wiring for FX; Wiring Cautions
FX1S Series Programmable Controllers Power Supply 4 4-1 1 2 3 4 5 6 7 8 4. Power Supply 4.1 Wiring Techniques Wiring for FX 1S products has been designed to be safe and easy. If the user is concer ned about the correct installation of these products or associated products, please contact aprofession...
Page 55 - Power Supply Characteristics
FX1S Series Programmable Controllers Power Supply 4 4-3 1 2 3 4 5 6 7 8 4.4 Power Supply Characteristics *1 Includes the input current (5 or 7mA per point). Table 4.2: DC Input Power Requirements, FX 1S -**M*-DS, DSS *1 Includes the input current (5 or 7mA per point). Table 4.1: AC Input Power Requi...
Page 56 - Power Supply Wiring; Figure 4.1: AC Power Supply Example Wiring
FX1S Series Programmable Controllers Power Supply 4 4-4 4.5 Power Supply Wiring Figure 4.1: AC Power Supply Example Wiring ➊ ➌ ➍ ➎ ➏ ➐ ➑ ➒ ➋ ➓ MC L 24V N 0V AC/DC Converter 24+ 24- ➏ 100-240 V AC 50/60 Hz ➊ Power supply 100 - 240V AC, +10% -15%,50/60 Hz ➋ Circuit protector or Fuse ➌ Emergency stop ➍...
Page 57 - Figure 4.2: DC Power Supply Example Wiring
FX1S Series Programmable Controllers Power Supply 4 4-5 1 2 3 4 5 6 7 8 Figure 4.2: DC Power Supply Example Wiring ➊ ➐ ➑ ➒ ➋ ➓ DC/DC Converter 24V DC ➌ ➍ ➎ ➏ MC ➏ ➊ Power supply 24V DC, +10% -15% ➋ Circuit protector or Fuse ➌ Emergency stop ➍ Power supply switch ➎ Power ON pilot indicator ➏ Power su...
Page 58 - Service Power supply; An AC powered FX
FX1S Series Programmable Controllers Power Supply 4 4-6 4.6 Service Power supply An AC powered FX 1S can supply a service current of 24V DC at 400mA. A DC powered FX 1S does not have the capacity to supply a service current. 4.7 Earthing / Grounding Use a cable at least 0.2mm 2 (AWG24) to ground equ...
Page 59 - Inputs; 4V DC Input Specifications; Input Specifications
FX1S Series Programmable Controllers Inputs 5 5-1 1 2 3 4 5 6 7 8 5. Inputs 5.1 24V DC Input Specifications Table 5.1: FX 1S Input Specifications FX 1S Main Unit X0 - X7 X10 - X17 Input voltage 24V DC +10% - 15% Input current 24V DC, 7mA 24V DC, 5mA Input switching current OFF ➔ ON >4.5mA >3.5...
Page 60 - Wiring Diagrams; Input Wiring
FX1S Series Programmable Controllers Inputs 5 5-2 5.2 Wiring Diagrams 5.2.1 Input Wiring Figure 5.1: Input Wiring Diagrams ➊ 24V DC Service Supply ➋ PNP Sensor ➌ NPN Sensor ➍ Input Device Contact ➎ FX 1S Controller Main Body 24V 0V S/S X0 X1 X2 NPN FX 1S -**M*-ES/UL, ESS/UL ➊ ➌ ➍ ➎ FX 1S -Sink FX 1S...
Page 61 - Input Circuit Connection
FX1S Series Programmable Controllers Inputs 5 5-3 1 2 3 4 5 6 7 8 5.2.2 Input Circuit Connection Figure 5.2: Input Circuit Diagrams (Source/Sink) 5.2.3 Diodes and Inputs Connected in Series Figure 5.3: Diode Connection Diagram Voltage drop across the diode is Max. 4V.No more than 2 LEDs should be co...
Page 62 - Resistors and Inputs Connected in Parallel; Parallel resistance Rp: FX; Rb
FX1S Series Programmable Controllers Inputs 5 5-4 5.2.4 Resistors and Inputs Connected in Parallel Parallel resistance Rp: FX 1S = 15k Ω . If resistance Rp is less than the stated value, then add the Rb value using the Equation 1 calculation. Alternatively; Current leakage: FX 1S = 1.5mA. If the cur...
Page 63 - Outputs; Output Specifications; By Relay; None
FX1S Series Programmable Controllers Outputs 6 6-1 1 2 3 4 5 6 7 8 6. Outputs 6.1 Output Specifications Table 6.1: Output Specifications Description Relay Output Transistor Output Switched voltages (resistive load) ≤ 240V AC, ≤ 30V DC 5 - 30V DC Rated current / N points (resistive load) 2A/1 point, ...
Page 64 - Relay Output Example
FX1S Series Programmable Controllers Outputs 6 6-2 6.2 Relay Output Example Figure 6.1: Typical Relay Wiring Diagram ➊ Do not use this terminal ➐ Inductive load ➋ Fuse ➑ Incandescent Lamp ➌ Reverse-current protection diode (See section 6.4) ➒ DC Power Supply ➍ External Mechanical Interlock ➓ AC Powe...
Page 65 - Product life of relay contacts
FX1S Series Programmable Controllers Outputs 6 6-3 1 2 3 4 5 6 7 8 6.2.1 Product life of relay contacts The product life of relay contacts considerably varies depending on the load type used. Takecare that loads generating reverse electromotive force or rush current may cause poor contactor depositi...
Page 66 - Load capacity
FX1S Series Programmable Controllers Outputs 6 6-4 Table 6.2: The product life of relay contacts becomes considerably shor ter than the above conditionswhen the rush overcurrent is shut down. * For countermeasures while using inductive loads, refer to "Output circuit configuration" below in ...
Page 67 - Output circuit configuration
FX1S Series Programmable Controllers Outputs 6 6-5 1 2 3 4 5 6 7 8 6.2.2 Output circuit configuration An internal protection circuit for the relays is not provided in the relay output circuit for thisproduct. It is recommended to use inductive loads with built-in protection circuits. When usingloads...
Page 68 - Bad
FX1S Series Programmable Controllers Outputs 6 6-6 3) Interlock 4) In-phase For loads such as forward/reverse contactors, etc.,where a hazardous condition could result if switchedON simultaneously, an external interlock should bep r o v i d e d f o r i n t e r l o c k i n g t h e P L C ' s i n t e r...
Page 69 - Transistor Output Examples; Figure 6.2: Transistor Output Wiring Diagram
FX1S Series Programmable Controllers Outputs 6 6-7 1 2 3 4 5 6 7 8 6.3 Transistor Output Examples Figure 6.2: Transistor Output Wiring Diagram Figure 6.3: Japanese Model Transistor Output ➊ Do not use this terminal ➋ Emergency Stop ➌ Fuse ➍ External Mechanical Interlock (See Section 6.4) ➎ DC Power ...
Page 70 - Response Times; Dummy load
FX1S Series Programmable Controllers Outputs 6 6-8 6.3.1 Response Times OFF times increase as the load current decreases.For improved response times use a 'dummy' resistor, see Figure 6.4. If a response time of 0.5ms or better is required when using 'light loads' use a 'dummy' resistor and ensure th...
Page 71 - External wiring precaution; ) Contact protection circuit for inductive loads
FX1S Series Programmable Controllers Outputs 6 6-9 1 2 3 4 5 6 7 8 6.3.2 External wiring precaution 1) Contact protection circuit for inductive loads Transistor outputs use inter nal zener diode (50V)as protection circuitr y. When driving the inductivel o a d w i t h t r a n s i s t o r o u t p u t ...
Page 73 - Diagnostics; Preliminary Checks; Check power supply, ground and I/O cables are wired correctly.
FX1S Series Programmable Controllers Diagnostics 7 7-1 1 2 3 4 5 6 7 8 7. Diagnostics 7.1 Preliminary Checks Table 7.1: Preliminary Checks Check power supply, ground and I/O cables are wired correctly. Turn the power supply on. Check that the power LED is lit. Down load a small test program to the P...
Page 74 - Fault; LED OFF; LED is lit; Remedy
FX1S Series Programmable Controllers Diagnostics 7 7-2 7.2 ERROR LED ON (CPU ERROR) Table 7.2: Error LED Checks Fault ERROR LED ON Remedy Reset PLC. Turn power OFF, then ON and trigger RUN input. Possible results LED OFF Has the memory cassette been installed or removed while the unit was still powe...
Page 75 - Common Errors; Corroded contact points at some point in an I/O line.; Maintenance; Check interior temperature of the panel.
FX1S Series Programmable Controllers Diagnostics 7 7-3 1 2 3 4 5 6 7 8 7.3 Common Errors - Corroded contact points at some point in an I/O line. - An I/O device has been used outside its specified operating range. - An input signal occurs in a shor ter time period than that taken by one program scan...
Page 76 - Operation and Error Flags
FX1S Series Programmable Controllers Diagnostics 7 7-4 7.5 Operation and Error Flags Table 7.3: Operation and Error Flags Parallel link error Parameter error Syntax error Program (circuit) error Program execution error Execution error latch M8063 (ref. D8063) M8064 (ref. D8064) M8065 (ref. D8065, D8...
Page 77 - PLC Status Registers; Watchdog timer
FX1S Series Programmable Controllers Diagnostics 7 7-5 1 2 3 4 5 6 7 8 7.6 PLC Status Registers Table 7.4: PLC Status Registers 02H=EEPROM protect switch OFF0AH=EEPROM protect switch ON10H=MPU memory D8000 (default 200msec) D8001 D8002 D8003 D8004 Watchdog timer PLC version 22100 = FX 1S Version 1.0...
Page 78 - Error Registers; Error code for PLC hardware error
FX1S Series Programmable Controllers Diagnostics 7 7-6 7.7 Error Registers Table 7.5: Error Registers D8061 D8063 D8064 D8065 D8066 D8067 D8068 D8069 Error code for PLC hardware error Error code for parallel link fault Parameter error code Syntax error code Program (circuit) error code Program execu...
Page 79 - Error Codes
FX1S Series Programmable Controllers Diagnostics 7 7-7 1 2 3 4 5 6 7 8 7.8 Error Codes Table 7.6: Error Codes D8061 No error 0000 RAM error 6101 Operation circuit error 6102 D8063 Check both power andcommunications connections No error 0000 Parity/overrun/framing error 6301 Character error 6302 Data...
Page 80 - Instruction List
FX1S Series Programmable Controllers Diagnostics 7 7-8 7.9 Instruction List Table 7.7: Numerically Sorted 000 010 020 030 040 050 060 070 080 TRANSFERS, COMP PROGRAM FLOW +- ×÷ , LOGICS SHIFT DATA OPERATION 1 HIGH-SPEED HANDY INSTR. 1 FX I/O DEVICES FX SERIAL DEVICES 0 CJ CMP ADD ZRST REF IST RS 1 C...
Page 81 - Symbol
FX1S Series Programmable Controllers Diagnostics 7 7-9 1 2 3 4 5 6 7 8 Table 7.8: Alphabetically sorted A Symbol ABS ABSD ADD AND
ASCI FNC No. 155 062 020 066 232-238 082 D P B BCD BIN BMOV 018 019 015 CALL CCD 010 084 C CJ CMP 000 001 DEC DECO 025 041 D DI DIV DRVA 005 023 159 E DRVI DSW 158 072 ...
Page 83 - Device List; Device Type
FX1S Series Programmable Controllers Diagnostics 7 7-11 1 2 3 4 5 6 7 8 7.10 Device List Table 7.9: Device List Device Type Specification Remarks Program capacity 2k steps by FX1S internal EEPROM or 2k steps by FX 1N -EEPROM-8L I/O configuration Max total I/O set by Main Processing Unit Auxiliary re...
Page 86 - Constants
FX1S Series Programmable Controllers Diagnostics 7 7-14 Constants Decimal K 16 bit: -32,768 to +32,767 32 bit: -2,147,483,648 to +2,147,483,647 Hexadecimal H 16 bit: 0000 to FFFF 32 bit: 00000000 to FFFFFFFF Device Type Specification Remarks
Page 87 - Discontinued model
FX1S Series Programmable Controllers Discontinued model 8 8-1 1 2 3 4 5 6 7 8 8. Discontinued model The table below shows discontinued models of MELSEC-F Series PLCs described in this manual. Discontinued model Production stop date Repair acceptance period FX 0N -232ADP January 31, 2006 Until Januar...
Page 92 - Specifications are subject to change without notice.; HARDWARE MANUAL
HEAD OFFICE: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPANHIMEJI WORKS:840, CHIYODA CHO, HIMEJI, JAPAN JY992D83901L(MEE) Effective June 2009 Specifications are subject to change without notice. HARDWARE MANUAL FX 1S SERIES PROGRAMMABLE CONTROLLERS MODEL FX1S-HW-E MODEL CODE 09R...
