Mitsubishi Electric F920GOT-BBD-K-E - Manual

F920GOT-BBD5-K-E

F920GOT-BBD-K-E

Installation Manual

JY997D02201G

This manual contains text, diagrams and explanations which will guide the reader in the correct installation, safe use and
operation of the F920GOT-BBD5-K-E, F920GOT-BBD-K-E and should be read and understood before attempting to
install or use the unit. Fur ther information can be found in the associated manuals list below.
Specifications are subject to change without notice

Guidelines for the Safety of the User and Protection of the F920GOT-BBD5-K-E,
F920GOT-BBD-K-E

This manual has been written to be used by trained and competent personnel. The definition of such a person or persons
is as follows:

a)

Any engineer using the product associated with this manual, should be of a competent nature, trained and
qualified to the local and national standards. These engineers should be fully aware of all aspects of safety with
regards to automated equipment.

b)

Any commissioning or service engineer must be of a competent nature, trained and qualified to the local and
national standards.

c)

All operators of the completed equipment (see note) should be trained to use that product in a safe manner in
compliance to established safety practices.

Note:

The term ‘completed equipment’ refers to a third par ty constructed device which contains or uses the product
associated with this manual.

Note’s on the Symbols Used in this Manual

At various times through out this manual cer tain symbols will be used to highlight points of information which are intended
to ensure the users personal safety and protect the integrity of equipment.

1)

Indicates that the identified danger

WILL

cause physical and proper ty damage.

2)

Indicates that the identified danger could

POSSIBLY

cause physical and proper ty damage.

•

Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise
as a result of the installation or use of this equipment.

•

All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to
guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these
illustrative examples.

•

Please contact a Mitsubishi Electric distributor for more information concerning applications in life critical situations
or high reliability.

Associated Manuals

~

Necessar y manual

|

Either manual is necessary.

Refer to the manual of the connected programmable controller for fur ther details concerning that unit.

Manual Name

Manual Number

Description

|

F920GOT-BBD5-K-E,
F920GOT-BBD-K-E
Installation Manual

JY997D02201

(This manual)

Describes the hardware such as specifications, wiring and
installation of the F920GOT-BBD5-K-E and F920GOT-BBD-
K-E.

~

GOT-F900
OPERATION MANUAL
(describes GT Designer2)

JY997D09101

(separate volume)

Describes the operation and use of the GOT-F900 Series
graphic operation terminals and GT Designer2.

~

GOT-F900 Series
Operation Manual

JY992D94701

(separate volume)

Describes the operation and use of the GOT-F900 Series
graphic operation terminals, GT Designer and FX-PCS-DU/
WIN-E.

~

GOT-F900 Series
Hardware Manual
(connection diagram)

JY992D94801

(separate volume)

Describes wiring and installation of the GOT-F900 Series
graphic operation terminals.

|

SW

…

D5C-GOTR-PACK

Operating Manual

(included with screen
creation software)

Describes the operating procedures of the screen creation
software. (See the HELP file in the software.)

|

GT Designer2 Version 1
Operating Manual

(PDF files on CD-ROM
included with screen
creation software)

Describes the operation method of GT Designer2
(SW

…

D5C-GTD2-J), data transfer to the GOT-900 Series,

etc.

|

GT Designer2 Version 1
Reference Manual

(PDF files on CD-ROM
included with screen
creation software)

Describes the specifications, contents of setting, etc. of
each object function used in GT Designer2 (SW

…

D5C-

GTD2-J).

|

FX-PCS-DU/WIN-E
SOFTWARE MANUAL

JY992D68301

(included with screen

creation software)

Describes the operation of FX-PCS-DU/WIN-E screen
creation software.

1. Introduction

1)

The F920GOT-BBD5-K-E and F920GOT-BBD-K-E (hereafter called “GOT”)
a r e t o b e m o u n t e d o n t h e fa c e o f a c o n t r o l o r o p e r a t i o n s p a n e l , a n d
connected to the programming por t (CPU por t) of a PLC.

2)

Various devices can be monitored and PLC data changed through the
screens in the GOT.

3)

Using PLC programming software, FX Series PLC user programming can be
uploaded, downloaded and monitored via the GOT.

4)

The F920GOT-BBD5-K-E is driven by 5V DC power supply (from the PLC
through a communication cable). The F920GOT-BBD-K-E is driven by a 24V
DC power supply.

5)

The F920GOT-BBD5-K-E can be connected to the FX, A, QnA and Q Series
PLC.
The F920GOT-BBD-K-E can be connected to the FX, A, QnA and Q Series
PLC, PLC manufactured by another company and micro computer board.

For fur ther details concer ning applicable PLCs and connections to the PLC, refer to the GOT-F900 Ser ies Hardware
Manual (Connection Diagram) offered as a separate volume.

1.1 Product Lists

GOT Main Unit

Optional communication cable

•

In addition to the connections shown above, the F920GOT-BBD5-K-E can be connected to the A, QnA and Q Series
PLC, and the F920GOT-BBD-K-E can be connected to via computer link to a PLC manufactured by Mitsubishi, PLC
manufactured by another manufacturers and micro computer board.
For fur ther details concer ning connectable equipment and communication cables, refer to the GOT-F900 Ser ies
Hardware Manual [Connection] offered as a separate volume.

Optional screen creation software

Caution

D u r i n g a b n o r m a l c o m m u n i c a t i o n ( i n c l u d i n g c a b l e b r e a k a g e ) w h e n m o n i t o r i n g w i t h i n t h e G OT,
communication between the GOT and programmable controller CPU is interrupted and it is impossible to
operate keys or devices in the PLC via the GOT.
Communication and operation resumes when the GOT system is correctly configured.
DO NOT configure the emergency stop or safety features through the GOT, and be sure that there will be
no adverse consequences in the event of a GOT - PLC communications malfunction.

Note

•

Do not lay signal cables near high voltage power cables or allow them to share the same trunking duct.
Otherwise effects of noise or surge induction are likely to occur. Keep a safe distance of more than 100
mm away from these wires.

•

Operate switches on the panel by hand.
DO NOT use excessive force, or attempt to operate them with hard or pointed objects.
The tip of a screw driver, pen or similar objects for example may break the screen.

Connectable PLC units differ for the F920GOT-BBD5-K-E and the F920GOT-BBD-K-E.
Fur ther information can be found in GOT-F900 series Hardware Manual [Connection].

Product Name

Model Name

Specifications

Graphic Operation Terminal

F920GOT-BBD5-K-E

Graphic operation terminal main unit

F920GOT-BBD-K-E

Graphic operation terminal main unit

Product

Name

Classification

Model Name

Specifications

PLC
connection
cable

F920GOT-
BBD5-K-E

FX-50DU-CAB0

3m (9’10”) Communication cable (GOT

↔

CPU por t in FX

0S

,

FX

1S

, FX

0N

, FX

1N

, FX

2N

or FX

2NC

series PLC)

Cable length is 3m (9' 10").
Use FX-50DU-CAB0/EN for compliance to EC EMC.

FX-50DU-CAB0/EN

3m (9’10”)

FX-50DU-CAB0-1M

1m (3’3”)

F920GOT-
BBD-K-E

FX-50DU-CAB0

3m (9’10”) Communication cable (GOT

↔

CPU por t in FX

0S

,

FX

1S

, FX

0N

, FX

1N

, FX

2N

or FX

2NC

series PLC)

(**M is cable length 1M:1m(3’3”), 10M:10m(32’9”),
20M:20m(65’7”), 30M:30m(98’5”).
Use FX-50DU-CAB0/EN for compliance to EC EMC.

FX-50DU-CAB0/EN

3m (9’10”)

FX-50DU-CAB0-**M

Described

on right

FX-40U-CAB

3m (9’10”) Communication cable (GOT

↔

CPU por t in A, QnA

series PLC)
(**M is cable length 10M:10m(32’9”),
20M:20m(65’7”), 30M:30m(98’5”).

FX-40DU-CAB0-**M

Described

on right

QC30R2

3m (9’10”)

Communication cable (GOT

↔

CPU por t in Q series

PLC)

Screen data
transfer
cable

F920GOT-
BBD5-K-E
and F920GOT-
BBD-K-E

FX-232CAB-1

3m (9’10”)

Data exchange cable (GOT

↔

Personal computer

<9-pin D-sub>)

Product

Name

Model Name

Specifications

For F920GOT-
BBD5-K-E and
F920GOT-BBD-
K-E

GT Designer 2
SW

…

D5C-GTD2-E (

…

indicates the version.)

Software for GOT-F900 and GOT-A900 Series (for Windows)
In F920GOT-BBD5-K-E, SW1D5C-GTD2-E Version 1.00A or later is
available.
In F920GOT-BBD-K-E, SW1D5C-GTD2-E Version 1.02C or later is
available.

F920GOT-BBD5-
K-E

GT Designer
SW

…

D5C-GOTR-

PACKE (

…

indicates the

version.)

Software for GOT-F900 and GOT-A900 Series (for Windows)
SW5D5C-GOTR-PACK-E SW5-26C version (Version 5.26C) or later

FX-PCS-DU/WIN-E

Software for GOT-F900 Series (for Windows)
SW0PC-FXDU/WIN-E Version 2.70 or later

PLC

Programming

port

GOT

1.2 Dimensions and Each Part Name [Both F920GOT-BBD5-K-E and F920GOT-BBD-K-E

(Power terminals is excluded).]

Dimensions: mm (inches)

Mass (Weight):

0.3 kg (0.66 lbs)

Accessory:

Mounting brackets, Tightening bolt (M4, 4 bolts), Packing seal for dust and water resistance

1)

Front panel
a) Display

b) Function keys

c) Cursor keys

d) 0 to 9 keys

2)

Rear panel
e) Mounting bracket and tightening bolt (accessor y)
f) Power terminals (Not provided for the F920GOT-BBD5-K-E)
g) Communication ports

h) Communication cable (optional)
i) Packing seal (accessory)

2. Specifications

2.1 General Specifications (F920GOT-BBD5-K-E and F920GOT-BBD-K-E)

2.2 Power Supply Specifications

Port

Description

COM0 RS-422

RS-422 por t for connecting PLC (FX, A, QnA) <9-pin D-sub>

COM1 RS-232C

RS-232C por t for connecting a personal computer or PLC (Q) <9-pin D-sub>

Item

Specifications

Operating Temperature

0 ~ 50 °C (32 ~ 122 °F)

Storage Temperature

-20 ~ 60 °C (-4 ~ 140 °F)

Humidity

35 ~ 85% Relative Humidity, No condensation

Operating atmosphere

Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of
electroconductive dust par ticles and must be no direct sunlight. (Same as for saving)

Vibration Resistance
- inter mittent vibration

10 ~ 57 Hz: 0.075 mm Half Amplitude
57 ~ 150 Hz: 9.8 m/s

2

Acceleration

Sweep Count for X, Y, Z: 10 times (80 min. in each direction)

Vibration Resistance
- Continuous vibration

10 ~ 57 Hz: 0.035 mm Half Amplitude
57 ~ 150 Hz: 4.9 m/s

2

Acceleration

Sweep Count for X, Y, Z: 10 times (80 min in each direction)

Shock Resistance

147m/s

2

Acceleration,

3 times in each direction X, Y, and Z

Noise Immunity

1000 Vp-p, 1

µ

second, 30 ~ 100 Hz, tested by noise simulator

Dielectric Withstand
Voltage

500 V AC > 1 min, tested between power terminals and ground

Insulation Resistance

5 M

Ω

> at 500 V DC, tested between power terminals and ground

Protection

IP65f level (Front panel only)

Model Name

Specifications

F920GOT-
BBD5-K-E

Supply voltage

: 5V DC ±5% (supplied from PLC through communication cable)

Current consumption

: 220mA/5V DC while backlight is ON, 180mA/5V DC while backlight is OFF

F920GOT-
BBD-K-E

Supply voltage

: 24V DC+10%-15% (externally supplied through power terminals)

Power ripple

: 220 mV or less

Current consumption

: 80mA/24V DC while backlight is ON, 70mA/24V DC while backlight is OFF

Fuse

: Built-in (It cannot be replaced.)

Allowable instantaneous power interruption:

Less than 5 ms (Continuous operation is assured.)

Grounding

: Grounding resistance: 100

Ω

or less

35.5(1.40")

5(0.20")

106(4.17")

134(5.28")

a)

b)

d)

c)

118(4.65")

90(3.54")

5(0.20") or less

e)

g)

i)

h)

COM1 RS232C

COM0 RS422

f)

Front panel

Rear panel (with mounting bracket and tightening bolt)