Mitsubishi Electric 56P-QF60LCU - Manual

Page 2 - Index; CAUTION; TO REDUCE THE RISK OF ELECTRIC SHOCK,

Index Important safeguards................................................................................................................................................. 3Contents .........................................................................................................................

Page 3 - Important safeguards

EN-3 Important safeguards Please read all these instructions regarding your monitor and retain them for future reference. Follow all warnings and instruc-tions marked on the monitor. 1. Read instructions All the safety and operating instructions should be read be-fore the appliance is operated. 2. R...

Page 5 - Contents

EN-5 COMPLIANCE NOTICE OF FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial ...

Page 6 - Parts Name and Functions; Front panel

EN-6 MENU EXIT (7) (6) (5) (4) (3) (2) (8) (1) Parts Name and Functions (1) POWER button ( ) Switches the power on/off. (2) MENU button Activates the menu when the menu is turned-off. (3) PLUS (+) button Acts as (+) button to increase the adjustment with menu. (4) MINUS (-) button Acts as (-) button...

Page 7 - Rear panel

EN-7 RS-232C LAN INPUT1 INPUT2 INPUT3 INPUT4 POWER DVI-D (1) (2) (3) (4) (5) (1) Main Power Switch On/Off Switch to turn main power on/off. (2) AC IN connector Connects with the power cord. (3) INPUT 1 - 4 (DVI-D x 4) Connect the DVI-D cable with the DVI-D connector of the computer. (4) RS-232C conn...

Page 8 - Installation; Be sure to follow the directions below.

EN-8 Installation Warning: Be sure to follow the directions below. This product requires special installation to prevent falling or toppling.Please ask installation specialists for installation.Don't attempt to install the product by yourself. Determine the installation location CAUTION: DO NOT ATTE...

Page 9 - Connections; Before making connections:; Connect the power cord

EN-9 Connections Before making connections: • First turn off the power of all the attached equipment and make connections.• Refer to the user manual included with each separate piece of equipment. DVI-D cable Computer 56P-QF60LCU(Rear panel) DVI-D INPUT1 INPUT2 INPUT3 INPUT4 DVI-D Recommended video ...

Page 10 - Basic operation

EN-10 Basic operation Power ON procedures 1. Turn the Main Power Switch on the rear of the product to ON to turn on the main power. The power lamp blinks green and then illuminates red. (You cannot turn on the power while the lamp is blinking green.) 2. Press the power ( ) button to turn on the powe...

Page 11 - Troubleshooting; Others

EN-11 Troubleshooting Consult the following table for troubleshooting a problem. Symptom Cause and remedy Reference page The monitor displays nothing. (The power lamp doesn't illuminate.) Check that the power cord is connected securely. P.9 Using other device, check that the wall outlet is receiving...

Page 12 - Speci

EN-12 *1 Viewing angle: Angle at which images are displayed at a white-to-black contrast level of 30 or higher. *2 Average of the response speeds between certain gradation levels (for example, 0, 63, 127, 191, 255) PC input Operational environment Storageenvironment Weight Accessories Gross Outline ...

Page 13 - Pin Assignment

EN-13 1) INPUT 1 - 4 PIN No. Name PIN No. Name 1 TX 2- 13 NC 2 TX 2+ 14 +5V Power 3 Shield (TX2/TX4) 15 Ground 4 NC 16 Hot Plug Detect 5 NC 17 TX 0- 6 DDC-Serial Clock 18 TX 0+ 7 DDC-Serial Data 19 Shield (TX0/TX5) 8 NC 20 NC 9 TX 1- 21 NC 10 TX 1+ 22 Shield (TXC) 11 Shield (TX1/TX3) 23 TXC + 12 NC ...

Page 14 - MITSUBISHI ELECTRIC CORPORATION

871D502A10 Printed in Japan 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan MITSUBISHI ELECTRIC CORPORATION