Mitsubishi DLP UD8900U- User Manual
Mitsubishi DLP UD8900U– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – To connect with one projector:
- Page 3 – You can assign the ID code to the control command.
- Page 4 – Control command configuration; Code unique to each control operation.; the receiving order; • NAK return; before sending a next command.
- Page 7 – Execution procedure of RS-232C commands via LAN; • You can skip the certification process by
- Page 9 – Use the following commands to obtain other information.
- Page 10 – Remote cont rol key commands; (Not executable in stand-by mode. When the remote control key
- Page 11 – Direct commands; How to set the value; Use the character or ASCII code as shown below to set the value.
- Page 12 – Function commands; screen is being displayed, the splash screen is only canceled.); Menu setting commands
- Page 15 – PROJECTOR ID
- Page 19 – Password lock commands; • When ID is not specified:
1
DLP™ Projector
UD8900U/UD8850U
Controlling the projector via RS-232C connection
Contents
1. Introduction ............................................................................................................ 2
1.1 Connection ............................................................................................................................... 2
1.2 Interface ................................................................................................................................... 3
1.2.1 Pin assignment of SERIAL terminal (D-SUB 9-pin) .............................................................................. 3
1.2.2 Communications format ...................................................................................................................... 3
2. Control command configuration ............................................................................ 4
3. Control sequence ................................................................................................... 4
4. Execution procedure of RS-232C commands via LAN .......................................... 7
5. Command list ......................................................................................................... 8
5.1 General control commands ...................................................................................................... 8
5.2 Reading commands ................................................................................................................. 8
5.2.1 Status read commands ........................................................................................................................ 8
5.2.2 Read commands for items in INFORMATION menu ............................................................................ 9
5.2.3 Read commands for other information ................................................................................................ 9
5.3 Remote control key commands ............................................................................................. 10
5.4 Direct commands ................................................................................................................... 11
5.5 Function commands .............................................................................................................. 12
5.6 Menu setting commands ....................................................................................................... 12
5.6.1 IMAGE menu ...................................................................................................................................... 12
5.6.2 INSTALLATION 1 menu ...................................................................................................................... 13
5.6.3 INSTALLATION 2 menu ...................................................................................................................... 13
5.6.4 MULTI-SCREEN menu ....................................................................................................................... 14
5.6.5 FEATURE menu .................................................................................................................................. 15
5.6.6 SIGNAL menu .................................................................................................................................... 16
5.6.7 NETWORK menu ............................................................................................................................... 16
5.7 Password lock commands ..................................................................................................... 19
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 1. Introduction This projector can be controlled by connecting a personal computer with RS-232C terminal.In addition, by connecting multiple projectors to each other in a daisy chain configuration, you can control each projector from one personal computer. PC-controllable functions: • Turning the ...
3 • Example of ID setting (When Group A, which performs multi-projection with two projectors, and Group B, which performs multi-projection with three projectors, are connected.) Projector 1 PROJECTOR ID : 01 GROUP ID : A Multi-projection Group A Projector 2 PROJECTOR ID : 02 GROUP ID : A Projector 3...
4 2. Control command configuration The command consists of the address code, ID code, function code, data code, ACK/NAK, and end code. The length of the command varies among the functions. Address code ID code Function code Data code ACK/NAK End code ASCII code ‘30h’ ‘30h’ ‘3Bh’ ID ‘3Bh’ Function Da...
