Mitsubishi DLP UD8900U- Manuals

Page 2 - To connect with one projector:

2 1. Introduction This projector can be controlled by connecting a personal computer with RS-232C terminal.In addition, by connecting multiple projectors to each other in a daisy chain configuration, you can control each projector from one personal computer. PC-controllable functions: • Turning the ...

Page 3 - You can assign the ID code to the control command.

3 • Example of ID setting (When Group A, which performs multi-projection with two projectors, and Group B, which performs multi-projection with three projectors, are connected.) Projector 1 PROJECTOR ID : 01 GROUP ID : A Multi-projection Group A Projector 2 PROJECTOR ID : 02 GROUP ID : A Projector 3...

Page 4 - Control command configuration; Code unique to each control operation.; the receiving order; • NAK return; before sending a next command.

4 2. Control command configuration The command consists of the address code, ID code, function code, data code, ACK/NAK, and end code. The length of the command varies among the functions. Address code ID code Function code Data code ACK/NAK End code ASCII code ‘30h’ ‘30h’ ‘3Bh’ ID ‘3Bh’ Function Da...

Page 7 - Execution procedure of RS-232C commands via LAN; • You can skip the certification process by

7 4. Execution procedure of RS-232C commands via LAN • When you use the LAN function, set the STANDBY MODE to STANDARD or LAN. • When you execute RS-232C commands via LAN, check that the CONTROL SYSTEM in the NETWORK menu is set to STANDARD. • You can change the certification password using the NETW...

Page 9 - Use the following commands to obtain other information.

9 5.2.2 Read commands for items in INFORMATION menu Use the following commands to obtain the values of the items in the INFORMATION menu. ITEM Function Data (Receive) Character ASCII code LAMP 1 TIME (LOW) vLE1L 76h 4Ch 45h 31h 4Ch hhhhmm LAMP 2 TIME (LOW) vLE2L 76h 4Ch 45h 32h 4Ch hhhhmm LAMP illum...

Page 10 - Remote cont rol key commands; (Not executable in stand-by mode. When the remote control key

10 [Example] When checking the currently selected input terminal (when the INPUT VIDEO is being selected). (Values enclosed in quotation marks are ASCII codes.): • Command sent from the PC, etc. Status code returned from the projector Description ‘30’ ‘30’ ‘76’ ‘49’ ‘0D’00vl Command for checking the...

Page 11 - Direct commands; How to set the value; Use the character or ASCII code as shown below to set the value.

11 [Example] When displaying the MENU selection bar. (Values enclosed in quotation marks are ASCII codes.): • Command sent from the PC, etc. Status code returned from the projector Description ‘30’ ‘30’ ‘72’ ‘35’ ‘34’ ‘0D’00r54 Command operating the same as the MENU button (ID command is omitted.) ‘...

Page 12 - Function commands; screen is being displayed, the splash screen is only canceled.); Menu setting commands

12 5.5 Function commands (Not executable in stand-by mode. When the mute commands are sent while the splash screen is being displayed, the splash screen is only canceled.) ITEM Function Data Character ASCII code BLANK MUTE 4Dh 55h 54h 45h 0 (OFF), 1 (ON) SPLIT SPLT 53h 50h 4Ch 54h 0 (OFF), 1 (ON) FR...

Page 15 - PROJECTOR ID

15 ITEM Function Data Character ASCII code COLOR MATCHING-MANUAL (RESET) MNRST 4Dh 4Eh 52h 53h 54h COLOR MATCHING--MEASURE-MEASURED DATA (Y(Relative value)) MSML 4Dh 53h 4Dh 4Ch x00050 to 20000 x: Color selectionR (RED), G (GREEN), B (BLUE), W (WHITE) COLOR MATCHING--MEASURE-MEASURED DATA (x) MSMX 4...

Page 19 - Password lock commands; • When ID is not specified:

19 5.7 Password lock commands The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password lock is enabled or disabled successfully, the ...

Mitsubishi DLP UD8900U- Manuals

Manuals:

User Manual Mitsubishi DLP UD8900U

Summary

Mitsubishi Manuals