Miller GP30 - Manual - manualsarea.com

Page 2 - Carry loads as low as possible; TO PREVENT POSSIBLE PERSONAL INJURY, OBSERVE THE FOLLOW-; DANGER

TO PREVENT POSSIBLE ROLLOVER, OBSERVE THE FOLLOWING SAFETY PRECAUTIONS ♦ Carry loads as low as possible ♦ Drive tractor slowly when turning, operating on hills or inclines, or traversing un- even ground ♦ Raise load to full height only when tractor in on even ground and front wheels are straight ahe...

Page 3 - TABLE OF CONTENTS

TABLE OF CONTENTS • Composite Bearing Information • Mounting Loader on Tractor • Dismounting Loader • Quick-attach Instructions • Parts Schematics • Cylinder Packing Detail • Loader Specifications • Warranty SERIAL No. of Loader Purchased _______________________ Date Purchased____________________

Page 4 - COMPOSITE BEARING INFORMATION

COMPOSITE BEARING INFORMATION FIGURE A . Your GP/GL-Series loader is equipped with composite, greaseless bearings at all (12) pivot points. These high-quality bearings should not be confused with plastic bushings, sintered bushings, or metal-backed bearings. Composite bearings are made from an ultra...

Page 5 - MOUNTING LOADER; STEP 1

MOUNTING LOADER STEP 1 For a new loader installation, the mountings must be installed on the tractor first. Refer to the typical mounting kit shown in Figure 1. A detailed schematic of your specific kit is available—just call 1-800-570-8205 if the schematic was not included with your new loader. STE...

Page 6 - DISMOUNTING LOADER; STEP 2

DISMOUNTING LOADER STEP 1 DRIVE THE TRACTOR ONTO FLAT CONCRETE and place the loader in the position shown in Fig 1. STEP 2 Remove the stand legs from their stored position and place them in their dismount position. Slide the in- ner tubes down to the extended position and secure them with the 3/4” p...

Page 7 - QUICK-ATTACH INSTRUCTIONS; UNCOUPLING; COUPLING

QUICK-ATTACH INSTRUCTIONS UNCOUPLING 1. Raise sliding latches as shown in Figure 1. 2. Rotate QT pins out of the lower notches, raise, and then rotate them into the upper notches of the sliding latches as shown in Figure 2. 3. Slide the sliding latches down as shown in Figure 3. This secures the QT ...

Page 8 - SCHEMATIC

1 8 15 19 29 10 15 19 16 14 17 30 36 27 28 13 12 35 3 26 18 2 11 9 31 32 29 34 33 29 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 MF30 MAINFRAME, GL30/GP30 1 2 QT30 QUICK ATTACH FRAME 1 3 CY-059 CYLINDER, BUCKET, GL/GP30 2 8 PN-600AC16 PIN, CHROME 2" x 6" WITH RETAINER 2 9 PN-700AC16 PIN, CHROME ...

Page 10 - SLIDING LATCH DETAIL

ITEM NO. PART NUMBER DESCRIPTION Pin Up Latch Up/QTY. 1 QT02-01L SLIDING LATCH ASSY, QT, LH 1 2 QT02-01R SLIDING LATCH ASSY, QT, RH 1 3 QT02-14 RETAINING PIN ASSEMBLY, QT 2 4 QT30-W WELDED QT FRAME 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 4 HW-NS-06-A NUT, 3/8-16 UNC, CL, ZN 4 5 HW-SP-01 SPRING, QT H...

Page 17 - ROD WIPER; PISTON; SNAP RING; FRONT OF CYLINDER

ROD WIPER PISTON GLAND SEAL, U-CUP, LARGE SEAL, U-CUP, SMALL O-RING, SMALL O-RING, LARGE B/U WASHER SNAP RING SCHEMATIC DWG. NO. SHEET REV. DATE PACKING CONFIGURATION, U-CUP OF 1 A 1/13/2005 CP-KT-U 1 WEIGHT: FRONT OF CYLINDER

Page 18 - GP30 SPECIFICATIONS

14’−8" 13’−6" 2’−11" 34° 44° 11’−10" 8" 100" TYPICAL GP30 SPECIFICATIONS SPECIFICATIONS AND PERFORMANCE NUMBERS ARE FOR REFERENCE ONLY WEIGHTS: Loader (less bucket and mounts) : 2090 lbs. 8 FT Bucket : 800 lbs. Mounting Kit (Typical) : 710 lbs. Total : 3600 lbs. LIFTING CAPAC...

Page 19 - WARRANTY

WARRANTY Dec 2004 ALL PRODUCTS MANUFACTURED BY MILLER LOADERS, INCOPRORATED ( MLI ) EXCEPT THE CHROME-PLATED PIVOT PINS USED ON GREASELESS LOADERS, ARE GUARENTEED TO THE ORIGINAL PURCHASER FOR A PERIOD OF ONE YEAR FROM THE DAY OF PURCHASE AGAINST ANY DEFECTS IN MATERIALS AND WORKMANSHIP OF FARM LOAD...

Miller GP30 - Manual

Table of Contents:

Summary

Other Miller Models