Miele WT 2670 - Manual

The machine is built in accordancewith current safety requirements. Unauthorised repairs could result inunforeseen dangers for the user, forwhich the manufacturer cannot acceptliability. Repairs should only beundertaken by a Miele approvedtechnician.Ensure current is not supplied to themachine until...

Control panel a Start/Stop button For starting the programme selectedand cancelling a programme once ithas started. b Display with – , OK, + andLoad/Detergent buttons See the following page for moredetails. c m button For selecting delay start andsetting the time of day. d PC / Optical interface Thi...

Display When a programme is selected thedisplay can be used to select andchange programme parameters. - / + buttons For altering the parameters highlightedin the display: - decreases the parameter or moves the highlighting upwards + increases the parameter or moves the highlighting downwards. OK but...

Before using the machine for the firsttime ensure that it is correctlyinstalled and connected. See"Installation and connection". Alsocheck that the drain filter is securelytightened to prevent the risk of waterleaks during use. The washer-dryer has a sensor whichmeasures the amount of laundr...

Reminder to remove transport struts To avoid the risk of damage, thetransport struts must be removedbefore the washer-dryer is used forthe first time. See "Installation andconnection" for instructions on howto do this. i Remove transportstruts OK ^ After removing the transport struts (ifthis...

Energy and water consumption – Water consumption and energy usage are determined by the size ofthe load.To make the most out of yourmachine, load the maximum dry loadfor the programme you are using. – Use the Automatic and Express programmes for small loads. – When smaller amounts of laundry are was...

Brief instructions The headings numbered A , B , C , . . . show the operating sequence and canbe used as brief instructions. Separate washing A Sort the laundry ^ Empty all pockets. , Foreign objects (e.g. nails, coins, paper clips, etc.) can causedamage to garments andcomponents in the machine. ^ B...

B Switch the machine on The interior drum lighting will come on. C Select a programme ^ Select the programme you want. The programme selected will appear inthe display. Minimum iron Further programmes: When you turn the programme selectorto Further programmes , a list of these programmes will appear...

E Add detergent The load size indicator display will bereplaced with the detergent percentagedisplay. Detergent 75% A 40% Add slightly less than half theamount recommended . . . 50% Add half the amountrecommended . . . 60% Add slightly more than half theamount recommended . . . 75% Add three quarter...

Extra options You can use the Extra option buttons to augment the basic wash programmes. Pre-wash For laundry with large amounts of dirt(e.g. dust, sand). Soak For heavily soiled and stained itemswith protein stains (e.g. blood, fatsand oils, cocoa). A length of time of between 30 minutesand 6 hours...

Spinning The maximum final spin speeddepends on the programme chosen. Programme rpm Cottons 1600 Minimum iron 1200 Delicates 600 Silks 400 Woollens 1200 Express 1600 Automatic 1200 Dark garments 1200 Shirts 600 Denim 900 Sportswear 1200 Outerwear 800 Proofing 1000 Curtains 600 Separate rinse 1200 St...

Programme chart Cottons 30°C to 95°C 9876 max. 5.0 kg Fabric type Cottons, linens or cotton mix fabrics. Extra options Pre-wash or Soak, Short, Water plus Detergent Powder detergent, detergent for coloured fabrics, liquiddetergent, tablet detergent and liquid tab detergent. Minimum iron 30°C to 60°C...

Silks / cold to 30°C c max. 1.0 kg Fabric type Silks and other handwashable fabrics with no wool content, e.g.satin, lace and silk. Note Place socks, tights, bras etc. in a washing bag. Extra option Water plus Detergent Liquid detergent for delicates. Woollens / cold to 40°C ac max. 2.0 kg Fabric ty...

Programme sequence Main wash Rinses Spinning Water level Wash rhythm Water level Rinses Spinning Final spin Cottons d a ( 2-3 2) L L Minimum iron d a ( 2-3 3) L L Delicates e b e 3 – L Silks e d e 2 – L Woollens ( c ( 2 L L Express d a ( 2-3 3) L L Automatic ( a ( 2-3 3) L L Dark garments ( a ( 3 L ...

Garment care label symbols / Hand wash (If no temperatureis specified use the lowesttemperature or cold) h Do not wash apf Dry clean D Do not dry clean y Suitable for chlorinebleaching z Do not use chlorine bleach Tumble dry q At normal temperature r At low temperature s Do not tumble dry Ironing I ...

The right amount to dispense willdepend on the following: – The soiling level of the laundry Lightly soiledNo visible dirt or stains. Normally soiledVisibly dirty and/or just a few slightstains. Heavily soiledStains and soiling clearly visible. – The water hardness level. Check with your local water...

Separate drying The separate drying programmemust be used if the load in the washprogramme is greater than themaximum load permitted for drying,or if you only want to dry part of theload that was washed. ^ Before drying check the dryingsymbol on the care label. q Dry at normal temperature r Dry at a...

D Load the drum ^ Open the drum door. ^ Load the laundry loosely into the drum. Do not overload the drum. See the"Programme chart" in the "Drying"section for recommended loads foreach programme. Overloading cancause unnecessary wear and tear to thelaundry and give a disappointing dry...

Extra option Low temperature The temperature is reduced duringthe drying programme. For all delicate or minimum iron fabricswith the r symbol on the care label (e.g. acrylic garments). With the exception of the Express programme, the thermospin is notcarried out when the Low temperature extra option...

Programme chart Cottons max. 2.5 kg* Extra dry, Normal+, Normal**, Timed drying 1) Fabric type Single and multi-layered cotton fabrics such as towelling,jerseywear, underwear, flannelette bed linen. Note Do not use Extra dry for jersey fabrics as they have a tendency to shrink. Extra options Low tem...

Washing and drying in acontinuous sequence Where the amount of laundry to bewashed and dried in one programmedoes not exceed the maximumweight permitted for the dryingprogramme, washing and drying inone continuous sequence isrecommended. It is very important to read both the"Washing" and ...

D Load the drum ^ Open the drum door and load thelaundry loosely in the drum. Follow the load size indicator and donot overload. Do not use detergent dispensingaids, e.g. plastic dispenser balls, forwashing followed immediately by thedrying programme. Thesedispensers can melt during thedrying progra...

^ Open the drum door fully . , Warning, the metal cap located on the inside of the door glass isvery hot after drying. Do not touch it. Danger of burning! ^ Remove the laundry. ^ Check the folds in the door seal forany small articles, e.g. buttons whichmight be lodged there. Remove anyfluff from dry...

Cancelling a programme You can cancel a programme at anytime after it has started. ^ Press the Start/Stop button briefly or turn the programme selector to Stop . ... During washing: The suds will be pumped away and thewashing programme is cancelled. ... During drying: The garments will be cooled dow...

With delay start you can choose whenyou want the programme to end. Thestart of a programme can be delayedfrom 30 minutes up to a maximum of 24hours, allowing you to make use ofnight-time economy electricity rates, forexample. The current time of day needs tohave been set for delay start to workcorre...

, Disconnect the machine from the electricity supply by switching off atthe wall socket and withdrawing theplug before any cleaning andmaintenance work. Cleaning the machine , Do not use solvents, abrasive cleaners, glass cleaners orall-purpose cleaning agents.These might damage plasticsurfaces and ...

What to do, if . . . With the help of the following notes, minor faults in the performance of theappliance, some of which may result from incorrect operation, can be put rightwithout contacting the Service Department. , Repair work to electrical appliances should only be carried out by a suitably qu...

Fault messages in the display Message in the display Possible cause Remedy A q Drainfault – The water outlet isblocked orrestricted. – The drain hose hasbeen fixed too high. – Clean the drain filter andthe drain pump asdescribed in "Openingthe drum door in theevent of a blocked drainoutlet and/o...

Problems with the load size indicator Problem Possible cause Remedy The displayindicates a load of<25% or no loadsize is indicatedwhen the drum isfull. There waslaundry in thedrum when themachine wasswitched on.This hasdecalibrated thesensor from thezero setting. To recalibrate the sensor to the ...

General problems Problem Possible cause Remedy The machine shakesduring the spin cycle. The machine feet are notlevel. Level the machine (see"Installation andconnection"). The pump makesstrange noises. This is not a fault! These noises occur at the end of apump sequence as a normal part of t...

An unsatisfactory wash result Problem Possible cause Remedy Liquid detergentdoes not give therequired result. Liquid detergentsusually contain nobleaching agents. Theydo not remove fruit,coffee and tea stains. – Use a general purposedetergent containing ableaching agent. – Pour stain removers intoco...

An unsatisfactory drying result Problem Possible cause Remedy The laundry is stilldamp after a dryingcycle. The load was too smallfor the electronics toassess the residualmoisture correctly. In future dry small loads in atimed drying programme. The laundry has formeda ring in the drum duringthe spin...

The drum door cannot be opened by pressing the Door button Problem Remedy The machine is notconnected to theelectricity supply and / oris not switched on. Insert the plug in the socket and switch on and /or switch the machine on with the I-On/0-Off button. The electronic programmelocking has beenact...

Once the flow of water ceases: ^ Remove the drain filter completely. ^ Clean it thoroughly. ^ Remove any foreign objects (e.g.buttons, coins, etc.) and fluff from thefilter housing. Turn the impeller byhand to check that it rotates freely. ^ Put the drain filter back in place andsecure. , Make sure ...

In the event of any faults which youcannot remedy yourself, pleasecontact: – your Miele dealer, or – the Miele Service Department (see back cover for contact details). When contacting the ServiceDepartment, please quote the modeland serial number of your appliance,both of which are shown on the data...

Front view a Inlet hose b Electricity supply cable c - f Flexible drain hose (with detachable swivel elbow) g Control panel h Detergent dispenser drawer i Drum door j Access to drain filter, drain pumpand emergency release k Handle recesses for moving themachine l Four height adjustable feet Install...

Rear view a Protruding lid for holding whenmoving the machine b Electricity supply cable c Transit bar covers d Inlet hose e Drain hose Installation and connection 61

Installation surface A concrete floor is the most suitableinstallation surface, being far lessprone to vibration during the spin cyclethan wooden floorboards or a carpetedsurface. Please note the following points: ^ The machine must be level andsecurely positioned. ^ To avoid vibrations during spinn...

^ Fit the covers on to the two holes.Then plug the holes as shown withthe caps. , The machine must not be moved without the transit fittings in place.Store them in a safe place for futureuse. They must be re-fitted if themachine is to be moved again (e.g.when moving house). Re-fitting the transit ba...

The Miele water protectionsystem The Miele water protection systemprotects the machine from waterdamage. The system consists of three maincomponents: 1) the inlet hose 2) the electronic unit and the machine housing 3) the drain hose 1) Inlet hose The inlet hose can withstandpressure of more than 7,0...

Connection to the water supply The machine should be connected to amains water supply in accordance withlocal and national safety regulations.The German authorities do not require itto have a non-return valve as themachine has been designed to complywith DIN regulations. The machine is designed to o...

Connection to the drainagesystem The machine drains via a drain pumpwith a delivery head of 1 metre*. Thedrain hose must not be kinked as thisrestricts drainage. The swivel elbow atthe end of the hose can be turned ineither direction, or can be detached ifrequired, with a sharp twist and pull. If re...

Load Consumption data Energy Water Duration in kWh in litres Short Normal Washing Cottons 95°C 5.0 kg 1.70 42 1 h 53 min 2 h 08 min 60°C 1) 5.0 kg 0.85 42 1 h 29 min 1 h 58 min 40°C 1) 5.0 kg 0.49 42 1 h 29 min 1 h 58 min Minimum iron 40°C 1) 2.5 kg 0.44 49 1 h 05 min 1 h 20 min Delicates 30°C 1.0 k...

Height 85.0 cm Width 59.5 cm Depth 58.0 cm Depth with door open 97.5 cm Weight 101 kg Maximum floor load 1600 Newton (approx. 160 kg) Capacity - Washing Capacity - Drying 5.0 kg dry laundry 2.5 kg dry laundry Voltage see data plate Connected load see data plate Fuse rating see plug Consumption data ...

To open the Settings menu A Switch on the machine. The mainmenu will appear. 15:03 Select programme B After a few seconds an additionalline will appear in the display. 15:03 Select programme Settings F ... C Confirm your selection by pressingthe OK button. D This will take you into the Settings menu...

Time of day Y You first have to decide whether youwant the time to show in the display.Then you have to select either a 24hour or 12 hour clock. Then set the current time of day. To select a 24 hour or 12 hour clock ^ Use the – and + buttons to select the clock option setting you want andconfirm you...

Gentle action U Activating gentle action reduces thedrum action and is suitable forwashing slightly soiled items moregently. It should be activated forgarments with a single bar under thecare label and for articles which feeltoo hard after they have been dried. Gentle action can be activated for the...

Distribution controller The maximum final spin speed islimited to prevent the laundry stickingto the drum. (This setting is onlyavailable when washing and dryingin a continuous sequence). There are 4 different options: 1200 rpm (factory default setting) 1100 rpm 1000 rpm 900 rpm. A tick will appear ...

Lock X The system lock prevents yourmachine being used without yourknowledge. When the system lock has beenactivated, you have to enter a codeafter switching the machine on.Otherwise the machine cannot beoperated. To activate the lock C Back A X Activate ^ Select Activate and confirm your selection....

Temperature S You can choose for the temperatureto be displayed as °C/Celsius or °F/Fahrenheit . A tick will appear beside the option toshow that it has been set. ^ Select the option you want andconfirm your selection. Buzzer O When the buzzer function has beenactivated, an audible tone sounds atthe...

Standby Q To save energy, the display goes outafter 10 minutes and the indicatorlight for the Start/Stop button will start flashing slowly. There are two options: On Standby is activated: – if a programme is not selected after the machine has been switched on. – after a programme has started. – at t...