Miele KM 7730 FR - User Manual

IMPORTANT SAFETY INSTRUCTIONS 6 Safety with children  Do not leave children unattended: Children should not be alone or unsupervised in the area where the appliance is installed. Do not al-low them to sit or stand on the appliance.  Be sure to supervise any children in the vicinity of the cooktop,...

IMPORTANT SAFETY INSTRUCTIONS 7 Technical safety  Proper installation: Make sure that your appliance has been in- stalled correctly and that it has been grounded by a qualified techni-cian.  Maintenance by the user: Never repair or replace any part of the appliance unless the instructions specific...

IMPORTANT SAFETY INSTRUCTIONS 9  The appliance must be completely disconnected from the electric- ity supply during installation, maintenance and repair work. Ensurethat power is not supplied to the appliance until after it has been in-stalled or until any maintenance or repair work has been carrie...

IMPORTANT SAFETY INSTRUCTIONS 10 Correct use  The cooktop gets hot when in use and remains hot for a while af- ter being turned off. There is a potential hazard until the residual heatindicator goes out.  Never leave the appliance unattended at high heat settings –  Boilover causes smoking and gre...

IMPORTANT SAFETY INSTRUCTIONS 14 Cleaning and maintenance  Do not use a steam cleaner to clean the cooktop. The steam may reach electrical components and cause a short cir-cuit.

Sustainability and environmental protection 15 Energy-saving tips - Cook in covered pots and pans if possible. This prevents heat escapingunnecessarily. - Cook with as little water as possible. - Once food has come to a boil or the pan is hot for frying, reduce the heatto a lower power level. - Use ...

Overview 16 Cooktop KM 7720 FR a Cooking zone with TwinBooster b Cooking zone with TwinBooster c Cooking zone with TwinBooster d Controls and indicators

Overview 19 Controls and display b a c d e h k g i f j a Stop & Go sensor controlFor stopping/starting a cooking process in progress b Cooktop On/Off sensor control c Wipe protection sensor controlFor locking the sensor controls d Keeping warm sensor controlFor activating/deactivating the Keepin...

Overview 20 Cooking zone data KM 7720 FR Cooking zone Ø  in inches (cm) 1 Max. rating in watts for 208 V 2 Linked cooking zone 3  7"–11" (18–28 cm) NormalTwinBooster, level 1TwinBooster, level 2 2,4002,7503,350 -  5 1/2"–7 1/2" (14–19 cm) NormalTwinBooster, level 1TwinBooster, leve...

Overview 24 KM 7740 FR Cooking zone Ø  in inches (cm) 1 Rating in watts for 208 V 2 Linked cooking zone 3  4"–6 1/2" (10–16 cm) NormalTwinBooster, level 1TwinBooster, level 2 1,3001,5502,000   6 1/2"–9"16–23 cm (16–23 cm) NormalTwinBooster, level 1TwinBooster, level 2 2,1002,7503,...

Overview 26 Power management system Total power The cooktop has a maximum total per-mitted power consumption which can-not be exceeded for safety reasons. The higher the total permitted powerconsumption of the cooktop, the morepower levels/functions can be used onall cooking zones at the same time. ...

Overview 27 Operation Cooktop when switched off When the cooktop is switched off, youcan only see the printed symbols for thesensor controls and the numerical dis-play. More sensor controls light upwhen the cooktop is switched on. Operation a Sensor controls and indicators This glass-ceramic cooktop...

Overview 28 Networking Your cooktop is equipped with an inte-grated WiFi module. The cooktop canbe connected to your home WiFi net-work or simply to your Miele ventilationhood. Miele@home After installing the Miele app on a mo-bile device, you can do the following: - call up information on the opera...

Overview 29 Functions Con@ctivity 3.0 Con@ctivity 3.0 is the direct communi-cation system between your cooktopand a Miele ventilation hood. Communi-cation is achieved by means of net-working. Con@ctivity 3.0 enables theventilation hood to operate automati-cally depending on the operating statusof yo...

Overview 30 Safety lock The safety lock is activated while thecooktop is switched on. When thesafety lock is activated, the cooktopcan only be operated under certainconditions. Keeping warm This function enables food to be keptwarm after it has finished cooking. The maximum duration for keeping food...

Overview 31 Safety shut-off Sensor controls are covered Your cooktop will turn off automaticallyif one or several of the sensor controlsremain covered for longer than 10 sec-onds; for example, by finger contact,food boiling over, or an object.   flashes briefly above the   sensor control and a ton...

Overview 32 Overheating protection In order to prevent the cooktop frombeing damaged by excessive tempera-tures, the overheating protection mech-anism intervenes in one of the followingways: Overheating protection measures - If the Booster function is switched on, it will stop. - The set power level...

Commissioning 33 Unpacking the cooktop  Please stick the extra data plate forthe appliance supplied with this doc-umentation in the space provided inthe “Customer Service” section ofthis manual.  Remove any protective foil and stick-ers. Cleaning the cooktop for thefirst time  Before using it for...

Commissioning 34 Miele@home Installing the Miele app The ability to use the Miele app de-pends on the availability of theMiele@home service in your country.For information about availability,please visit www.miele.com. The Miele app is available free ofcharge from the Apple App Store ® or from the G...

Commissioning 35 Connecting via the Miele app - A home WiFi network is available. - The signal of your WiFi network is sufficiently strong in the placewhere your cooktop is installed. - There is no direct WiFi connection between the cooktop and a Mieleventilation hood (Con@ctivity 3.0). - The Miele ...

Commissioning 36 Connecting via WPS - A home WiFi network is available. - The signal of your WiFi network is sufficiently strong in the placewhere your cooktop is installed. - There is no direct WiFi connection between the cooktop and a Mieleventilation hood (Con@ctivity 3.0). - You must have a WPS ...

Commissioning 37 Canceling the process  Touch any sensor control. Resetting settings Reset the settings if you are disposingof your cooktop, selling it, or putting aused cooktop into operation. This is theonly way to ensure that all personaldata has been removed and the previ-ous owner will no long...

Commissioning 38 Establishing a direct connec-tion with the ventilation hood The cooktop requires max. 2 W in net-worked standby. Availability of the Wi-Fi connection The Wi-Fi connection shares a fre-quency range with other appliances (in-cluding microwave ovens and remotecontrol toys). This can ca...

Operation 40 Safety notes for operation  Fire hazard due to overheated food. Unattended food can overheat and ignite. Do not leave the cooktop unattended while it is being used.  Risk of burning or scalding due to hot cooking zones. The cooking zones will be hot after use. Do not touch the cooking...

Operation 41 Switching the cooktop on  Touch the   sensor control. Additional sensor controls will light up. If no further entry is made, the cook-top will turn itself off after a few sec-onds for safety reasons. Switching off a cooking zone/the cooktop Switching off the cooktop  To switch off th...

Operation 42 Booster Activating the Booster function When the Booster function is activated,the settings for the linked cooking zonemay be changed (see “Overview –Power management system”). The Booster function can be used on amaximum of 2 cooking zones at thesame time. The Booster function is activ...

Operation 43 Auto heat-up The heat-up time depends on whichcontinued cooking level has been cho-sen: Continued cook- ing level* Heat-up time [min:sec] 1 approx. 00:15 1. approx. 00:15 2 approx. 00:15 2. approx. 00:15 3 approx. 00:25 3. approx. 00:25 4 approx. 00:50 4. approx. 00:50 5 approx. 2:00 5....

Operation 44 Timer Setting timer durations A duration of between 1 minute ( : ) and 9 hours 59 minutes ( : ) can be set. Durations of up to 59 minutes areshown in minutes (00:59) and durationsof more than 60 minutes are shown inhours and minutes. Durations are entered: - using the left or fron...

Operation 46 Using both timer functions at thesame time If you use both functions simultane-ously, the shortest time is always dis-played. The   sensor control (kitchen timer) or the indicator light of the cook-ing zone with the shortest switch-offtime pulsates.  If you want to show the times left...

Operation 47 System lock Activating the system lock All sensor controls are locked. A setkitchen timer will continue to countdown.  Touch the   sensor control for 6 seconds. The seconds can be seen countingdown in the timer display. When thistime has elapsed,   will appear in the timer display....

Operation 48 Keeping warm Activating/deactivating the Keepingwarm function  Touch the   sensor control for the cooking zone you wish to use. Keeping warm temperatures for vari-ous applications A keeping warm temperature of 185°F(85°C) is set as standard. You canchange the keeping warm temperature(...

Operation 49 Cooktop data Displaying the model identifier/serialnumber There must not be any cookware onthe cooktop.  Switch the cooktop on.  Press the 0 sensor control on any nu-merical display.  Press the 0 and 4 sensor controls onthe numerical display at the sametime for 6 seconds. Numbers wil...

Setting ranges 50 The cooktop is programmed with 9 power levels at the factory. If you wish to fine-tune a setting, you can extend the power level range to 17 power levels (see “Cus-tomizing settings”). Setting range Extended set- ting (17 power lev- els) Melting butter, chocolate, etc.Dissolving ge...

Good to know 51 How induction cooktops work An induction coil is located under eachcooking zone. The coil creates a mag-netic field that reacts directly with thebase of the pan and heats it up. Thecooking zone itself is heated up indi-rectly by the heat given off by the pan. An induction cooking zon...

Good to know 52 Cookware Suitable cookware - stainless steel with a magnetic base - enameled steel - cast iron The composition of the pan base canaffect the evenness of the cooking re-sults (e.g., when making pancakes). Thebase of the pan must be able to distrib-ute the heat evenly. Cookware with ab...

Good to know 53 Cookware tips - Position the cookware as centrally as possible on the relevant cookingzone/cooking area. - To make optimum use of the cooking zones, choose cookware with a suit-able base diameter (see “Overview –Cooking zone data”). If the cookwareis too small it will not be recogniz...

Customizing settings 54 Accessing programming mode The   sensor control is located ap- prox. 1/2" (1 cm) (index finger width) tothe left of the   sensor control. The cooktop is switched off.  Touch and hold the  and   sensor controls until the   sensor control lights up and  appears in t...

Cleaning and care 58 Safety notes on cleaning and care  Danger of burning due to hot surfaces. All parts of the cooktop may be hot after use. Turn off the cooktop. Allow the cooktop to cool down before cleaning it. All surfaces could be discolored or damaged if unsuitable cleaningagents are used or...

Cleaning and care 59 When to clean  The entire cooktop should be cleanedafter each use. Removing light soiling  Clean the entire ceramic surface ofthe cooktop with a damp, soft clothand a solution of water and a littlewashing-up liquid. Please follow thecleaning-agent manufacturer’s in-structions....

Frequently asked questions 60 Many malfunctions and faults that can occur in daily operation can be easily reme-died. You can save time and money in many cases, as you do not need to contactMiele Customer Service. Information to help you rectify faults yourself can befound at www.miele.com/service. ...

Frequently asked questions 61 Problem Possible cause and solution  will flash alternately with  ,  , or  in the timer display. The fan is blocked or defective.  Make sure it has not been blocked by an object.  Remove the obstruction.  If this fault message continues to appear in thedi...

Frequently asked questions 62 Unexpected behavior Problem Possible cause and solution The  symbol lights up or flashes alternatelywith the set power levelor  in one of the cook- ing zone indicators. No cookware is present on the cooking zone.Unsuitable cookware is present on the cooking zone.The b...

Frequently asked questions 64 Unsatisfactory results Problem Possible cause and solution Auto Heat-up is turnedon, but the food doesnot start cooking. Large amounts of food are being heated.  Start cooking at the highest power level, then re-duce the power level manually. The pan is not conducting ...

Customer Service 65 Information to help you rectify faults yourself and about Miele spare parts can befound at www.miele.com/service. Contact in the event of a fault In the event of a fault which you cannot remedy yourself, please contact yourMiele dealer or Miele Customer Service. You can book a Mi...

Optional accessories 66 Miele offers a range of useful acces-sories, as well as cleaning and condi-tioning products for your appliance. These products can be easily orderedfrom the Miele webshop. Cookware Miele offers a wide range of cookware.These have all been optimized for Mieleappliances in term...

Installation *INSTALLATION* 67 Safety notes for installation  Risk of damage caused by incorrect installation. Incorrect installation can damage the cooktop. The cooktop must only be installed by a qualified specialist.  Risk of electric shock from voltage. Incorrect connection to the power supply...

Installation *INSTALLATION* 68  Damage caused by incorrect installation. Using sealant under the cooktop could result in damage to thecooktop and the countertop if the cooktop ever needs to be re-moved for servicing. Do not use sealant between the cooktop and the countertop.The sealing strip under ...

Installation *INSTALLATION* 70 Safety distances Safety distance above the cooktop She safety distance specified by themanufacturer of the ventilation hoodmust be maintained between the cook-top and the ventilation hood above it. When two or more appliances whichhave different safety distances are in...

Installation *INSTALLATION* 71 Safety distance behind and to theside of the cooktop The minimum safety distances shownbelow must be maintained between theappliance and a tall cabinet or wall: - between the back    of the counter- top cut-out and the rear edge of thecountertop:2" (50 mm) and - o...

Installation *INSTALLATION* 72 Minimum safety distance underneath the cooktop To ensure sufficient ventilation to the cooktop, a minimum safety distance must beleft between the underside of the cooktop and any oven, protective base, ordrawer. The minimum safety distancebetween the underside of the c...

Installation *INSTALLATION* 73 Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained be-tween the countertop cut-out and the covering. High temperatures can alter ordamage these materials. ' ( & ) l * a Wall frame b Dimension x = thi...

Installation *INSTALLATION* 74 Installation dimensions KM 7720 FR All dimensions are given in mm and inches. The superscript numbers after the cut-out di-mensions are the tolerances for the cut-out. a Front b Flexible metal hose with power cords,L = 4' (1,200 mm)

Installation *INSTALLATION* 77 Reinstalling the cooktop  Create the countertop cut-out. Re-member to maintain the minimumsafety distances (see “Installation –Safety distances”).  Seal any cut surfaces on wooden countertops with a special varnish, silicone rubber, or resin to prevent thewood from s...

Installation *INSTALLATION* 78 Electrical connection  Damage through improper work. Installation, repair, and maintenancework performed by by unqualifiedpersons can cause considerabledanger to users.Miele cannot be held liable for anydamage arising as a result of suchwork.Installation, repair and m...

Installation *INSTALLATION* 79 Connection  Ensure that the connection data onthe data plate (voltage, frequency,and fuse rating) match those of yourelectrical supply. The data plate is located underneaththe appliance. The appliance is approved and readyfor connection to a grounded connectorwith thr...

Installation *INSTALLATION* 80 Declaration of conformity Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Informa-tion Induction Cooktop Unique Identifier: Miele Model: KM7720; KM7730; KM7740 Responsible Party Miele, Inc.National Headquarters9 Independence WayPrinceton, NJ 08540Phone:...

9 Independence WayPrinceton, NJ 08540www.mieleusa.com U.S.A. Miele, Inc. National Headquarters Please have the model and serial numberof your appliance available whencontacting Customer Service. Canada ImporterMiele Limited Headquarters and Miele Centre Customer Support Phone: 888-99-MIELE (64353)[e...