Miele HG01 - Manual

Disposal of the packingmaterial The cardboard box and packagingprotect the appliance during shipping.These materials are biodegradable andrecyclable. Please recycle. Ensure that any plastic wrappings,bags etc. are disposed of safely andkept out of the reach of children.Danger of suffocation! Disposa...

Opening the door without apanel in place ^ Gently pull on the upper portion ofthe mounting bracket until the doorlatch releases (small arrow). Without the mounting bracket inplace: ^ Grip the T shaped opening with afinger and pull the door open. Opening the door 8

G 600 Series Dishwashers Full size models G 643 - G 663 Removing the leg extensions The black leg extensions can beremoved to reduce the machine heightto 32 1 / 4 " - 33" (819-838 mm) (see Inset). A = Black leg extension (removable) B = White leg (must be installed onmachine). ^ After removi...

G 800 Series Dishwashers Full size models G 843 - G 863 Machine heights of 35" - 37"(889-940 mm) cannot be obtainedusing the supplied legs.For this height range, or for heightsgreater than 35" (889 mm), extendedlegs (part# 02 702 601) arenecessary.Contact the Miele Technical ServiceDepar...

1. Install the steam deflector A stainless steel steam deflector issupplied to protect the countertop fromsteam and condesation when thedishwasher is opened. If the countertopis made of Corian®, granite, marble orother solid, waterproof material, thesteam deflector is not required. The steam deflect...

^ Center the steam deflector in the opening for the dishwasher and alignwith the lower front edge of thecountertop. Note: For rounded countertops it may benecessary to pull the steam deflectorcloser to the counter’s edge so theoptic reflector will be visible. ^ Secure the deflector in place usingthe...

Stone or marble countertops: The steam deflector is not required forcountertops made of solid, waterproofmaterial. But it is needed fordetermining the correct position of theoptic indicator reflector. ^ Remove the black plastic reflectorholder and the tape holding it inplace from the steam deflector...

2. Install the mountingbrackets To ensure stability this dishwashershould be securely attached to thecountertop with the two mountingbrackets included. ^ Insert the tab of each bracket into theguide holes on top. Stone or marble counterops: Do not install these mounting bracketsif the counter is mad...

4. Install the dishwasher underthe countertop The dishwasher must be installed sothat the water and electricity suppliescan be accessed through an adjacentcabinet. The supplies must not belocated behind the machine. , WARNING - Fire hazard Do not cover or crush the plug of anelectric appliance. Ensu...

6. Install the custom doorpanel A custom door panel must be installedon the dishwasher before it can besafely operated. A single large panel ora two piece panel separated at thedrawer line can be used. Panel size is determined in thefollowing manner: Panel Height = HTC - TKH HTC = Height to the unde...

The door panel is attached to thedishwasher using the mounting bracketthat comes secured to the front of theunit. To remove the bracket: ^ Open the door 2 - 4" (5 - 10 cm). ^ Loosen the bracket retaining screw(black arrow) located on each side ofthe machine door. ^ Pull the bracket up until the ...

Install the bracket on the rear of thecustom door panel ^ Make sure the dishwasher is level. ^ Measure the distance X between the round hole in the machine outer doorpanel (shown in inset) and the loweredge of the adjoining cabinet door. ^ Place the door panel on a flatsurface, good side face down, ...

^ Place the bracket on the door panelso the notches, a , cross the previously drawn centerline, and thebottom of the bracket lines up withthe horizontal X line. ^ Mark and drill pilot holes for thescrews using a 3 / 32 " (2.5 mm) drill bit. ^ Attach the bracket to the back of thepanel, using the...

8. Secure the dishwasher ^ Open the dishwasher door. If the steam deflector is installed, themounting bracket holes must alignwith the slots in the steam deflector. ^ Using flat head screws, secure thedishwasher to the countertop byscrewing through both the mountingbracket and the steam deflector. M...

9. Adjust the door springs ^ Open the dishwasher door halfway. If the door remains in this position whenreleased, the springs are adjustedcorrectly. If the door drops, the tension on thesprings needs to be increased. If it closes on its own, the tension on thesprings need to be decreased. ^ To adjus...

Venting the drainage system If the dishwasher drain hose isconnected to a floor drain or to a drain pipe that is less than 8" (20 cm)above the floor, the drain must be vented. Otherwise the water inside thedishwasher may siphon out during thewash program. To vent the drain: ^ Open the dishwasher...

Power outlet The power outlet for the appliance mustbe installed within a cabinet, on a walladjacent to the undercounter space inwhich the dishwasher is located. Anopening through the partition betweenthe compartments of 1 1 / 2 " (3 to 4 cm) can be made to allow the plug to passthrough. Permane...

13. Install the toekick For installations using a continuoustoekick or a cabinet matching toekick Before installing the toekick,measurements must be taken to ensurethat the toekick will not interfere with thecomplete opening of the dishwasher door. The door panel overhang ( P ), and toekick depth of...

^ Carefully open the dishwasher dooruntil it hits the toekick. ^ Using the front lower edge of thedoor panel as a guide, draw a lineacross the toekick. ^ Unscrew and remove the toekick. ^ If one of the cutting lines is close tothe line just drawn, score the front ofthe toekick, and snap off the exce...