Miele DA 3590 - Manual

Technical safety ~ Before installation, check the cooker hood for visible signs of damage.Under no circumstances should youuse a damaged appliance. It could bedangerous. ~ Before connecting the appliance to the mains supply, make sure that thevoltage and frequency details given onthe data plate corr...

~ Do not connect the appliance to the mains electricity supply by amulti-socket unit or an extension lead.These do not guarantee the requiredsafety of the appliance (e.g. danger ofoverheating). ~ For appliances with an external fan motor fitted (...EXT models) theconnection of the two units must bem...

In order to ensure safe operation, andto prevent gases given off by theheating appliances from being drawnback into the room when the cookerhood and the heater are in operationsimultaneously, an underpressure of0.04 mbar (4 pa) is the maximumpermissible in the room. Ventilation can be maintained by ...

~ All ducting, pipework and fittings must be of non-flammable material.These can be obtained from the MieleSpare Parts department or frombuilders' merchants. ~ The appliance must not be connected to a chimney or vent fluewhich is in use. Neither should it beconnected to ducting which ventilatesrooms...

The cooker hood works with . . . air extraction: The air is drawn in, cleaned by thegrease filters and directed outside. If the on-site ventilation system doesnot have a non-return flap , then the non-return flap supplied with theappliance must be fitted in the exhaustsocket of the motor unit. Havin...

Con | ctivity This cooker hood is communicationenabled. Communication module XKM 2000 DA a , available as an optional extra, enables the operation of the cookerhood to be automatically controlled bythe operating status of a Miele electrichob with onset controls. For communication to take place, theh...

To switch the fan on ^ Pull the deflector plate downwardsslightly and then towards you. The fan will come on at power level 2 . The On/Off symbol K and Fan setting 2 will light up. To select a power level ^ Press the – symbol to select a lower power level or the + symbol to select a higher power lev...

Run-on option 5 ¢ 15 It is advisable to run the fan for a fewminutes after cooking has finished toneutralise any lingering odours in theair, whether you are using air extractionor recirculation mode. The fan can be set to switch offautomatically after 5 or 15 minutes. ^ After cooking has finished, p...

, Before any cleaning or maintenance work is carried out,disconnect the cooker hood from themains supply. , Exercise caution when changing halogen lamps. They get very hotduring use and remain hot for sometime after being switched off. Thehot lamps are also susceptible todamage from damp cleaning. W...

Controls The controls may sufferdiscolouration or damage if soiling isleft on them for too long. Removesoiling straight away. Please observe the General notes oncleaning earlier in this section. Do not use stainless steel cleaningagents on the controls. Grease filters The re-usable metal grease filt...

Changing a halogen lamp ^ Before any cleaning or maintenancework, disconnect the cooker hoodfrom the mains supply. , Exercise caution when changing halogen lamps. They get very hotduring use and remain hot for sometime after being switched off. Letthem cool down before you changethem. ^ To access th...

In the event of a fault which you cannotcorrect yourself, or if the appliance isunder guarantee, please contact: – Your Miele Dealer / Chartered Agent or – The Miele Service Department (see back cover for address). When contacting your Dealer or Miele,please quote the model and serialnumber of your ...

, Before installation, it is important to read the information given on thefollowing pages as well as theWarning and Safety instructions atthe beginning of this booklet.This is particularly crucial whenusing the cooker hood at the sametime as a heating appliance thatrelies on oxygen from the sameroo...

^ Pull the grease filters out of the slotsin the front of the cooker hoodhousing. The spacer strip needs to be attachedto the back of the cooker hood housingbefore the cooker hood is installed inthe wall unit. The spacer strip can beattached to the upper a or lower edge b of the deflector plate. ^ C...

Adjusting the deflector plate (DA 3560, DA 3590) When retracted, the deflector plate isheld in place by magnets.The retaining force of the magnets canbe adjusted.The magnets should be adjusted sothat the deflector plate is held in placesecurely on the left and right hand sideand can be lowered sligh...

^ Secure the spacer strip to the bottomof the wall unit as well. ^ Insert the cover for the charcoal filterslots as shown and close it. It is heldin place by magnets. ^ Take the grease filters out andremove any protective foil. Replacethe grease filters. Exhaust connection ^ Insert the non-return fl...

^ Fit the conversion kit as described inthe installation instructions suppliedwith the kit. ^ Make sure that the slats in theexhaust grille point towards thecentre of the room and not towards awall or the ceiling. A non-return flap is not used inrecirculation mode. ^ Fit the charcoal filters (see &#...

Important: To avoid the danger oftoxic fumes, please observe theWarning and Safety instructions.This is especially crucial when usingthe cooker hood at the same time asanother heating appliance whichrelies on air from the same room.The cooker hood should be installedaccording to local and nationalbu...

– If the exhaust air is to be ducted into the open air, the installation of atelescopic wall vent or roof vent(available as an optional accessory)is recommended. – If the exhaust air is to be ducted into a vent flue, the ducting must bedirected in the flow direction of theflue. Important: If the exh...

Silencer (optional accessory) To achieve even further reductions innoise levels, a special silencer can befitted in the ducting system. ...with air extraction: The silencer not only reduces noisefrom the fan, but also sounds fromoutside (e.g. traffic noise).For this reason the silencer must bepositi...

All electrical work should beundertaken by a suitably qualifiedand competent person in strictaccordance with current nationaland local safety regulations(BS 7671 in the UK). Installation, repairs and other workby unqualified persons could bedangerous, for which themanufacturer cannot be held liable....

The Miele DSM 400 control module(optional accessory) can be used tocombine the cooker hood with othercomponents. It enables the following: Potential free connection This can be used to operate anotherappliance by pulling out the deflectorplate and using the On/Off button s of the cooker hood. The po...

Connected load* DA 3560. . . . . . . . . . . . . . . . . . 170 WDA 3590. . . . . . . . . . . . . . . . . . 190 W Fan motor* . . . . . . . . . . . . . . . . . 130 WHob lighting DA 3560 . . . . . . . . . . . . . . . . 2 x 20 WDA 3590 . . . . . . . . . . . . . . . . 3 x 20 W Voltage . . . . . . . . . ....