Miele da 3360 - Manual

Technical safety ~ Before installation, check the cooker hood for visible signs of damage.Under no circumstances should youuse a damaged appliance. It could bedangerous. ~ Before connecting the appliance to the mains supply, make sure that thevoltage and frequency details given onthe data plate corr...

~ Do not connect the appliance to the mains electricity supply by amulti-socket adapter or an extensionlead. These do not guarantee therequired safety of the appliance (e.g.danger of overheating). ~ This appliance must not be used in a non-stationary location (e.g. on aship). ~ In areas which may be...

In order to ensure safe operation, andto prevent gases given off by theheating appliances from being drawnback into the room when the cookerhood and the heater are in operationsimultaneously, an underpressure of0.04 mbar (4 pa) is the maximumpermissible in the room. Ventilation can be maintained by ...

Correct use ~ Do not use an open flame beneath the cooker hood. To avoid the dangerof fire, do not flambé or grill over anopen flame.When switched on, the cooker hoodcould draw flames into the filter. Fatparticles drawn into the cooker hoodpresent a fire hazard. ~ When using the cooker hood over a g...

The cooker hood works with . . . air extraction: The air is drawn in, cleaned by thegrease filter and then directed outside. If the on-site ventilation system doesnot have a non-return flap , then the non-return flap supplied with theappliance must be fitted in the exhaustsocket in the motor unit. H...

, Before any cleaning or maintenance work is carried out,disconnect the cooker hood from themains supply. , Exercise caution when changing halogen lamps. They get very hotduring use and remain hot for sometime after being switched off. Thehot lamps are also susceptible todamage from damp cleaning. W...

Controls The controls may sufferdiscolouration or damage if soiling isleft on them for too long. Removesoiling straight away. Observe the General notes on cleaningearlier in this section. Do not use stainless steel cleaningagent on the controls. Grease filter The re-usable metal grease filter in the...

Cleaning the grease filter by hand ^ Clean the filter with a soft nylon brushin a mild solution of hot water and alittle washing-up liquid.Do not use "neat" washing-up liquid. Do not use: – cleaning agents containing descaling agents, – powder cleaners, cream cleaners or abrasive all-purpose...

Changing a halogen lamp ^ Pull out the deflector plate, andremove the grease filter as describedearlier. ^ Switch off the fan and the lighting. , Exercise caution when changing halogen lamps. They get very hotduring use, and remain hot for sometime after being switched off. Do nottouch the surface d...

In the event of a fault which you cannotcorrect yourself, or if the appliance isunder guarantee, please contact: – Your Miele Dealer / Chartered Agent or – The Miele Service Department (see back cover for address). When contacting your Dealer or Miele,please quote the model and serialnumber of your ...

1) The front section of the wall housingunit must be fitted with a shelf to thedepth of the partition wall.If the appliance is fitted further back,e.g. to accomodate a front panel, thenthe shelf depth should becorrespondingly deeper. 2) The partition wall in the wall unit mustbe removable. 3) In ext...

Positioning the appliance inthe wall housing unit To position the appliance correctly,cut the spacer strip to required depthT, and then attach it to the back ofthe appliance. T = Depth of carcase K minus depth of appliance G ^ Example a shows the installation without a front panel fitted and withthe...

^ Lift the appliance up into the housingfrom below until it engages in thebrackets. Note for dismantling the cooker hood:Undoing the screws on the left andright inside the housing releases thespring mounts, allowing theappliance to be removed from theunit. ^ Push the cooker hood back againstthe spac...

^ Remove the protective film betweenthe deflector plate and the casing. ^ Secure the front of the appliance tothe floor of the housing unit frombelow using 4 screws. To avoid damaging the deflector platewhen it is pulled out, care should betaken to screw the fixing screws instraight, and to ensure t...

Aligning the deflector plate ^ The position of the deflector platecan be brought forward by up to35 mm using the adjusting screws oneither side of the deflector plate.Align the deflector plate to the front ofthe kitchen furniture units on eitherside. Fitting the grease filter ^ Remove the protective...

Vent ducting ^ If the on-site ventilation system doesnot have a non-return flap , then the non-return flap supplied with theappliance must be fitted in theexhaust socket in the motor unit. ^ When using C 150 mm ducting, secure the exhaust socket suppliedto the exhaust ducting with hoseclips. ^ If us...

Setting up for recirculationmode If site conditions are not suitable for thecooker hood to be used with airextraction, the appliance must be setup for recirculation. For this, conversion kit DUU 151(available from your Miele dealer or theMiele Spare Parts Department) isrequired. You will also need a...

Important: To avoid the danger oftoxic fumes, please observe theWarning and Safety instructions.This is especially crucial when usingthe cooker hood at the same time asanother heating appliance whichrelies on air from the same room.The cooker hood should be installedaccording to local and nationalbu...

Condensate trap (optional accessory) In addition to insulating the exhaustducting, we recommend that a suitablecondensate trap is also installed tocollect and evaporate any condensatewhich may occur. Condensate trapsare available for C 125 mm or C 150 mm ducting. When installing a condensate trap,en...

Silencer (optional accessory) To achieve even further reductions innoise levels, a special silencer can befitted in the ducting system. ...with air extraction: The silencer not only reduces noisefrom the fan, but also sounds fromoutside (e.g. traffic noise).For this reason the silencer must bepositi...

All electrical work should beundertaken by a suitably qualifiedand competent person in strictaccordance with current nationaland local safety regulations(BS 7671 in the UK). Installation, repairs and other workby unqualified persons could bedangerous, for which themanufacturer cannot be held liable....

Connected load . . . . . . . . . . . . . . 210 W Fan motor . . . . . . . . . . . . . . . . . 110 WHob lighting . . . . . . . . . . . . . . 2 x 50 W Voltage . . . . . . . . . . . . . . . . . . . . 230 V Frequency . . . . . . . . . . . . . . . . . ~ 50 Hz Fuse rating U.K. . . . . . . . . . . . . . . ....