Miele CS1028 - Manual

~ Before servicing, turn off the gas valve and disconnect the power supplyby either removing the fuse, unpluggingthe unit or manually “tripping” thecircuit breaker. ~ This equipment has not been designed for maritime use or for use inmobile installations such as aircraft orrecreational vehicles. How...

a Burner grate b Burner c Control knob Guide to the combiset 9

Burner d Burner cap e Burner head f Cover plate g Ignitor h Ignition safety control(Thermocouple) i Burner base Guide to the combiset 10

Cleaning the combiset Before using for the first time clean theappliance as follows: ^ Remove any protective foil. ^ Wash the removable parts of the gasburner in a mild solution of warmwater and liquid dish soap. ^ Dry and reassemble the parts in thecorrect order (see "Cleaning andcare"). ^ ...

Turning on and off / Regulating The control knob is used to turn on theburner and to regulate the strength ofthe flame. ß The gas supply is turned off * Ignition setting & Highest flame / Lowest flame The knob must only be turned left toturn the appliance on and right toturn it off. If the knob ...

Pan size – Set the combiset to a high flame when using a large diameter pan andlow flame when using a smalldiameter pan. – Generally, wide / shallow pans will heat faster and cook more evenlythan narrow / tall ones. – Using oversized pans may cause the flames to spread out and damagethe surrounding ...

Ignition Safety Control This gas combiset incorporates anIgnition Safety Control which stops thesupply of gas if the flame goes out. ^ To reignite the burner, turn thecontrol knob clockwise to “ ß ”, then turn on the burner as usual. This safety feature is not operated byelectricity, it will be acti...

Never use a steam cleaner to cleanthis combiset. Pressurized steamcould cause permanent damage tothe surface and to components forwhich the manufacturer cannotaccept responsibility. Do not use any sharp or pointedobjects which could damage theseal between the frame and thecountertop. Never use scour...

Burner Do not clean any parts of the burnerin a dishwasher. The burner can be dismantled andcleaned when cool. ^ Remove the burner parts and washthem in a solution of warm water andliquid dish soap. Dry themthoroughly. Make sure that the flameholes are clean and completely dry. ^ Wipe the burner bas...

, Repairs should only be carries out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairscould cause injury or appliance damage. The manufacturer cannot be heldresponsible for unauthorized work. The burner does not ignite after several attempts. ...

In the event of a fault which you cannoteasily fix yourself, please contact theMiele Technical Service Department atthe address on the back of this booklet. When contacting Technical Serviceplease quote the serial number andmodel of the appliance. Adhere rating label sticker suppliedwith the applian...

MieleCare (USA only) MieleCare , our Extended Service Contract program; gives you theassurance of knowing that yourappliance investment is covered by 5years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guaranteesrepairs by a Miele Authorized ServicePr...

Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidentsand appliance damageread these instructions before installation or use.

Installation The minimum distances given inthese Installation instructions are tocombustible surfaces, and must beobserved to ensure safe operation.Failure to do so increases the risk offire. The cabinetry and venting hoodshould be installed first to preventdamage to the combiset. ~ Gas appliances s...

Safety distances to the sidesof the appliance The appliance should only be installedas shown in the illustrations, whilemaintaining the required safetydistances shown. Do not install theappliance between two tall cabinets,this is a fire hazard. A distance of at least 2" (50 mm) mustbe kept betwe...

Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintainedbetween the countertop cut-out and the covering, since high temperatures candamage these materials. If the covering is made of a combustible material (such as wood), the distancebetwee...

Installation dimensions a Spring clips b Appliance front c Installation height d Power supply box with connection cable, L = 78 3/4" (2000 mm) e Gas fitting f Rating label Installation 26

Cut out ^ Make the countertop cut-out for oneor more appliances as applicable.Remember to maintain a minimum safety distance from the back wall , as well as from any tall unit or side wall to the right or left of the hob. See "IMPORTANT SAFETYINSTRUCTIONS". ^ Seal the cut surfaces with a sui...

Sample calculations for a countertop cut-out for three appliances A appliance width minus 5/16" (8 mm) B appliance width C appliance width minus 5/16" (8 mm) D Countertop cut-out 11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 33 3/8" (848 mm) 11" (280 mm) 15" (380 mm) 14...

Attach the spring clips andsupport bars Wood or solid surface countertops ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above,by laying them on the upper edge ofthe cut-out and then securing themwith the 1 / 8 " x 1" (3.5 x 25 mm) screws (supplie...

Granite countertop The screws are not needed forgranite countertops. ^ Position and attach the spring clips a and support bars b with strong, double-sided tape c . ^ Coat the edges of the spring clips a , ^ and the space e between the support bars b and the countertop with silicone (supplied). Insta...

Installing the appliance /appliances ^ Feed the power cord down throughthe cut-out. ^ Place the front edge of the applianceinto the cut-out. ^ With a hand on each side of theappliance press down evenly on theedges until it clicks into position.When doing so make sure that theappliance seal sits tigh...

This appliance must be groundedaccording to local or national codes. All electrical work should beperformed by a qualified electricianin accordance with local codes andwith the: - National Electrical CodeANSI / NFPA No. 70for the USA or- Canadian Electrical Code Part Ifor Canada(CSA Standard C 22.1)...

Installation and service must beperformed by a qualified installer,service agency or the gas supplier. In Massachusetts a licensedplumber/gas fitter is required. This appliance must be installedwith its own shut off valve and theincluded gas pressure regulator.Both the valve and the regulatormust be...

Gas pressure regulator A pressure regulator that is convertiblefrom natural to LP gas (Propane) or viceversa is included with the appliance.The included regulator correspondswith the gas type of the combiset. Verifybefore installing. The adjusted pressure is:natural gas - 4" w.c.LP gas - 10"...

Nominal ratings Maximum output Gas type BTU/hr kW Natural Gas (NG) 27,600 8.1 Liquid Gas(Propane) (LP) 22,200 6.5 Minimum output Gas type BTU/hr kW Natural Gas (NG) 5,700 1.67 Liquid Gas(Propane) (LP) 5,700 1.67 Gas connection 39

The combiset should have beenordered for connection to either naturalgas or LP gas (propane). If the combiset is not configured for theproper type of gas connection pleasecontact your Miele Dealer. If the appliance is to be connected to atype of gas other than it was originallyconfigured for, both t...

Disposal of packing materials The cardboard box and packingmaterials are biodegradable andrecyclable. Please recycle. Ensure that any plastic wrappings,bags, etc. are disposed of safely andkept out of the reach of children.Danger of suffocation! Disposal of an old appliance Old appliances contain ma...