Miele 9775890 - User Manual

IMPORTANT SAFETY INSTRUCTIONS 6 Children  As with any other appliance, children must be supervised.  Do not leave children unattended: Children should not be alone or unsupervised in the area where the oven is installed. Do not allow them to sit or stand on the appliance.  Children under eight ye...

IMPORTANT SAFETY INSTRUCTIONS 7 Technical safety  Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instruc‐ tions. Contact Miele’s Technical Service Departmen...

IMPORTANT SAFETY INSTRUCTIONS 10 Proper use  The cooktop gets hot when in use and remains hot for a while af‐ ter being turned off. There is a potential hazard until the residual heat indicator goes out.  When in use, the cooktop emits a significant amount of heat, which can cause objects in the v...

IMPORTANT SAFETY INSTRUCTIONS 14 Cleaning and care  Do not use a steam cleaner to clean the cooktop. The steam may reach electrical components and cause a short cir‐ cuit.  If the cooktop is built in over a self cleaning oven, the cooktop should not be used while the self cleaning process is being...

Overview 15 KM 6360 / KM 6365 a Cooking zone with TwinBooster b Cooking zone with Booster c PowerFlex cooking zone with TwinBooster d PowerFlex cooking zone with TwinBooster cd can be combined to form PowerFlex cooking zone e DirectSelection Plus controls

Overview 16 KM 6370 / KM 6375 a Cooking zone with Booster b PowerFlex cooking zone with TwinBooster c PowerFlex cooking zone with TwinBooster bc can be combined to form PowerFlex cooking zone d Cooking zone with Booster e Cooking zone with TwinBooster f DirectSelection Plus controls

Overview 17 KM 6377 a PowerFlex cooking zone with TwinBooster b PowerFlex cooking zone with TwinBooster ab can be combined to form PowerFlex cooking zone c Cooking zone with TwinBooster d PowerFlex cooking zone with TwinBooster e PowerFlex cooking zone with TwinBooster de can be combined to form Pow...

Overview 18 DirectSelection Plus controls 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 h f o 8 8 m e c l n p k i a b d g j h Sensor buttons a Turning the cooktop On/Off b Activating and deactivating the System lock/Safety lock c Switching the ti...

Overview 19 m System lock/Safety lock activated n For cooking zone selection, e.g., right rear cooking zone o TwinBooster activated  Level 1  Level 2 p Timer display  to  Time in minutes . to . Time in hours  System lock/Safety lock activated  Demo mode activated Cooking zone data KM 6...

Before using for the first time 22  Please adhere the extra data plate for the appliance supplied with this doc‐ umentation in the space provided in the "After sales service, data plate, warranty" section of this manual.  Remove any protective foil and stick‐ ers. Cleaning the cooktop for ...

Induction 23 How it works An induction coil is located under each cooking zone. When a zone is turned on, this coil creates a magnetic field that impacts directly on the base of the pan and heats it up. The cooking zone itself is heated up indirectly by the heat given off by the pan.An induction coo...

Induction 24 Noises When you use an induction cooking zone, the following noises may occur, depending on the type and shape of the cookware bottom:On the higher power settings, it might buzz. This will decrease or cease alto‐ gether when the power setting is re‐ duced.Cookware with bottoms made of d...

Induction 25 Cookware Suitable cookware is made of: – Stainless steel with a magnetizable bottom – Enamel-coated steel– Cast iron Unsuitable cookware is made of: – Stainless steel with a non-magnetiza‐ ble bottom – Aluminum or copper– Glass, ceramics, earthenware, stone‐ ware To test whether a pot o...

Energy saving tips 26 – Use a lid whenever possible to mini‐ mize heat loss. – For small quantities, select a small pan. A small pan on a small burner uses less energy than a large, only partially filled pan on a large burner. – Cook with as little water as possible.– Once food has come to the boil ...

Power setting ranges 27 The cooktop is programmed with 9 power levels at the factory. If you wish to fine- tune a setting, you can extend the power setting range to 17 power levels (see "Programming"). Setting ranges Default (9 power levels) Extended (17 power levels) Keep warm level h h Mel...

Operation 28 Basic operation The glass ceramic cooking zone is equipped with electronic sensor but‐ tons that react to finger contact. During activation, the On/Off  sensor button must be pressed somewhat longer than the other buttons for safety reasons. Each reaction of the buttons is ac‐ knowledg...

Operation 29  Fire hazard! Do not leave the cooktop unattended during operation! Please note that the heat-up time for induction cooktops is shorter than for conventional cooktops. Turning on  To turn on the cooktop, briefly touch the  sensor button. All of the sensor buttons will light up. If no...

Operation 30 Setting the power level - ex‐ panded setting range  Tap the control scale between the sensor buttons. The sensor buttons in front of and be‐ hind the medium level light up brighter than the other buttons.Example: If you have selected power setting 7., the numbers 7 and 8 will be bright...

Operation 32 TwinBooster / Booster The cooking zones are equipped with a booster or TwinBooster (see "Overview – Cooking zone"). You can use the booster for a maximum of two cooking zones at the same time.When activated, the power is boosted for a maximum of 15 minutes so that large quantiti...

Operation 33 During the booster time, the  sensor button and all of the sensor buttons on the control scale are at brightness level 2. Activating the booster  Tap the  sensor button on the con‐ trol scale for the desired cooking zone.  Select a power level if required.  Tap the  sensor button....

Operation 34 Keep warm function The keep warm function is for keeping food warm that has just been cooked, i.e., food that is still hot. It is not for reheating cold food. If the keep warm function has been ac‐ tivated, the cooking zone will turn off automatically after a maximum of 2 hours.– Only u...

Timer 35 The cooktop has to be turned on if you wish to use the timer. You can set a time between 1 minute (  ) and 9 hours ( . ). The timer can be used for two different functions: – For setting the timer– For turning off a cooking zone auto‐ matically. A time up to 99 minutes is set and dis‐ p...

Timer 36 Setting the hours To set full hours, tap the respective sensor button on the control scale. To set the half hours, tap the space be‐ tween 2 sensor buttons on the control scale.Example: You want to set a time of 2 hours and 30 minutes.  Turn the cooktop on.  Tap the  sensor button. The ...

Timer 37 Turning a cooking zone off au‐ tomatically You can set a time after which the cooking zone will turn off automatically. This function can be used on all zones at the same time. If the programmed time is longer than the maximum time allowed, the safety shut-off function will turn off the coo...

Timer 38 Using both timer functions at the same time The timer and automatic turn-off func‐ tions can be used at the same time.If you have programmed in one or more turn-off times, and would like to use the timer as well:  Tap the  sensor button until the in‐ dicator lights of the programmed cooki...

Additional functions 39 Stop & Go function When activated, the Stop & Go reduces the power of all cooking zones in use to power level 1. The power levels of the zones and set‐ ting of the timer cannot be changed and the cooktop can only be turned off. A set timer and booster time continue to...

Safety features 40 System lock / Safety lock The system lock and safety lock are deactivated if there is a power out‐ age. Three-finger control is the default set‐ ting. You can change the default to one-finger control (see "Program‐ ming"). Your cooktop is equipped with a safety lock to pre...

Safety features 41 Safety shut-off Safety shut-off with an overlong cooking time The safety shut-off is triggered auto‐ matically if a cooking zone is heated for an unusually long period of time. This time depends on the power level se‐ lected. If it has been exceeded, the cooking zone turns off and...

Safety features 42 Overheat protection All the induction coils and the cooling elements for the electronics are equip‐ ped with an overheating protection mechanism. To prevent the induction coils and cooling elements from over‐ heating, the overheating protection mechanism works on the affected cook...

Cleaning and care 43  Burn hazard! The burners must be turned off and allowed to cool completely.  Risk of injury! The steam from a steam cleaner could reach electrical components and cause a short circuit.Do not use a steam cleaner to clean the cooktop. All cooktop surfaces can become discolored ...

Cleaning and care 44 Do not clean the area between the glass-ceramic surface and the frame or the frame and the counter with sharp objects.This could cause damage to the seals. When cleaning with dishwashing liq‐ uid, not all contaminants and resi‐ dues are removed.An invisible film forms, which cau...

Programming 45 You can adapt the programming of the cooktop to your personal needs. Sever‐ al settings can be changed in succes‐ sion.After the programming function is start‐ ed,  (program) and  (status) will ap‐ pear in the timer display. With cooktops that have 3 cooking zones, an addition‐ al d...

Frequently asked questions 48 The following guide is intended to help you resolve problems that occur during normal operation of the appliance. If you are unable to identify or remedy the cause of the problem on your own, please contact Miele Service (see back cover for details).  Risk of injury! I...

Frequently asked questions 51 Problem Possible cause and solution  Alternating with a number flashes in the timer dis‐ play.  The overheat protection was triggered.  See "Overheat protection."  or  The fan is blocked or defective.  Make sure it has not been blocked by somethi...

Con @ ctivity 52 Your cooktop is communication ena‐ bled and can communicate with the ventilation hood using the wireless USB stick included with selected ventilation hoods (Con @ ctivity). The cooktop sends information on its operating sta‐ tus to the ventilation hood. The opera‐ tion of the ventil...

IMPORTANT SAFETY INSTRUCTIONS - INSTALLATION 53  Installation and connection of the cooktop to the electrical power supply may only be performed by a qualified electrician. Install the upper cabinets and venti‐ lation hood before installing the cooktop to avoid damaging it.  Reaching over a hot co...

Safety clearances 54 Safety clearance above the cooktop For a ventilation hood above the cook‐ top, always use the clearance specified by the hood manufacturer. If there are no specifications from the hood manu‐ facturer or if flammable materials (e.g. a utensil rail) are installed above the cooktop...

Safety clearances 55 Safety clearances to the sides and back of the cooktop In installing a cooktop there may be an optionally high cabinet or room wall against the rear side and one of the sides (right or left) (see illustrations).  minimum distance between the back of the counter cut-out and the ...

Safety clearances 56 Minimum clearance under‐ neath the cooktop To ensure proper ventilation of the cooktop, a minimum clearance is re‐ quired between the appliance and an oven, protective base, or drawer.The minimum clearance from the bot‐ tom of the cooktop to – the top of the oven must be ⁹/₁₆...

Safety clearances 57 Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained be‐ tween the countertop cut-out and the covering, since high temperatures can dam‐ age these materials.If the covering is made of a combustible material (such as...

Ventilation 58 a Front b Ventilation cut-out in the rear wall of the base unit (Slight) ventilation also takes place when the base unit is directly against the wall. c Protective base The installation of a protective base beneath the cooktop is not required, but permitted. If a protective base is in...

Framed cooktops 59 Instructions for installation Seal between cooktop and counter In case a disassembly is required, the appliance must not be perma‐ nently sealed into the countertop when installed. The sealing strip un‐ der the edge of the appliance pro‐ vides a sufficient seal for the coun‐ terto...

Framed cooktops 60 Installation dimensions KM 6360 a Front b Installation height c Flexible metal hose with power cord L = 3' 11¹/₄" (1200 mm) d Data plate

Framed cooktops 63 Installation Preparing the counter  Create the counter cut-out as shown in the cooktop diagram and in the de‐ tailed drawing. Remember to main‐ tain a minimum safety distance (see "Safety clearances").  Seal any wooden counter surfaces with a special varnish, silicone ru...

Flush-mounted (frameless) cooktops 67 Installation Granite and marble counters a Countertop b Cooktop c Gap As the ceramic glass slab and the counter cut-out have a certain dimen‐ sional tolerance, the width of the gap  (min. ¹/₁₆" [2 mm]) can vary. KM 6365 d Stepped cut-out KM 6375 d Stepped c...

Electrical connection 69  ATTENTION: Before installation or servicing, dis‐ connect the power supply by either removing the fuse, shutting off the main power or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accor...

Electrical connection 70 Connection  Ensure that the connection data on the data plate (voltage, frequency, and fuse rating) match those of your electrical supply. The data plate is located underneath the cooktop. The cooktop is approved and ready for connection to a grounded connector with three c...

Caring for the environment 71 Disposal of the packing mate‐ rial The cardboard box and packing materi‐ als protect the appliance during ship‐ ping. They have been designed to be biodegradable and recyclable.Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reac...

Technical service, data plate, warranty 72 After sales service In the event of a fault which you cannot easily correct yourself, please contact: – your Miele dealer, or– the Miele Technical Service Department. See back cover for contact details. Please quote the model and serial number of your appli...

MieleCare 73 This service is available in USA only. MieleCare , our Extended Service Con‐ tract program, gives you the assurance of knowing that your appliance invest‐ ment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees ...

9 Independence WayPrinceton, NJ 08540Phone: Fax:www.mieleusa.com U.S.A. Miele, Inc. National Headquarters Please have the model and serial numberof your appliance available beforecontacting Technical Service. Canada ImporterMiele Limited Headquarters and Miele Centre 800-843-7231609-419-9898609-419-...