Miele 9026700 - User Manual

~ Before servicing, turn off the gas valve and disconnect the power supplyby either removing the fuse, unpluggingthe unit or manually"tripping" the circuitbreaker. ~ This equipment has not been designed for maritime use or for use inmobile installations such as aircraft orrecreational vehicl...

a Fast burner b Normal burner c Burner grate d Burner indicators e Display Indicators l On/Off indicator m "Residual Heat" Indicator Control knobs: f Rear burner g Front burner Guide to the combiset 9

Burner n Burner cap o Burner head p Ignition safety control(Thermocouple) q Ignitor r Burner base Guide to the combiset 10

Cleaning the combiset Before using for the first time clean theappliance as follows: ^ Remove any protective foil. ^ Wash the removable parts of the gasburner in a mild solution of warmwater and liquid dish soap. ^ Dry and reassemble the parts in thecorrect order (see "Cleaning andcare"). ^ ...

Fast-Ignition-System The gas combisets are equipped with aFast-Ignition-System whichincorporates the following features: – The control knob does not need to be pressed until the flame lights. – If the flame goes out because of a draft, for example, the burner isautomatically re-ignited.If re-ignitio...

Burner Min. bottom diameter of cookware Normal burner 4 3 / 4 " (12 cm) Fast burner 5 1 / 2 " (14 cm) Max. top diamter of cookware Normal burner 8 11 / 16 " (22 cm) Fast burner 9 7 / 16 " (24 cm) – Follow the dimensions given in the table. If the bottom diameter is toosmall the cookw...

Ignition safety control This appliance is equipped with anIgnition Safety Control. This control cutsthe gas supply if the flame goes outand reignition is unsuccessful. ^ To reignite the burner, turn thecontrol knob to" ß ", then switch the burner on as usual. Safety cut-off If a zone has bee...

Never use a steam cleaner to cleanthis combiset. Pressurized steamcould cause permanent damage tothe surface and to components. Do not use any sharp or pointedobjects which could damage theseal between the frame and thecountertop. Never use scouring agents, pads,abrasive cleaning agents, or strongcl...

Burners The burner can be dismantled andcleaned when cool. ^ Remove the burner parts and washthem in a solution of warm water andliquid dish soap. Dry themthoroughly. Make sure that the flameholes are clean and completely dry. ^ Wipe the burner base clean with adamp cloth and then dry. ^ Gently wipe...

, Repairs should only be carries out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairscould cause injury or appliance damage. The burner does not ignite when the combiset is being used for the firsttime or after an extended period of not being...

In the event of a fault which you cannoteasily fix yourself, please contact theMiele Technical Service Department atthe address on the back of this booklet. When contacting Technical Serviceplease quote the serial number andmodel of the appliance. Technical Service 22

MieleCare (USA only) MieleCare , our Extended Service Contract program; gives you theassurance of knowing that yourappliance investment is covered by 5years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guaranteesrepairs by a Miele Authorized ServicePr...

Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the mostcurrent product specification, technical & warranty information. To prevent accidentsand appliance damageread these instructions befo...

Installation The minimum distances given inthese Installation instructions are tocombustible surfaces, and must beobserved to ensure safe operation.Failure to do so increases the risk offire. The cabinetry and venting hoodshould be installed first to preventdamage to the combiset. ~ Gas appliances s...

Safety distances to the sidesof the appliance The appliance should only be installedas shown in the illustrations, whilemaintaining the required safetydistances shown. Do not install theappliance between two tall cabinets,this is a fire hazard. A distance of at least 2" (50 mm) mustbe kept betwe...

Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintainedbetween the countertop cut-out and the covering, since high temperatures candamage these materials. If the covering is made of a combustible material (such as wood), the distancebetwee...

Installation dimensions a Spring clips b Appliance front c Installation height d Power supply box with connection cable, L = 47 1/4" (1200 mm) e Gas fitting f Rating label Installation 30

Cut out ^ Make the countertop cut-out for thedesired number of appliances.Remember to maintain a minimum safety distance from the back wall , as well as from any tall unit or side wall to the left or right of the combiset.See also the "IMPORTANT SAFETYINSTRUCTIONS". ^ Seal the cut surfaces w...

Sample calculations for a countertop cut-out for three appliances A appliance width minus 5/16" (8 mm) B appliance width C appliance width minus 5/16" (8 mm) D Countertop cut-out 11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 33 3/8" (848 mm) 11" (280 mm) 15" (380 mm) 14...

Attach the spring clips andsupport bars Wood or solid surface countertops ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above,by laying them on the upper edge ofthe cut-out and then securing themwith the 1 / 8 " x 1" (3.5 x 25 mm) screws (supplie...

Granite countertop The screws are not needed forgranite countertops. ^ Position and attach the spring clips a and support bars b with strong, double-sided tape c . ^ Coat the side and lower edges of thespring clips between a and b with silicone. ^ Fill the space e between the support bars b and the ...

Installing the appliance /appliances ^ Feed the power cord down throughthe cut-out. ^ Place the front edge of the applianceinto the cut-out. ^ With a hand on each side of theappliance press down evenly on theedges until it clicks into position.When doing so make sure that theappliance seal sits tigh...

This appliance must be groundedaccording to local or national codes. All electrical work should beperformed by a qualified electricianin accordance with local codes andwith the: - National Electrical CodeANSI / NFPA No. 70for the USA or- Canadian Electrical Code Part Ifor Canada(CSA Standard C 22.1)...

Installation and service must beperformed by a qualified installer,service agency or the gas supplier. In Massachusetts a licensedplumber/gas fitter is required. This appliance must be installedwith its own shut off valve and theincluded gas pressure regulator.Both the valve and the regulatormust be...

Gas pressure regulator A pressure regulator that is convertiblefrom natural to LP gas (Propane) or viceversa is included with the appliance.The included regulator correspondswith the gas type of the combiset. Verifybefore installing. The adjusted pressure is:natural gas - 4" w.c.LP gas - 10"...

Nominal ratings Maximum output Gas type BTU/hr kW Normal burner Natural Gas (NG) Propane (LP) 6,300 6,300 1.85 1.85 Fast burner Natural Gas (NG) Propane (LP) 10,200 10,200 3.0 3.0 Total output Natural Gas (NG) Propane (LP) 16,500 16,500 4.85 4.85 Minimum output Gas type BTU/hr kW Normal burner Natur...

The combiset should have been ordered for connection to either natural gas or LP gas (propane). If the combiset is not configured for the proper type of gas connection please contact your Miele Dealer. Converting to another type of gas 43

Disposal of packing materials The cardboard box and packingmaterials are biodegradable andrecyclable. Please recycle. Ensure that any plastic wrappings,bags, etc. are disposed of safely andkept out of the reach of children.Danger of suffocation! Disposal of an old appliance Old appliances contain ma...