Microsoft GFK-1167B - Manual

Microsoft GFK-1167B – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – PLC CPUs; Figure 1. CSE 925 - Location of Major Features; User Memory; Installation should not be attempted without refer-
Page 3 – Make sure that rack power is off.; Figure 2. System Configuration, Serial Connection to; Serial Port; The IC697 CPU and I/O system is configured with IC641; Batteries
Page 4 – Reference; Programming Software User ’s Manual; Table 3. Ordering Information; Description

Loading the manual

64 MHz, 32-Bit Floating Point Central Processing Unit

1 Mbyte Memory, State Logic

IC697CSE925

PLC CPUs

GFK-1167B

August 1997

64 MHz, 32-Bit Floating Point Central Processing Unit 1 Mbyte Memory, State Logic

(

IC697CSE925

)

datasheet GFK-1167B

Features

Supports State Logic control programming

Supports floating point calculations

Single slot CPU.

12K inputs and outputs (any mix).

Up to 8K analog I/O.

0.4 microseconds per boolean function.

64 MHz, 80486DX2 microprocessor.

Supports IC660/IC661 and IC697 I/O products.

Programmed by AD641 and IC641 (MS-DOS

) software

products.

Provides 1 Mbyte of battery-backed memory in the same
slot.

Configurable data and program memory.

Battery-backed calendar clock.

Three position operation mode switch.

Password controlled access.

Remote programmer keyswitch memory protection

Four status LEDs.

Software configuration (No DIP switches or jumpers to
set).

Reference information inside front door.

In-system upgradable firmware.

Functions

The CSE 925 is a single slot programmable controller
CPU which provides State Logic control programming
and floating point calculations. The CSE 925 can be
programmed in State Logic, Relay Ladder Logic, and
C to perform real-time control of machines, processes,
and material handling systems.
The AD641 software products are used to program
the CSE 925 in State Logic; the IC641

(MS-DOS)

soft-

ware products are used to program in Relay Ladder
Logic and C. The IC641

(MS-DOS)

software is also

used to perform all configuration functions for the
CSE 925.
The CSE 925 communicates with I/O and smart op-
tion modules over the rack mounted backplane
(IC697CHS750, 782, 783, 790, 791) by way of the VME
C.1 Standard format.

PROGRAMMER

a45242

ÎÎÎÎÎ

OK
RUN
ENABLED

MEM PROTECT

STATE LOGIC

CPU

ÎÎ

ÎÎÎ

ÎÎ

B
A

T
T

MODULE
IC697CSE925
LABEL
44A726758-148R01

SERIAL PORT

USE THIS MODULE

CSE 925

OFF

TOP

REMOTE PROGRAMMER

ÎÎ

MODULE OK

ÎÎ

RUN

ÎÎ

OUTPUTS
ENABLED

ON = OK, ENABLED,

FRONT

RUN WITH

OUTPUTS

ENABLED

ÎÎ

RUN WITH
OUTPUTS
DISABLED

STOP

KEY POSITION

MODULE FUNCTION

64 MHz 32 BIT CENTRAL
PROCESSING UNIT WITH

BATTERY
CONNECTORS

INSTALL NEW

MEMORY PROTECT

ÎÎ

MEMORY

REMOTE

ONLY

RS-485
COMPATIBLE

PROTECT

PROTECTED

FLOA TING POINT MATH
COPROCESSOR, IN-SYSTEM
UPGRADABLE FIRMWARE

BATTERY BEFORE
UNPLUGGING OLD
BATTERY. USE
IC697ACC701

IN SLOT 1 ONLY.

ÎÎ

Î Î

ÎÎ

r MS-DOS is a registered trademark of Microsoft Corporation.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - PLC CPUs; Figure 1. CSE 925 - Location of Major Features; User Memory; Installation should not be attempted without refer-

64 MHz, 32-Bit Floating Point Central Processing Unit 1 Mbyte Memory, State Logic GFK-1167B PLC CPUs 2 August 1997 MEMORY PROTECT a45243 OPEN REPLACEMENT BATTERY CONNECTOR 1 MBYTE MEMORY BOARD CSE 925 CURRENTLY INSTALLED BATTERY CONNECTOR MEMORY PROTECT KEY SWITCH ÎÎ ÎÎ ÎÎ ÎÎ Î Î Î Î Î Î Î Î Î Î Î Î...

Page 3 - Make sure that rack power is off.; Figure 2. System Configuration, Serial Connection to; Serial Port; The IC697 CPU and I/O system is configured with IC641; Batteries

3 64 MHz, 32-Bit Floating Point Central Processing Unit 1 Mbyte Memory, State Logic GFK-1167B PLC CPUs August 1997 D Make sure that rack power is off. D Install the CSE 925 module in slot 1 of rack 0 (see Figure 2). D Turn on power. The module should power up and the top LED shouldblink. When the di...

Page 4 - Reference; Programming Software User ’s Manual; Table 3. Ordering Information; Description

64 MHz, 32-Bit Floating Point Central Processing Unit 1 Mbyte Memory, State Logic GFK-1167B PLC CPUs 4 August 1997 Table 1. References Reference Title 1 Programming Software User ’s Manual 2 Programmable Controller Reference Manual 3 Programmable Controller Installation Manual 4 State Logic Control ...

Other Microsoft Models

All Microsoft Other

Microsoft GFK-1167B - Manual

Table of Contents:

Summary

Other Microsoft Models