Page 3 - Contents
3 Contents Features ................................................................................................................................................................ 4 Installation and Initial Setup .........................................................................................
Page 4 - Features
4 Features The DLW (Dual Link / W aveform) Series is the latest addition to Marshall's expanding line of IMD-equipped monitors. ■ 1920 x 1200 Full Resolution 17” Panel The V-R171X-DLW features an all-digital TFT-MegaPixel active matrix LCD system with 1920x1200 native resolution. The LCD panel featu...
Page 5 - Installation and Initial Setup; Unpacking; Installation
5 Installation and Initial Setup ■ Unpacking Carefully unpack the V-R171X-DLW monitor and verify that the following items are included: • V-R171X-DLW Monitor • V-PS12-5V-1 Power Supply with Twist-Lock Connector • Operating Instructions Inspect the unit for any physical damage that may have occurred ...
Page 6 - Front Panel Features
6 Front Panel Features Power Button Turn the monitor off or on by pressing the power button. The LED on the power button is at maximum illumination when the unit is OFF. The LED is at minimum illumination when the unit is on. Input Channel Buttons Pressing SDI 1 or SDI 2 will select HDSDI-SDI Video ...
Page 7 - Rear Panel Features
7 Rear Panel Features RS-422/485 Serial Interface The RS-422/485 ports are used to remotely control the IMD or all V-R171X-DLW features, using a variety of industry standard protocols. (Note: Connector/pin-out may need to be adapted depending on protocol and controlling device used.) Only one connec...
Page 8 - Compatible Input Formats
8 Compatible Input Formats The following SDI standards are supported by the V-R171-DLW: 525i, 625i 720p (60, 59.94, 50) 720p (30 / 29.97) 1035i (60 / 59.94) 1080i (60 / 59.94 / 50) 1080psF (24 / 23.98) 1080p (30 / 29.97 / 25 / 24 / 23.98) The following 3G-SDI standards are supported by the V-R171-DL...
Page 9 - DLW Monitor Layouts
9 DLW Monitor Layouts The V-R171X-DLW has 4 possible layouts, Multi mode, Vectorscope mode, Waveform mode and Full Screen Video mode. Each press of the LAYOUT Button will change the current mode to next available mode. Default Multi mode Layout Vectorscope Mode
Page 12 - MAIN MENU AND NAVIGATION; Marker Setup Submenu
12 On-Screen Menu (continued) MAIN MENU AND NAVIGATION Access and navigate the main menu using the RotoMenu™ knob: Using the RotoMenu knob • Press the RotoMenu™ knob to enter the main menu. • Rotate the knob to scroll up or down in the main menu or each submenu. • Press the RotoMenu™ knob to enter a...
Page 14 - Video Config Submenu
14 ■ Marker Background Use this setting to choose how selected markers are displayed on the screen: • Off The marker is superimposed on the complete image. • 50% Gray Screen area beyond the marker is shown at 50% intensity. • Black Screen area beyond the marker is shown as black. Example (80% Marker...
Page 15 - Monochrome Mode; Aspect Ratio Settings
15 ■ Monochrome Mode Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale picture. ■ Blue-Only Mode Use this setting to enable Blue-Only mode. This mode displays only the blue color component of the image, switching off the red and green compon...
Page 16 - Curtain Color
16 • In Full Screen (16:10) mode, images are scaled to fill the entire 16:10 screen (1920 x 1200). In this mode, all OSD features are superimposed on the image. Note that when using a 16:9 input image in this mode, the image will be vertically stretched by approximately 10%. The diagrams on the foll...
Page 19 - OSD Config Submenu; IMD State
19 OSD Config Submenu Use the OSD Configuration submenu to select a variety of information to be displayed on the screen. ■ IMD State Use this setting to turn the IMD text display on or off. This setting affects both fixed string IMD text and remote IMD text commands. ■ Status Display Use this setti...
Page 22 - IMD Config Submenu; Overview
22 IMD Config Submenu ■ Overview The V-R171X-DLW features an In-Monitor Display (IMD) with the ability to display on-screen text and tally in three colors. IMD text, color, and alignment can be assigned to each screen locally using menu options (see below). Alternately, IMD text and tally can be rem...
Page 25 - Closed Captioning Submenu; Mode
25 On-Screen Menu (continued) Closed Captioning Submenu Use the Closed Captioning submenu to select the type of captioning stream you would like to decode. ■ Mode The DLW monitor series provides support for three types of Closed Captioning Modes: 608, 708 and 708 (608 Comp.). Use this section to cho...
Page 26 - Waveform Mode
26 Wave/Vector Submenu Use the W ave/Vector submenu to change the location of the W aveform Monitor and Vectorscope, as well as the data displayed on the W aveform monitor or the Vectorscope on the V-R171X-DLW monitor. The W aveform Monitor can also be customized to conform to different scales, to d...
Page 27 - Waveform Scale
27 • RGB Parade The R (shown in Red), G (shown in Green) and B (shown in Blue) components of the signal are displayed from left to right. • RGB Overlay The RGB components of the signal are overlaid. ■ Waveform Scale Use the W aveform scale option to switch between different graticule units on the Wa...
Page 28 - Ancillary Submenu
28 ■ Vectorscope Targets Use the Vectorscope Targets option to set your Vectorscope targets up for 75% or 100% color bar signals. You can also set your Vectorscope Targets to the OFF position. ■ Overlay Position Use the Overlay Position option to place the W aveform, Vectorscope and Audio Level disp...
Page 29 - SERVICE SUBMENU; Software Version Display
29 SERVICE SUBMENU ■ Software Version Display The Main Board, Keypad, and FPGA software version numbers are displayed. . The following information is displayed: • rel: Release Package version number • ipa Input processor firmware • dlw FPGA Version • ipap Product Type • kp Keypad version number Serv...
Page 30 - Specifications
30 Specifications ■ PANEL Screen Size 17” Diagonal Display Area (h x v) 367.20 x 229.50 mm Aspect Ratio 16:10 Native (4:3/16:9 Modes) Pixels 1920 x RGB x 1200 Color Depth 8-bit Viewing Angle (h x v) 140° x 120° Brightness 400 cd/m 2 Contrast Ratio 600:1 Dot Pitch (h x v) 0.064 x 0.191 mm Pixel Pitch...
Page 31 - Maintenance; Screen Cleaning; Warranty
31 Specifications (continued) Maintenance ■ Screen Cleaning Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-fiber cloth can also be used using only non-abrasive and ammonia-free cleaning agents. Do not use paper towels. Paper towel f...
