Marantz RX8001 - Manual

Marantz RX8001

Marantz RX8001 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
Page: / 20

Table of Contents:

  • Page 4 – Contents
  • Page 5 – LI; Before You Start; Configure; Note
  • Page 6 – Unpacking the Extender
  • Page 7 – Configuring the Extender; section of your region.; Stand-alone Connection; Plug in the Extender’s; power adapter; Use the default; switch; settings of the Extender:; Configuration switch can be set to a different RF channel.; Configure the Control Panel’s; configuration file; so that the Control Panel can work; Network Connection; There are two ways to use the Extender in a network:; Wired; Wireless; connection; When you set up a Wireless
  • Page 8 – To ensure optimal performance, use a dedicated network for all
  • Page 9 – Configuring the Extender through a Router; The Configuration Tool opens in the browser.; Installing the Extender; Warning; Connecting the Extender to A/V equipment; Tip
  • Page 10 – Adjusting the Power Level of the IR Outputs; Support; Troubleshooting; What Do the LEDs Indicate?; There is an IP conflict; If the problem persists, check the router settings.; The IP address cannot be determined; using; • When; configuring
  • Page 11 – The Extender cannot communicate with the wireless network; The WiFi LED is red; Finding the Exact Location of an A/V component’s IR Receiver; Remove the protective tape of the Dual IR emitters.; Operating A/V components with the Extender; The A/V components do not respond to commands from the Extender; Make sure you use a quality access point.; There are duplicate Extender IDs; You can use up to 16 different Extenders in the same; The Busy LED blinks green when the Control Panel is not in use
  • Page 12 – Resetting the Extender; Firmware Update; Updating the Extender with the configuration cable; The; Updating the Extender through a router
  • Page 13 – Select the Extender that you want to configure and click on the; in the left navigation pane.; When your Extender is; not recognized by the Extender Discovery; tool, update the Extender; Specifications; Wireless Extender User Guide
  • Page 14 – FCC Compliancy; CAUTION; Notice for Canada / Remark pour le Canada; Regulations According to R&TTE; Declaration; IFU Approbation / Safety Content
  • Page 15 – Marking; ii
  • Page 16 – iii
  • Page 17 – iv
  • Page 20 – is a registered trademark.
Loading the manual

Model RX8001 User Guide

Wireless Extender

ENGLISH

FRANÇAIS

ESPAÑOL

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 4 - Contents

1 RX8001 User Guide RX8001 User Guide Contents Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Configuring the Extender . . . . . . . . . . . ...

Page 5 - LI; Before You Start; Configure; Note

E N G LI S H 2 RX8001 User Guide RX8001 User Guide Before You Start The Wireless Extender is an important element of the RC9001 and makes it possible to control A/V equipment via RF in the entire house.In order to use the Extender in a wireless Network: • Configure the Extender: connect it to the PC...

Page 6 - Unpacking the Extender

3 RX8001 User Guide Unpacking the Extender Wireless Extender Front Panel Antenna Configuration switch• In Stand-alone Mode: changes the RFchannel. • In Network Mode: indicates theconnection type. IP address Power input 4 IR outputs 4 dipswitches forthe IR outputs Back Panel Extender ID switch Ethern...

Other Marantz Models

All Marantz Other