Page 2 - WARNING
1 IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with a dry cloth.7. Do not block any of the ventilation openings. Install in acc...
Page 3 - (Informations de Sécurité Supplémentaires); AVERTISSMENT; PRÉCAUTIONS IMPORTANTES DE SÉCURITÉ
2 1. Lire ces instructions.2. Garder ces instructions.3. Respecter tous les avertissements.4. Suivre toutes les instructions.5. Ne pas utiliser cet appareil près de l’eau.6. Nettoyer seulement avec un chiffon sec.7. Ne pas boucher les ouvertures d’aération. Installer selon les instructions du fabric...
Page 4 - Precautions; CAUTION; Warnings and Safety Precaution; Important Information
3 Precautions Please read this manual carefully before using your plasma monitor andkeep the manual handy for future reference. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DONOT REMOVE COVER. NO USER-SERVICEABLEPARTS INSIDE.REFER SERVICING TO QUALIFIED S...
Page 5 - Précaution; ATTENTION; Recommandations importantes
4 Précaution Veuillez lire avec attention ce manuel avant d’utiliser le moniteur à plasmaet le conserver accessible pour s’y référer ultérieurement. ATTENTION .. RISQUE D’ELECTROCUTION NE PAS OUVRIR ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION, NE PAS OUVRIR LE BOITIER. A L’INTERIEUR,AUCUNE PI...
Page 6 - Caution; for PD; Warning; • Connect the equipment into an outlet on a circuit; A NOTE ABOUT RECYCLING
5 NOTE:When you use the power cable (supplied), use thesupplied ferrite cores. Set the ferrite cores (supplied)on both ends of the power cable (supplied), and thenuse the bands (supplied) to fasten the ferrite cores(supplied) to the power cable (supplied). If you do notthis, this monitor will not co...
Page 7 - Le matériel d’emballage de cet appareil est; Avertissement; Attention; para PD; AVERTISSEMENT; Milieu de fonctionnement: PD6001; F à
6 Recommandations importantes ATTENTION Lorsque vous diposez de piles / batteries usées,v e u i l l e z v o u s c o n f o r m e r a u x n o r m e sg o u ve r n e m e n t a l e s o u e nv i r o n n e m e n t a l e s e nvigueur dans votre pays ou région. REMARQUE CONCERNANTLE RECYCLAGE Le matériel d’e...
Page 8 - Contents; Contents of the Package; , Manganese battery for remote; Options
7 Contents IMPORTANT SAFETY INSTRUCTIONS ..................... 1PRÉCAUTIONS IMPORTANTES DE SÉCURITÉ ........... 2Important Information ...................................... 3Recommandations importantes ......................... 4Important Information ...................................... 5Recomman...
Page 9 - * Do not touch or hold the screen face when carrying the unit.; Installation
8 50 mm (2") Wall Wall 50 mm (2") 50 mm (2") 50 mm (2") 50 mm (2") You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:* While it is upright. (See Drawing A)* As it is laid down with the screen face down (See Drawing B). Lay the pro...
Page 10 - Using the remote control; Battery Installation and Replacement; Operating Range; Cable Management; To attach
9 ON/STANDBY Approx. 7 m / 23 ft Using the remote control Battery Installation and Replacement Designated batteries:Please use size AAA (R03) or AAA (LR03).Insert the 2 “AAA” batteries, making sure to set them inwith the proper polarity.1. Press and open the cover. CAUTION • Use only the specified b...
Page 11 - Turns the monitor’s power on and off.; Front View; Adjusts the volume. Functions as the CURSOR (; Part Names and Function
10 MENU INPUT/ EXIT VOLUME ON/STANDBY MENU INPUT / EXIT VOLUME ON/STANDBY 4 5 6 7 1 3 2 q Power Turns the monitor’s power on and off. w Remote sensor window Receives the signals from the remote control. e ON/STANDBY indicator When the power is on ............................. Lights green.When the p...
Page 12 - Rear View/ Terminal Board
13 A AC IN Connect the included power cord here. B EXT SPEAKER L and R Connect speakers (optional) here. Maintain the correctpolarity. Connect the (positive) speaker wire to the EXT SPEAKER terminal and the (negative) speaker wire to the EXT SPEAKER terminal on both LEFT and RIGHT channels.Please re...
Page 13 - Remote Control
14 q POWER ON/STANDBY Switches the power on/standby.(This does not operate when the ON/STANDBYindicator of the plasma is off.) w OFF TIMER Activates the off timer for the unit. e DISPLAY Displays the source settings on the screen. r WIDE Automatically detects the signal and sets the aspectratio.WIDE...
Page 14 - Basic Operations; To change the size of the picture:
15 Basic Operations POWER To turn the unit ON and OFF: 1. Plug the power cord into an active AC power outlet.2. Press the Power button (on the unit). The monitor’s ON/STANDBY indicator turns red and thestandby mode is set. 3. Press the POWER ON button (on the remote control) to turn on the unit.The ...
Page 15 - Wide Screen Operation; When viewing videos or digital video discs; ANAMORPHIC size screen; WIDE Operations
16 Wide Screen Operation (manual) With this function, you can select one of seven screen sizes. When viewing videos or digital video discs 1. Press the WIDE button on the remote control.2. Within 3 seconds ... Press the WIDE button again.The screen size switches as follows: → NORMAL → ANAMORPHIC → S...
Page 16 - * “ V G A ” , “ S V G A ” a n d “ S X G A ” a r e r e g i s t e r e d; When displaying enhanced split screen:
17 Information Supported resolution See page 39, 42 and 45 for details on the display outputof the various VESA signal standards supported by themonitor. When 852 (848) dot 480 line wide VGA* signals with a vertical frequency of 60 Hz andhorizontal frequency of 31.7 (31.0) kHz are in-put Select an a...
Page 17 - SPLIT SCREEN Operations; * There may be some RGB-input signals that may not be
18 Information Split screen operations may not function depending onthe combination of input signals. In the table below,“ ” means Yes, “ ” means No. Split screen operations may not function d e p e n d i n g o n t h e f r e q u e n c y o f t h e R G Bsignals. SPLIT SCREEN Operations Showing a coupl...
Page 18 - Operations in the Picture-in-picture mode; Selecting the input signals to be displayed
19 Operations in the Picture-in-picture mode To move the position of the sub screen, press the cursor or button. To change the size of the sub screen, press the button. VIDEO1 PC/RGB A B VIDEO1 PC/RGB A B VIDEO1 PC/RGB A B VIDEO1 PC/RGB A B button button button button To make the desired picture act...
Page 19 - Menu Operations; The main menu disappears by pressing the EXIT; OSM; Information; * The actual screen may be dif ferent from the ones
20 Menu Operations The following describes how to use the menus and theselected items.1. Press the MENU/ENTER button on the remote control to display the MAIN MENU. M A I N M E N U P I C T U R E A U D I O I M A G E A D J . S E T U P F U N C T I O N S I G N A L I N F O . SEL. EXIT MENU/ENTER OK EXIT ...
Page 20 - Menu Tree
21 Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET REFERENCE PICTURE PICTURE MEMORY OFF/MEMORY1-6 YES 23 CONTRAST ←→ 0 ← 52 → 72 YES 23 BRIGHTNESS ←→ 0 ← 32 → 64 YES 23 SHARPNESS ←→ 0 ← 16 → 32 YES 23 COLOR ←→ 0 ← 32 → 64 YES 23 TINT R ←→ G 0 ← 32 → 64 YES 23 NR OFF/NR-1/NR-2/NR-3 YES 23 C...
Page 22 - Picture Settings Menu; Storing picture settings; Example: Storing picture settings at MEMORY1; Adjusting the picture; Example: Adjusting the contrast; Reducing noise in the picture
23 Picture Settings Menu Storing picture settings This function allows you to store in memory the currentinput signal and PICTURE menu settings and to recallthese settings when necessary.There are six picture memories, and notes of up to 15characters can be added to each. Example: Storing picture se...
Page 23 - Setting the color temperature; Example: Setting “HIGH”; Adjusting the color to the desired level; Setting the picture to suit the movie; Example: Setting the “CINEMA MODE” to “OFF”; Example: Setting the “THEATER1” mode
24 Setting the color temperature Use this procedure to set color tone produced by the plasmadisplay. Example: Setting “HIGH” On “COLOR TEMP.” of “PICTURE” menu, select “HIGH”. SEL. ADJ. RETURN P I C T U R E P I C T U R E M E M O R YC O N T R A S TB R I G H T N E S SS H A R P N E S SC O L O RT I N TN...
Page 24 - Adjusting the colors; Example: Adjusting the color tune for blue; Adjusting the pedestal level (black level); Changing the Gamma Curve; Set “ADVANCED OSM” to “ON” in the FUNCTION menu.; Making the Low Tone adjustments; Example: Setting “MODE2”
25 Adjusting the colors Use this procedure to adjust hue and color density for red,green, blue, yellow, magenta and cyan without changingthe white point.You can accentuate the green color of trees, the blue ofthe sky, etc. Example: Adjusting the color tune for blue Set “ADVANCED OSM” to “ON” in the ...
Page 25 - Audio Settings Menu; Example: Adjusting the bass; Set “AUDIO INPUT” on the AUDIO menu correctly.; Example: Setting “AUDIO INPUT1” to “VIDEO2”; Image Adjust Settings Menu; Adjusting the Auto Picture; FINE PICTURE; Setting the Underscan
26 Audio Settings Menu A d j u s t i n g t h e t r e b l e , b a s s a n d l e f t / r i g h tbalance and audio input select The treble, bass and left/right balance can be adjusted tosuit your tastes. Example: Adjusting the bass On “BASS” of “AUDIO” menu, adjust the bass. SEL. ADJ. RETURN EXIT A U D...
Page 26 - SET UP Settings Menu; Setting the language for the menus; Example: Setting the menu display to “DEUTSCH”
27 SET UP Settings Menu Setting the language for the menus The menu display can be set to one of eight languages. Example: Setting the menu display to “DEUTSCH” On “LANGUAGE” of “SET UP” menu, select “DEUTSCH”. SEL. ADJ. RETURN S E T U P L A N G U A G ED V D / H D 1 I N P U TD - S U B I N P U TH D S...
Page 27 - Setting the black level for HDMI signal; Example: Setting the “HDMI SET UP” mode to “LOW”; Setting the video signal format; Example: Setting the color system to “3.58 NTSC”; Example: Setting “BACK GROUND” to “BLACK”
28 Information RGB SELECT modes AUTO: Select the suitable mode for the specifications of input signals as listed in the table “Computer inputsignals supported by this system” on page 39, 42 and45. The others: The available resolutions are shown. See page 39, 42 and 45 for the details of the aboveset...
Page 28 - etting the screen size for S1/S2 video input; et “ADVANCED OSM” to “ON” in the FUNCTION menu.; nformation; Adjusts the screen size automatically according; Setting the gray level for the sides of the screen; Example: Setting “GRAY LEVEL” to “5”; Turning on/off the menu display; Example: Turning the DISPLAY OSM off; Setting the position of the menu; Example: Set the position to “TOP CENTER”; The informations on screen size, volume control,
29 etting the screen size for S1/S2 video input f the S-video signal contains screen size information, the mage will be automatically adjusted to fit the screen when his S1/S2 is set to AUTO.his feature is available only when an S-video signal is nput via the VIDEO2 terminal. xample: Setting “S1/S2”...
Page 29 - Resetting to the default values; Refer to page 21 for items to be reset.; Example: Turning the power management function on; Remote ID; Example: Setting to “1”; Function Settings Menu; Setting the menu mode; Example: Setting “ON”
30 Resetting to the default values Use these operations to restore all the settings (PICTURE,AUDIO, IMAGE ADJUST, SET UP, etc.) to the factorydefault values. Refer to page 21 for items to be reset. On “ALL RESET” of “SET UP” menu, select “ON”, thenpress the MENU/ENTER button. SEL. ADJ. RETURN S E T ...
Page 30 - Setting the Input Skip; Example: Setting “ZOOM NAV” to “S BY S”; Example: Setting “DISPLAY” to “FADE”; Displaying still images in the sub screen
31 Setting the Input Skip When this is ON, signals which are not present will beskipped over and only pictures whose signals are beingtransmitted will be displayed.This setting is valid only for the INPUT/EXIT button onthe unit. Example: Set to “ON” Set “ADVANCED OSM” to “ON” in the FUNCTION menu. O...
Page 31 - Reducing image retention
32 Reducing image retention The brightness of the screen, the position of the picture,positive/negative mode and screen wiper are adjusted toreduce image retention. Set “ADVANCED OSM” to “ON” in the FUNCTION menu. O n “ P D P S AV E R ” o f “ F U N C T I O N ” m e n u , s e l e c t“MANUAL”, then pre...
Page 32 - Setting Closed Caption
33 INVERSE/WHITE Use this to set the inverse mode or to display a whitescreen. Example: Setting “INVERSE/WHITE” to “WHITE” On “INVERSE/WHITE” of “PDP SAVER” menu, select“WHITE”. SEL. ADJ. RETURN EXIT P D P S AV E R P E A K B R I G H TO R B I T E RI N V E R S E / W H I T ES C R E E N W I P E RS O F T...
Page 33 - Reducing the brightness of Closed Caption; Example: Setting “NORMAL”; PICTURE IN PICTURE; VOLUME settings; Signal Information Menu; Setting the power on mode; Example: Setting the input mode to “VIDEO2”
34 Reducing the brightness of Closed Caption Use this to reduce the brightness of Closed Caption. Example: Setting “NORMAL” Set “ADVANCED OSM” to “ON” in the FUNCTION menu. On “CAPTION CONT” of “FUNCTION” menu, select“NORMAL”. SEL. ADJ. RETURN EXIT F U N C T I O N A D VA N C E D O S MP O W E R M G T...
Page 34 - Connections are made as described below.; Communication Parameters; Asynchronous; External Control Pin Assignments; Plasma monitor REMOTE IN
35 Application These specifications cover the communications control ofthe plasma monitor by external equipment. Connections Connections are made as described below. Connector on the plasma monitor side: EXTERNALCONTROL connector.Use a crossed (reverse) cable. Type of connector: D-Sub 9-pin male 1 5...
Page 35 - • The transmit frequency of the remote control of STB is; Connection with STB; Connection Example: Connecting an STB
36 Following is the connection example of STB (Set-top Box)using the REMOTE IN/OUT connectors of the plasmamonitor. Consult your dealer about the actual connectionand operation. * Connection Example • STB has the REMOTE IN connector.• The pin assignment of the REMOTE IN connector of STB is same as t...
Page 36 - Troubleshooting
37 Remedy • If there are no abnormalities in the image and sound, the noise is caused by the cabinet reacting tochanges in temperature. This will not affectperformance. • Leave some space between the display and the connected components. • Replace both batteries with new ones. • Plug the monitor’s p...
Page 38 - Table of Signals Supported; Supported resolution: PD6001; Computer input signals supported by this system
45 Table of Signals Supported Supported resolution: PD6001 • When the screen mode is NORMAL, each signal is converted to a 1024 dots ⳯ 768 lines signal. (Except for * 2, 3 ) • When the screen mode is ANAMORPHIC, each signal is converted to a 1365 dots ⳯ 768 lines signal. (Except for * 2 ) Computer i...
Page 39 - D E C L A R A T I O N O F C O N F O R M I T Y; Equipment Classification:; We hereby declare that the equipment specified above
46 *1 Only when using a graphic accelerator board that is capable of displaying 852 ⳯ 480. *2 The picture is displayed in the original resolution.*3 The aspect ratio is 5:4. This signal is converted to a 960 dots ⳯ 768 lines signal. *4 Normally the RGB select mode suite for the input signals is set ...
Page 40 - is a registered trademark.
09/2006 00M25AV851250 mzh-g Printed in Japan www.marantz.com You can find your nearest authorized distributor or dealer on our website. is a registered trademark. PD4201̲Cover̲NEW 06.9.7, 4:41 PM Page 2 Adobe PageMaker 6.5J/PPC
