Page 2 - SPECIFICATIONS; SAVE THESE INSTRUCTIONS.
2 ENGLISH (Original instructions) SPECIFICATIONS Model HM1304B Blows per minute 1,450 Overall length 831 mm (32 - 3/4") Net weight 18.1 kg (39.8 lbs) • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications ma...
Page 3 - Service; SPECIFIC SAFETY RULES; Hold the tool firmly with both hands.
3 17. Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. 18. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures re...
Page 4 - Switch action; ASSEMBLY
4 11. Do not point the tool at any one in the area when operating. The bit could fly out and injure someone seriously. 12. Do not touch the bit or parts close to the bit immediately after operation; they may be extremely hot and could burn your skin. 13. Some material contains chemicals which may be...
Page 5 - Installing or removing the bit; OPERATION
5 To secure the handle at a fixed position, first loosen the nut and swing the handle to the desired position for use. Then tighten the nut firmly. If the set bolt turns together with the nut when you secure the nut, see that the projecting portion of the side handle fits into the notch on the head ...
Page 6 - ACCESSORIES
6 Replacing carbon brushes 1 2 3 001146 When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replaced. Keep the carbon brushes clean and free to slip in the holders. Both ...
Page 7 - MAKITA LIMITED ONE YEAR WARRANTY
7 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during th...
Page 8 - SPÉCIFICATIONS; Zone de travail
8 FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle HM1304B Nombre de frappes par minute 1 450 Longueur totale 831 mm (32 - 3/4") Poids net 18,1 kg (39,8 lbs) • Étant donné l'évolution constante de notre programme de recherche et de développement, les spécifications contenues dans ce manue...
Page 10 - Symboles
10 USB009-2 RÈGLES DE SÉCURITÉ PARTICULIÈRES NE vous laissez PAS tromper (au fil d'une utilisation répétée) par un sentiment d'aisance et de familiarité avec le produit, en négligeant le respect rigoureux des règles de sécurité qui accompagnent le marteau. L'utilisation non sécuritaire ou incorrecte...
Page 11 - Interrupteur; ASSEMBLAGE; Installation et retrait du embout
11 DESCRIPTION DU FONCTIONNEMENT ATTENTION: • Assurez-vous toujours que l'outil est hors tension et débranché avant de l'ajuster ou de vérifier son fonctionnement. Interrupteur 1 2 003892 ATTENTION: • Avant de brancher l'outil, assurez-vous toujours que la gâchette fonctionne correctement et revient...
Page 12 - Remplacement des charbons
12 (2) Pour les forets sans embase 12 3 4 5 003895 Faites pivoter le dispositif de retenue vers l'arrière et légèrement vers le bas. La partie entaillée du foret faisant face à l'arbre du dispositif de retenue, insérez le foret à fond dans le porte-outil. Faites ensuite pivoter le dispositif de rete...
Page 13 - ACCESSOIRES; GARANTIE LIMITÉE D’UN AN MAKITA; Politique de garantie
13 situation exige toutefois que vous graissiez vous-même l'outil, procédez alors comme suit. Laissez tourner l'outil pendant quelques minutes pour le faire chauffer. Arrêtez-le et débranchez-le. Retirez le bouchon du carter au moyen d'une clé hexagonale, puis remplissez de graisse fraîche (60 g; 2 ...
Page 14 - ESPECIFICACIONES; Área de trabajo
14 ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo HM1304B Especificaciones eléctricas en México 120 V 13 A 50/60 Hz Golpes por minuto 1 450 Longitud total 831 mm (32 - 3/4") Peso neto 18,1 kg (39,8 lbs) • Debido a nuestro programa continuo de investigación y desarrollo, las especific...
Page 17 - Símbolos; Accionamiento del interruptor; ENSAMBLE; Instalación o extracción del cincel.
17 USD203-2 Símbolos A continuación se muestran los símbolos utilizados para la herramienta. ・ volts o voltios ・ amperes ・ hertz ・ corriente alterna ・ Construcción clase II ・ revoluciones o alternaciones por minuto ・ número de percusiones DESCRIPCIÓN DEL FUNCIONAMIENTO PRECAUCIÓN: • Asegúrese siempr...
Page 18 - Reemplazamiento de las escobillas de carbón
18 (1) Para cincel con collarín 1 2 3 4 5 003894 Gire la pinza sujetadora hacia atrás y apenas hacia abajo. Inserte el cincel en la herramienta hasta que haga tope. Para sujetar el cincel firmemente, coloque la pinza sujetadora nuevamente en su posición original. PRECAUCIÓN: • Siempre asegúrese de q...
Page 19 - Lubricación
19 Utilice un destornillador para quitar las tapas de los portaescobillas. Extraiga las escobillas gastadas, inserte las nuevas y vuelva a colocar los tapas. 1 2 003897 Vuelva a instalar las placas de soporte firmemente. Lubricación Esta herramienta no necesita lubricación por hora ni diaria dado qu...
Page 20 - Política de garantía
20 GARANTÍA LIMITADA MAKITA DE UN AÑOÉsta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de ...
Page 24 - Makita Corporation
24 Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints,• crystalline silica fro...