Makita DP3003 - Manual - manualsarea.com

Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all; SAVE THESE INSTRUCTIONS; Work Area; Electrical Safety

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in...

Page 4 - SERVICE

4 model. Accessories that may be suitable for one tool, may become hazardous when usedon another tool. SERVICE 23. Tool service must be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnelcould result in a risk of injury. 24. When servicing a tool...

Page 5 - SPECIFIC SAFETY RULES

5 SPECIFIC SAFETY RULES USB001-2 DO NOT let comfort or familiarity with product (gained fromrepeated use) replace strict adherence to drill safety rules. Ifyou use this tool unsafely or incorrectly, you can suffer seriouspersonal injury. 1. Hold tool by insulated gripping surfaceswhen performing an ...

Page 6 - SYMBOLS

6 SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... volts A ....................... amperes Hz ..................... hertz ................ alternating current .................... no load speed .................... Class II Construction .../min .................

Page 8 - Hook; ASSEMBLY

8 Hook When using the hook, pull it out in A direction and then pushit in B direction to secure in place.When not using the hook, return it back to its initial positionby following the above procedures in reverse. ASSEMBLY CAUTION: • Always be sure that the tool is switched off andunplugged before c...

Page 9 - Installing or removing drill bit

9 Installing or removing drill bit For Model DP3003, DP4001, DP4003 Hold the ring and turn the sleeve counterclockwise to openthe chuck jaws. Place the bit in the chuck as far as it will go.Hold the ring firmly and turn the sleeve clockwise to tightenthe chuck.To remove the bit, hold the ring and tu...

Page 10 - OPERATION; Holding tool; Drilling in wood

10 OPERATION Holding tool When drilling a large hole with a hole saw, etc., the side grip(auxiliary handle) should be used as a brace to maintain safecontrol of the tool. Grasp the rear handle and the front grip firmly when startingor stopping the tool, since there is an initial and final reaction. ...

Page 12 - Memo

Page 14 - MAIL THIS PORTION; Your answers to the following questions are appreciated.; Please return this portion by facsimile or mail.

14 1. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( ) 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog Radio Exhibition From Friend Previous Usage Other ( ) 2. Use of the ...

Page 15 - FACTORY SERVICE CENTERS; RETAIN THIS PORTION FOR YOUR RECORDS

15 FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211...

Page 16 - WARNING; MAKITA LIMITED ONE YEAR WARRANTY; Warranty Policy; Makita Corporation

WARNING Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm. Some examplesof these chemicals are:• lead from lead-based paints, • crystalline sili...

Makita DP3003 - Manual

Table of Contents:

Other Manuals for Makita DP3003

Summary

Other Makita Drills Models