Page 2 - Thank you for purchasing a MAKITA product!; RE Y; Packing; Table of contents; Page
2 Thank you for purchasing a MAKITA product! Congratulations on choosing a MAKITA chain saw! We are con fi dent that you will be satis fi ed with this modern piece of equipment. The DCS3410TH (Tophandle) is a very light and handy chain saw with the handle on the top. This model was developed especia...
Page 3 - Symbols; Delivery inventory
3 In case one of the parts listed should not be included in the delivery inventory, please consult your sales agent. Symbols You will notice the following symbols on the chain saw and in the instruction manual: Chaine brake Fuel and oil mixture Chain oil Saw chain oil adjustment screw Direction of c...
Page 4 - SAFETY PRECAUTIONS; General precautions; Protective equipment
4 4 5 6 7 1 2 3 1 SAFETY PRECAUTIONS Power chain saws This power chain saw may be used only for sawing wood out of doors. It is intended for the followung uses depending on its class: - Professional and mid-class: Use on small, medium and large trees: felling, limb removal, cutting to length, thinni...
Page 5 - Putting into operation
5 5 Fuels / Refuelling - Stop the engine before refuelling the chain saw. - Do not smoke or work near open fi res (5). - Let the engine cool down before refuelling.- Fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products. Always wear prot...
Page 6 - Kickback; In order to prevent kickback, follow these rules:; Working behavior/Method of working; For felling and crosscuts the spike bar (
6 Kickback - When working with the chain saw dangerous kickbacks may occur. - Kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (10). - Before the saw chain enters the cut, it can slip to the side or jump (caution: high risk of kickback)...
Page 8 - Transport and storage; Maintenance; and pull out the plug cap.; First aid; When calling for help, give the following information:; SERVICE
8 Transport and storage - When changing your location during work switch off the chain saw and actuate the chain brake in order to prevent an inadvert-ent start of the chain. - Never carry or transport the chain saw with the chain running. - When transporting the chain saw over long distances the gu...
Page 9 - Denomination of components; Technical data
9 Denomination of components 1 Rear handle 2 Safety locking button (throttle lock) 3 Throttle lever 4 Hand guard (release for chain brake) 5 Spike bar (accessories) 6 Chain 7 Guide bar 8 Chain protection cover 9 Retaining nuts 10 Chain catch (safety device) 11 Sprocket guard 12 Muf fl er 13 Spark pl...
Page 10 - PUTTING INTO OPERATION; Mounting the guide bar and saw chain
10 5 6 Position the guide bar ( 7 ). Make sure that the pin ( 8 ) of the chain tightener is in the hole on the guide bar. Turn the chain adjusting screw ( 5 ) to the left (counter clockwise) until the pin ( 6 ) is at the left stop. A C D PUTTING INTO OPERATION CAUTION: Before doing any work on the g...
Page 11 - Tightening the saw chain
11 3 2 13 9 9 12 9 10 11 F Pull the chain ( 9 ) around the sprocket nose ( 12 ) of the guide bar in the direction of the arrow. Lift the chain ( 9 ) over the sprocket ( 10 ). Using your right hand, guide the chain into the top guide groove ( 11 ) on the guide bar. Note that the cutting edges along t...
Page 12 - Checking the chain tension; Chain brake; Doing so; Engaging the chain brake; automatically
12 Checking the chain tension The tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be easily turned by hand. While doing so the chain brake must be released. Check the chain tension frequently - new chains tend to get longer during use! When c...
Page 13 - Chain oil; Fuel; Fuel mixture; The Storage of Fuel
13 Gasoline + 1000 cm 3 (1 litre) 20 cm 3 20 cm 3 5000 cm 3 (5 litres) 100 cm 3 100 cm 3 10000 cm 3 (10 litres) 200 cm 3 200 cm 3 OIL Chain oil Use an oil with adhesive additive for lubricating the chain and guide bar. The adhesive additive prevents the oil from being fl ung off the chain too quickl...
Page 14 - Refuelling; FOLLOW THE SAFETY PRECAUTIONS!; Be careful and cautious when handling fuels.; Lubricating the chain; Check only when the engine; waste oil; NEVER USE WASTE OIL
14 Refuelling FOLLOW THE SAFETY PRECAUTIONS! Be careful and cautious when handling fuels. The engine must be switched off! Thoroughly clean the area around the caps, to prevent dirt from getting into the fuel or oil tank. Unscrew the cap and fi ll the tank with fuel (fuel/oil mixture) or chain oil a...
Page 15 - Adjusting the chain lubrication; The engine must be switched off.; Checking the chain lubrication
15 2 3 1 Adjusting the chain lubrication The engine must be switched off. You can adjust the oil pump feed rate with the adjusting screw ( 1 ). The amount of oil can be adjusted using the universal wrench. Recommended settings: - 25 cm guide bar - 30 cm guide bar - 35 cm guide bar - 40 cm guide bar ...
Page 16 - Stopping the engine; Starting the engine
16 Cold start: Prime the fuel pump ( 6 ) by pressing it several times until you can see fuel in the pump. Move the short-circuit switch ( 3 ) forward in the direction of the arrow. Turn the choke lever ( 5 ) up (see “Cold start” illustration). This simultaneously actuates the half-throttle lock. Slo...
Page 18 - Adjusting the carburetor
18 8 9 Adjusting the carburetor (only for not EU-countries) E Carburetor adjustment is necessary for optimum engine performance, for safer and more economical operation. The engine should be warm, the air fi lter clean, and the chain properly tensioned. Have carburetor adjustment done by an authoris...
Page 19 - MAINTENANCE; Sharpening the saw chain; The chain needs sharpening when:
19 Proper sharpening: CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare-parts list) ! All cutters must be of the same length (dimension a). Cutters with different lengths result in rough running of the chain and can cause cracks in the chain. Minimum cutte...
Page 20 - Files and how to work with them; Chain typ
20 All cutters must be sharpened to the same angle, 30°. Different angles result in a roughly, irregularly running chain, increase wear and tear and cause chain beakage. The 85° front rake of the cutter results from the cut depth of the round fi le. If the proper fi le is used in the right manner, t...
Page 21 - thoroughly
21 1 2 4 5 6 3 Cleaning the guide bar, lubricating the sprocket nose CAUTION: Protective gloves must be worn. Regularly inspect the bearing surfaces of the guide bar for damage, and clean them with a suitable tool. If the saw is used intensively it will be necessary to lubricate the return sprocket ...
Page 22 - Replacing the suction head; Cleaning the air
22 12 7 8 9 10 11 Replacing the suction head The felt fi lter ( 12 ) of the suction head can become clogged. It is recommended to replace the suction head once every three months in order to ensure unimpeded fuel fl ow to the carburetor. To remove the suction head for replacement, pull it out throug...
Page 23 - Replacing the spark plug; Electrode gap; Replacing the starter cable
23 2 3 6 7 8 4 5 12 10 9 11 12 1 Replacing the spark plug CAUTION: Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work. A hot engine can cause burns. Wear protective gloves! The spark plug must be replaced in cas...
Page 24 - Cleaning the cylinder space; Ensure correct mounting position.; Replacing the return spring unit
24 13 Cleaning the muf fl er CAUTION: If the engine is hot there is a risk of burning. Wear protective gloves. Remove the sprocket guard (see ”PUTTING INTO OPERATI-ON” Fig. B). Remove deposits of carbon from the exhaust outlets ( 13 ) of the muf fl er. D E Cleaning the cylinder space Remove the spro...
Page 25 - Maintenance and repair
25 Instructions for periodic maintenance To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the ...
Page 26 - Trouble shooting; Malfunction System
26 Spare parts Reliable long-term operation, as well as the safety of your chain saw, depend among other things on the quality of the spare parts used. Use only original MAKITA parts, marked Only original spare parts and accessories guarantee the highest quality in material, dimensions, functioning ...
Page 27 - Extract from the spare parts list
27 Extract from the spare parts list Use only original MAKITA parts. For repairs and replacement of other parts, see your MAKITA service centre. DCS3410TH Identi fi cation plate Indicate when ordering spare parts Serial numberYear of manufacture 15 17 16 18 19 20 21 5, 6, 7 8, 9 6, 7 11 10 3 4 2 12 ...
