Makita BDF460 - Manual - manualsarea.com

Page 2 - SPECIFICATIONS; GENERAL SAFETY RULES; Read and understand all instructions.; Failure to follow all

2 SPECIFICATIONS • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA003-1 (FOR All BATTERY OPERATED TOOLS) WARNING: Read and understand all instructions. Failure to follow all instructions listed bel...

Page 3 - SAVE THESE INSTRUCTIONS; Work Area

3 SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite acci-dents. 2. Do not operate power tools in explosiveatmospheres, such as in the presence offlammable liquids, gases, or dust. Power tools create sparks which may ignite the dustor...

Page 4 - SERVICE; SPECIFIC SAFETY RULES

4 18. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely tobind and are easier to control. 19. Check for misalignment or binding of moving parts, breakage of parts, and anyother condition that may affect the tool’soperation...

Page 10 - Tips for maintaining maximum battery life

10 • Check the sound of cooling fan, vent on the charger andbattery, which can be sometime clogged with dust. • The cooling system is in order although no sound ofcooling fan comes out, if the yellow warning light will notflash. • Always keep clean the vent on charger and battery forcooling. • The p...

Page 13 - ASSEMBLY; Installing or removing driver bit or drill bit

13 ASSEMBLY CAUTION: • Always be sure that the tool is switched off and thebattery cartridge is removed before carrying out anywork on the tool. Installing side grip (auxiliary handle) CAUTION: • Always be sure that the side grip is installed securelybefore operation. Always use the side grip to ens...

Page 14 - Adjustable depth rod; OPERATION; Screwdriving operation

14 Adjustable depth rod The adjustable depth rod is used to drill holes of uniformdepth. Loosen the clamp screw, set to desired position, thentighten the clamp screw. OPERATION CAUTION: • Always insert the battery cartridge all the way until itlocks in place. If you can see the red part on the upper...

Page 15 - Drilling operation; Drilling in wood

15 • If the tool is operated continuously until the batterycartridge has discharged, allow the tool to rest for 15minutes before proceeding with a fresh battery. Drilling operation First, turn the adjusting ring so that the pointer points to the marking. Then proceed as follows. Drilling in wood Whe...

Page 16 - MAINTENANCE; Replacing carbon brushes

16 • Always secure small workpieces in a vise or similar hold-down device. • If the tool is operated continuously until the batterycartridge has discharged, allow the tool to rest for 15minutes before proceeding with a fresh battery. MAINTENANCE CAUTION: • Always be sure that the tool is switched of...

Page 17 - Recycling the Battery; ACCESSORIES

17 EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it.The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. a) Take the battery to your nearest Makita Factory Ser-vice Center or b) Take the battery to ...

Page 18 - Memo

Page 22 - Your answers to the following questions are appreciated.; Certificate of Warranty

22 Your answers to the following questions are appreciated. Date Purchased Model No. Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Year 20 Under 19 20-29 30-39 40-49 Over 50 Paste Paste Paste Paste Paste Paste Paste Paste P aste P aste P aste P a...

Page 23 - Factory Service Centres; CUSTOMER RECORD

23 Factory Service Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “tools” or con-tact our customer service department (Tel) 1-800-263-3734 When you need service... • Explain the problem in a letter • Enclose the letter with the tool • Pac...

Page 24 - Warranty Policy; MAKITA LIMITED ONE YEAR WARRANTY; Makita Corporation

Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects fromworkmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop duringthis one year period, return the COMPLE...

Makita BDF460 - Manual

Table of Contents:

Summary

Other Makita Models