LXE E-EQ-VX3XDKRG-C-ARC - Manual

Table of Contents Powered Vehicle Mounting 1 Overview 1 Quick Start - Powered Vehicle Mounted Assembly 1 Briefly .... 1 Installation 2 Components 3 RAM Mounting Assembly Components 3 Procedure 3 Torque Measurement 4 Step 1 – Mount Vehicle RAM Clamp Mount 4 Step 2 – Attach RAM Mount Ball to the VX3X ...

Powered Vehicle Mounting Overview Vehicle mounted brackets are specifically designed for vehicle mount applications. The vehicle mounted assembly restrainsthe VX3X and isolates it from shock and vibration.Overhead, dash and roof support pillar mounting is via a RAM Mount accessory which includes all...

Installation Installation Refer to the VX3X Reference Guide when connecting Input/Output devices to the VX3X endcap after the VX3X is mounted to a vehicle. Caution : This device is intended to transmit RF energy. For protection against RF exposure to humans and inaccordance with FCC rules and Indust...

Components Components RAM Mounting Assembly Components The RAM mounting assembly consists of the following parts: 1. VX3X RAM ball (included with VX3X) 2. RAM arm, size C 3. RAM clamp mount includes: l Upper Clamp Piece with Ball l Lower Clamp Piece l Bolts (2 each) l Nylon locking nuts (2 each) 4. ...

Torque Measurement Torque Measurement You will need a torquing tool capable of torquing to 20 inch pounds (1.10 N/m). Torque all screws and bolts according to thefollowing table: For these nuts… Torque to 10-32 lock nuts 17 - 20 in/lb (0-95 - 1.10 N/m) Step 1 – Mount Vehicle RAM Clamp Mount Componen...

Step 3 – Attach VX3X Assembly to RAM Mount Step 3 – Attach VX3X Assembly to RAM Mount Slip the RAM arm over the ball on the vehicle RAM clamp mount.Insert the ball of the RAM mount bracket into the RAM arm.Adjust the VX3X to the desired position and tighten the knob on the RAM arm using the supplied...

Vehicle 12-80VDC Power Connection Vehicle 12-80VDC Power Connection Caution: For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. Thisfused circuit requires a two Amp maximum time delay (slow blow) high interrupting rating fuse. If the supplyco...

External Power Supply, Optional External Power Supply, Optional Note: The LXE-approved AC Power Supply and Adapter Cable are only intended for use in a 25ºC (77ºF) maximumambient temperature environment. In North America, this unit is intended for use with a UL Listed ITE power supply with output ra...

Connect Power Cable Connect Power Cable 1. Connect the power cable to vehicle power (See Vehicle 12-80VDC Power Connection .) 2. The plug and receptacle are keyed and care must be used when connecting the cables. Tighten the nut of the plug clock- wise until tight. 3. Secure the cable with a strain ...

Strain Relief Cable Clamps Strain Relief Cable Clamps Equipment Required : Phillips screwdriver (not supplied by LXE) There are two strain relief cable clamps secured to the VX3X endcap.Use the strain relief clamps to secure audio, power, and I/O cables attached to the VX3X. 1. Remove the strain rel...

Connect Antenna Connect Antenna If the VX3X has the optional remote mount external antenna on the endcap, see Vehicle Remote Mount Antenna for instruction. If the VX3X has an internal antenna (has an audio connector on the endcap and no antenna connector), the internal antennawas connected when the ...

Typical Installation Typical Installation 1. Antenna 2. Mounting Plate 3. Vehicle Safety Cage 4. Coaxial Cable 5. Vehicle Mounted VX3X E-EQ-VX3XDKRG-C-ARC [ 13  ] VX3X Cradle Reference Guide

Components and Mounting Diagram Components and Mounting Diagram 1. Nut 2. Lock Washer 3. Rubber Washer 4. Mounting Plate 5. To Antenna 6. To VX3X Antenna Connector 7. Antenna E-EQ-VX3XDKRG-C-ARC [ 14  ] VX3X Cradle Reference Guide

Mounting Instruction Mounting Instruction 1. Attach and secure the mounting plate to the highest point on the safety cage, following these precautions: l The plate must be mounted so the antenna is not damaged while the vehicle or any of its parts are mov-ing. l The mounting plate must be parallel t...