Lowrance M68I - Manual
Lowrance M68I – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 5 – Communications Port Activation; either; ENT; Enable NMEA command on the unit's Main Menu; Communications Port Configuration; Menus for changing Com Port settings.
- Page 6 – Configure NMEA; NMEA Sentences selection menu.
- Page 7 – Compatibility With Various VHF Radios
- Page 8 – Correction; To enter the IceMachine mode:; EXIT; This addendum supplements the manual
1
Pub. 988-0152-061
Addendum I
Additional Instructions for
Lowrance M68i S/Map
Your sonar/GPS unit, the M68i, functions exactly like the M68 de-
scribed in the manual provided (part 988-
0152-031
). In addition, the
M68i contains a communications port for NMEA 0183 output. The in-
structions for connecting data cables and setting up the communica-
tions port appear in this addendum. The back page also includes a cor-
rection note for an error in the M68 manual.
NMEA 0183 Cable Connections
NMEA is a standard communications format for marine electronic
equipment. The M68i can send information to any device that receives
NMEA 0183 data. This allows the unit to work with VHF marine radios
equipped with the Digital Selective Calling (DSC) distress call feature.
To send NMEA 0183 data, the M68i has one NMEA 0183 version 2.0
communication port. The com port can be used to send NMEA format-
ted data such as your current position.
The provided M68i data cable plugs into the accessory socket on the
right side of the back of your unit's case. This socket can connect
either
an accessory such as a speed or temperature sensor
or
a NMEA 0183
data cable. The data cable ends in two wires that connect to your VHF
radio or other NMEA device. The M68i uses the yellow wire to transmit
and the black shield wire for signal ground.
NOTE:
Some VHF radios, such as the popular Uniden
brand, have input lev-
els which require use of an additional diode and resistor built into the
M68i data cable. This is
Wiring Diagram
A
, which is described on
page 2. The majority of the DSC radios will work with the resistor and
diode as provided by Lowrance Electronics.
A few other radio brands (and other electronic devices) that meet the
NMEA 0183 standard won't need these adapters
and you will have to
remove the resistor and diode to make those work.
This is
Wiring Dia-
gram
B
, which is described on page 3.
Consult your other device's owner’s manual, then read through
all
of
the following instructions before you begin. Use the installation dia-
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
5 When the data cable is connected to your VHF radio, all you have to dois plug it into the sonar/GPS unit. Attach the data cable's plug to theaccessory socket on the right side of the back of your unit's case. Communications Port Activation Now that you have your devices connected, here's how to ma...
6 If you need additional assistance in configuring the unit to communicatewith another device, consult the factory; customer service phone num-bers are in the back of the unit's manual. To set Com Port Configuration: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT . 2. Press ↓ to C OMMUNICATIONS P ...
7 A menu appears showing the prefixes of the available NMEA sentences.A check mark next to a prefix means the prefix is in use. Use ↑ ↓ → ← to select a prefix, then press ENT to turn off the prefix. (Press ENT again to check the box and turn a prefix on.) NOTE: The names of the NMEA sentences are ab...
