LOREX WA-410 - Manual

Planning for Installation 4 The security system is designed to be as flexible as possible in order to meet your present needs, and also to adapt as your needs change. For the reason, we recommend that you read and consider the following information and plan your system before installing these device...

5 Connecting the Telephone Line To connect the Main Console to the telephone line, Please follow these steps: 1. Locate the two phone jacks at the top of the main console. These phone jacks are marked “ Phone “ and “ Line “. 2. Connect one end of the telephone cord that came with the system into the...

Operation – Main Console The Main Console is the heart of the security system. It monitors the sensors and responds according to how it is programmed, whenever a sensor is activated. The illustration shown for the Main Console may look complex at first, however, most procedures are straightforward a...

13. Armed LED : When the light is ‘on’, the system is armed; When the light is ‘off’, the system is disarmed. 14. LCD Panel : Displays messages 15. Speaker : Sounds alarm and plays back messages 16. Antenna : Used for wireless reception 17. Output Jack : Connects to the external siren 18. Phone Jack...

be cleared. Press 3 to go into the clear mode. Clear Sensor 1 – Single 2 - All Press 1 , and key-in the sequence learning order number. Press ENTER , to clear the sensor. Clear Sensor 1 – Single Num: xx Clear Sensor Clear OK Num : xx Press 2 , It will display the words “Are you sure ? ”. Press ENTER...

z If the password is correct, the main console will emit a long beep sound. (LCD display shown below). Access Granted Master Mode : MASTER A-AWAY H-HOME Now the system will select the arm mode and set the system in either Away arm/Home Arm mode (see below): A - AWAY : Press the AWAY button to set th...

is answered, it will playback the message 2 times Medical help - It will automatically dial Preset 6 → Preset 1 → Preset 2 → Preset3, phone numbers for 3 cycles (6, 1, 2, 3). When the telephone is answered, it will playback the message 2 times LCD “MSG” : Message indicating on LCD This system will l...

Remote Control Handset The key chain Remote Control Handset is a convenient way to arm (Home / Away mode) or disarm this system. Before using this device, please program it into the main console via the sequence programming menu. 1. TRANSMIT LED : The LED will light when the device is transmitting 2...

• Press the PANIC button, to activate the “PANIC” function. The activation of the “PANIC” function will immediately trigger the alarm and auto dialer. 63 REMOTE SENSOR 01 Panic PIR Motion Detector The PIR Motion Detector is designed to detect the movement of objects in a room or hallway. The effecti...

4. BATTERY : Remove the Battery cover and insert one 9V alkaline battery. 5. ARM & HOLDER : For mounting on the wall. 6. BATTERY COVER Replace the Battery z When the sensor sends a low battery message to main console, remove the old battery and replace it with a fresh alkaline battery. The LCD i...

Before installing the sensor, consider the following points: z Mount the sensor two meters (6-1/2’) high for best coverage. z Mount the sensor with a 14 degree downward incline angle against the wall for optimum range. To install the PIR Motion Sensor, please follow these steps : z Take out the scre...

Door/Window Detector (for DC 12V battery) 20 Change the Battery When the sensor sends a low battery message to the main console, remove the old battery and replace it with a fresh alkaline battery. The low battery message on the LCD is shown below Button function 1. Magnet. 2. Transmit LED : When th...

1. The LED on the sensor will flash once when the sensor is triggered. 2. There cannot be a gap greater than 1/4 inch (5 mm) between the magnet sensor and the magnet, otherwise, the sensor will not work properly. Enter the installer password and press the “1” button to activate the “Sequence Program...

INSTALLING POSITION REFERENCE FOR DOOR/WINDOW DETECTOR Mini Siren The siren is an effective deterrent to intruders. Choose a location inside your home where the siren is not plainly visible, but can be heard throughout the house. It is important to install the siren where the cable can be hidden, an...

1. Plug the wire into the control panel OUTPUT JACK 2. Cord length – 8 meters. 3. Loudness output – 110 db. 4. Dimensions – 3.7 x 4.5 x 2 (cm) 5. Weight – 120g (including the cord) Summary of Program – Main Console Use the following form to record your programming choices for future reference. 23

Item Descriptions Install Code Master Code Exit Time Alarm Time Entry Time Auto-dialing Mode Preset Telephone No. for Auto-dialing : No. 1 Name Tel. No. No. 2 Name Tel. No. No. 3 Name Tel. No. No. 4 (Burglary Emergency) Name Tel. No. No. 5 (Fire Emergency) Name Tel. No. No. 6 (Help Emergency) Name T...

Learning Number Place of Installation Zone Label Learning Number Place of Installation Zone Label 05 2F-xx room Window 1 Learning Number Place of Installation Zone Label Learning Number Place of Installation Zone Label 01 33 02 34 03 35 04 36 05 37 06 38 07 39 08 40 09 41 10 42 11 43 12 44 13 45 14 ...

Items Specifications Frequency - 303Mhz or 433Mhz Power Source - AC120V, DC 12V Power Consumption - 70mA (idle), 170mA (activated) Back-up Battery (Optional) - Approximate 7 hours ( NO AC adaptor) Temperature Range - 0°C 40°C RF Range - 100 feet in open air space Security Code - Hopping code Alarm A...

It’s all on the web Product Information User Manuals Quick Start Guides Specification Sheets Software Upgrades Firmware Upgrades Lorex Technology I nc. VISIT wwwlorexcctv.com www.lorexcctv.com