Life fitness PL06 - Manual
Life fitness PL06 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Smith Machine PL06 Unpacking & Assembly Instructions; UNPACKING; DO NOT REMOVE THE FOUR HOLLOW TUBE BUMPERS (SHOWN IN
- Page 3 – the bottom cross brace board as shown in Unpacking Figure 3.; Unpacking Figure 3. Remove the front and back brace lag screws.
- Page 4 – THE STEP BELOW REQUIRES THREE PEOPLE. SOMEONE NEEDS TO; Unpacking Figure 4. Removing the upper shipping board.
- Page 5 – Remove the bottom shipping cross brace; (with Person 1 holding the right side and; Unpacking Figure 5. Shipping cross brace.; W ITH PERSON 1 HOLDING THE RIGHT; Unpacking Figure 6. Remove the bottom shipping boards.
- Page 6 – Unpacking Figure 7. Smith Machine PL06 main components.; side
- Page 7 – ASSEMBLY; W ith Person 2 holding the left side and Person 3 holding; Assembly Figure 1. Attach the front brace.; The two lower bolts on the front brace will NOT have washers or
- Page 8 – Insert the back brace with the warning label facing inward; Tighten the bolts on the front brace.; Tighten the four bolts on the front brace using a; Put end caps on all the bolt heads and the nuts.; Snap the end caps (part number C in
- Page 9 – Assembly Figure 5. Remove the right bar carriage.; Have one person take the bar carriage and pull it down; Insert the bar into the right side carriage.; Swing the carriage out by pulling down on
- Page 10 – Insert the bar into the left side carriage.; Repeat Steps 5 and 6 above for the left side; Assembly Figure 7. Remove the bar from the hook plate.; Repeat this step for the other side of the carriage.
- Page 11 – Using a 5/32” hex head driver and 3/8” combination; Assembly Figure 9. Carriage bolt tightening pattern.
- Page 12 – HARDWARE; Hardware Figure 1. Back and Front Brace Parts.
- Page 13 – PARTS ORDER LIST; Use the list below if you need to order parts from Life Fitness.; Description; Main components; Bar; Cable jam nut; Carriage hardware; Pillow block sliders; Bar spacers; Plastic bar spacers
M051-K50-B101
1
SMITH MACHINE PL06
UNPACKING & ASSEMBLY INSTRUCTIONS
The Smith Machine PL06 comes disassembled. Follow the steps below to assemble it.
WARNING:
ASSEMBLING THE SMITH MACHINE PL06 REQUIRES AT LEAST THREE
PEOPLE. COMPONENTS OF THIS MACHINE ARE LARGE AND HEAVY. USE
CAUTION WHEN ASSEMBLING THIS MACHINE.
MATERIALS AND TOOLS REQUIRED FOR UNPACKING AND ASSEMBLY
5/32” Hex
head wrench
1/2”, & 9/16”
Socket
wrench
3/8”, 7/8” &
9/16”
Combination
wrench
Rubber mallet
You will also need a ladder.
ASSEMBLY TIME
Three people can accomplish this assembly in approximately 1 hour.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Smith Machine PL06 Unpacking & Assembly Instructions 2 UNPACKING Follow the steps below when unpacking the components of the crate. Keep in mind thatthe sides of the PL06 are large and heavy. This machine requires three people to uncrate . 1. Remove the shipping wrapper. NOTE: DO NOT REMOVE THE ...
Smith Machine PL06 Unpacking & Assembly Instructions 3 Unpacking Figure 2. Remove the bar. C. Remove the back brace and front brace using a 9/16” socket. They are lagged to the bottom cross brace board as shown in Unpacking Figure 3. Unpacking Figure 3. Remove the front and back brace lag screws...
Smith Machine PL06 Unpacking & Assembly Instructions 4 1 2 3 Person 1- Holds right sidePerson 2- Holds left sidePerson 3- Moves around and assembles At this stage, three people are required to uncrate the PL06 because the sides are veryheavy and not stable until they are bolted to the front and ...
