Life fitness OHDHR - Manual

Page 2 - PARTS LIST; Tools Required for Assembly

PARTS LIST PART # LEA 7664801 LEA 7665001 LEA 7665101 LEA 7584901 LEA 7665501 LEA 7586601 LEA 7622401 LEA 7663901 LEA 7584401 LEA 7584501 LEA 7587501 LEA 7587901 LEA 7587801 LEA 7605901 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 QTY 1 1 1 2 1 2 1 1 1 1 10 1 1 1 KEY 15 16 17 18 19 20 21 22 23 24 25 26 PART...

Page 4 - FIGURE 1

STEP 1: FIGURE 1 4 • LOOSELY assemble the REAR UPRIGHT (4) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOLTS (25), two 1/2” PLASITC DOME WASHERS (21), two 1/2” INT TOOTH LOCK WASHERS (19) and two 1/2” LOCK NUTS (22) as shown in FIGURE 1. 22 4 4 25 1/2 X 4-1/4” 2 19 1 21 • LOOSELY assemble th...

Page 5 - FIGURE 2

5 STEP 2: FIGURE 2 • LOOSELY assemble the BOTTOM UPRIGHT SUPPORT (15) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/4” BOLTS (25), four 1/2” PLASITC DOME WASHERS (21), four 1/2” INT TOOTH LOCK WASHERS (19) and four1/2” LOCK NUTS (22) as shown inFIGURE 2. 4 25 1/2 X 4-1/4” 21 4 15 19 22 Use this set ...

Page 6 - FIGURE 3

6 STEP 3: FIGURE 3 • LOOSELY assemble the LEFT UPRIGHT SUPPORT (3) to the LEFT UPRIGHT BASE (1) and REAR UPRIGHT (4) using four 1/2 X 4-1/4” BOLTS (25), four 1/2” PLASITC DOME WASHERS (21), four 1/2” INT TOOTH LOCK WASHERS (19) and four 1/2” LOCKNUTS (22) as shown in FIGURE 3. 22 4 4 25 1/2 X 4-1/4”...

Page 7 - FIGURE 4

7 STEP 4: FIGURE 4 • LOOSELY assemble the PULL-UP SUPPORT (8) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/4” BOLTS (25), four 1/2” PLASTIC DOME WASHERS (21), four 1/2” INT TOOTH LOCK WASHERS (19) and four 1/2” LOCK NUTS (22) as shown in FIGURE 4. 8 19 21 22 1/2 X 4-1/4” 25 4 4

Page 8 - FIGURE 5

8 STEP 5: FIGURE 5 • LOOSELY assemble the WEIGHT HORN UPRIGHTS (6) to the LEFT & RIGHT UPRIGHT BASE (1 & 2) and REAR UPRIGHTS (4) using eight 1/2 X 4-1/4” BOLTS (25), eight 1/2” PLASTIC DOME WASHERS (21), eight 1/2” INT TOOTH LOCK WASHERS (19)and eight 1/2” LOCK NUTS (22) as shown in FIGURE ...

Page 9 - FIGURE 6; Securely tighten all loose frame connections made to this point.; TIGHTEN

9 STEP 6: FIGURE 6 • Securely tighten all loose frame connections made to this point. TIGHTEN BOTH SIDES! TIGHTEN BOTH SIDES!

Page 10 - FIGURE 7; DETAIL 7

10 STEP 7: FIGURE 7 • LOOSELY assemble one RIGHT & one LEFT ADJUSTMENT RACK (9 & 10) to the REAR UPRIGHTS (4) as shown, using eight 3/8 X 3-3/4” FLAT HEAD BOLTS (17), eight 3/8” INT TOOTH LOCK WASHERS (20) and eight 3/8” LOCK NUTS (23). See FIG-URE 7. 23 3/8 X 3-3/4” 17 20 9 10 4 4 13 12 • B...

Page 11 - FIGURE 8

11 STEP 8: FIGURE 8 • SECURELY assemble the ten WEIGHT HORNS (11) to the WEIGHT HORN UPRIGHTS (6) using twenty 1/2 X 4-1/4” BOLTS (25), twenty 1/2” INT TOOTH LOCK WASHERS (19), twenty 1/2” PLASTIC DOME WASHERS (21) and twenty 1/2” LOCK NUTS (22) asshown in FIGURE 8. 1/2 X 4-1/4” 25 19 11 6 6 21 22

Page 12 - FIGURE 9

12 STEP 9: FIGURE 9 • Assemble two SWIVEL SPOTTERS (24) to the BOTTOM UPRIGHT SUPPORT (15) as shown using four 1/2 X 1-1/2” BOLTS (16), four 1/2” INT TOOTH LOCK WASHERS (19), four 1/2” FLAT WASHERS (18) and four 1/2” LOCK NUTS (22). See FIGURE 9. (NOTE: Tighten connection SECURELY then back nut off ...

Page 14 - equipment, call your local Hammer Strength distributor .

14 STEP 11: FIGURE 11 7 9 10 14 Thank you for purchasing the OLYMPIC HEAVY DUTY HALF RACK. If unsure of proper use of equipment, call your local Hammer Strength distributor . SERIAL NUMBER • Insert the LEFT BAR CATCH (7) into the desired slots of the LEFT ADJUSTMENT RACK (10), and allow it to drop d...

Page 15 - PREVENTATIVE MAINTENANCE TIPS; Consult your physician before beginning any exercise program.; WARRANTY INFORMATION

Clean: • Upholstery with mild soap and water.• Guide rods with a cotton cloth.• Hand grips with mild soap and water.• Frame damage can be repaired with touch-up paint can be purchased from your Hammer Strength customer service representative. Inspect: • Cables for wear or damage and proper tension (...

Life fitness OHDHR - Manual

Table of Contents:

Summary

Other Life fitness Models