Life fitness 8115 - Manual - manualsarea.com

Page 2 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH; Consult your physician before beginning any exercise program.

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8115 FLAT & INCLINE BENCH. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on aflat, level surface to assure its proper function. 2 NO...

Page 3 - PARTS LIST; FIGURE 1

3 PARTS LIST PART # 6651703 6700503 6712803 6697203 6624202 6624302 6651602 6780001 6780301 3202106 3202107 3102917 3102910 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 QTY 1 1 1 1 1 1 2 1 1 1 1 2 2 KEY 14 15 16 17 18 19 20 21 22 23 24 25 PART # 3202101 3102901 3102502 3102501 3102801 3102804 6406401 6619301 6...

Page 4 - FIGURE 2

STEP 2: FIGURE 2 • SECURELY assemble the 3/8” SPRING PIN (23) to the ADJUSTABLE SLEEVE (3) as shown in FIGURE 2. 4 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Pull back the 3/8” SPRING PIN (23) on the ADJUSTABLE SLEEVE (3) and slide it over the end of the BENCH FRAME (2) as shown in FIGURE 2. Slide the ...

Page 5 - FIGURE 3

STEP 3: FIGURE 3 5 • SECURELY assemble the REAR UPRIGHT (1) to the BENCH FRAME (2) using two 1/2 X 3” BOLTS (13), four 1/2” WASHERS (16), and two 1/2” LOCK NUTS (18) as shown in FIGURE 3. 1/2 X 4” 12 13 1/2 X 3” • SECURELY assemble the BASE TUBE (4) to the BENCH FRAME (2) using two 1/2 X 4” BOLTS (1...

Page 6 - FIGURE 4

STEP 4: FIGURE 4 6 • Assemble the LEFT & RIGHT BACK PAD ANGLES (5 & 6) and two HINGE TABS (20) to the BENCH FRAME (2) using one 1/2 X 9-1/2” BOLT (10) and one 1/2” LOW HEIGHT LOCK NUT (19). (NOTE: Tighten connection enough to remove play yet allowing the parts to rotate freely.) See FIGURE 4...

Page 7 - FIGURE 5

7 STEP 5: FIGURE 5 • Assemble the LEFT & RIGHT BACK PAD ANGLES (5 & 6) and two HINGE TABS (20) to the BENCH FRAME (2) using one 1/2 X 9-1/2” BOLT (10) and one 1/2” LOW HEIGHT LOCK NUT (19). (NOTE: Tighten connection enough to remove play yet allowing the parts to rotate freely.) See FIGURE 4...

Page 8 - FIGURE 6

8 FIGURE 6 STEP 6: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the BACK PAD (9) to the LEFT & RIGHT BACK PAD ANGLES (5 & 6) using four 3/8 X 1-1/4” BOLTS (15) and four 3/8” WASHERS (17) as shown in FIGURE 6. 3/8 X 1-1/4” 15 9 5 6 17

Page 9 - FIGURE 7

STEP 7: 9 FIGURE 7 • SECURELY assemble the SEAT PAD (8) to the HINGE TABS (20) using two 3/8 X 1-1/4” BOLTS (15) and two 3/8” WASHERS (17) as shown in FIGURE 7. 3/8 X 1-1/4” 15 17 8 20 Thank you for purchasing the LifeFitness 8115 FLAT & INCLINE BENCH. If unsure of proper use of equipment, call ...

Life fitness 8115 - Manual

Table of Contents:

Summary

Other Life fitness Models