Page 2 - On Safety; The appliance coupler is used as the disconnect device.; Important Precautions
1 This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, ...
Page 3 - On Installation; Avoid high temperatures and humidity.
2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a s...
Page 4 - On Cleaning; screen because over-spraying may cause electrical shock.; On Repacking; your local authority.
Important Precautions 3 On Cleaning Unplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub...
Page 5 - Accessories; IMPORTANT
4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer. OWNER'S MANUAL/Cards Power Cord (Depending on the country) DVI-D Signal Cable (Dual) IMPORTANT This accessories may look different...
Page 6 - Connecting the Display; Connecting and Disassembling the stand; Place the monitor face down on the soft cloth.; into the; Stand Body; in the correct direction.; Stand Base
5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices is turned off. Connecting and Disassembling the stand 1. Place the monitor face down on the soft cloth. 2. Assemble the Stand Base into the Stand Body in the c...
Page 8 - Positioning your display; After installation, adjust the angle as shown below.; -5 ̊ to 15 ̊; ERGONOMIC
7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices is turned off. Positioning your display After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum co...
Page 9 - system, and other attached devices is turned off.; Connecting with the PC/AV equipment; NOTE; Press the Power Button ( ) on the front panel to turn the power on.
8 Connecting the Display A Connect DVI-D (Digital signal) CableConnect HDMI Cable (HDMI1, HDMI2) 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten ...
Page 10 - Control Panel Functions; Front Panel Controls; MENU Button; MENU button; Button; ARC
9 Control Panel Functions Front Panel Controls MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds. The me...
Page 11 - SET Button; You can select; GAME; or; MUSIC; light will be turned off.; Power Button; Buttons
10 Control Panel Functions Use this button to enter a selection in the On Screen Display. SET Button You can select GAME , MOVIE or MUSIC by using this button and the LED lightshape will change according to eachmode. When you select OFF , the LED light will be turned off. TRU-LIGHTButton Use this bu...
Page 12 - Screen Adjustment; On Screen Display (OSD) Control Adjustment
11 Screen Adjustment Making adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use of thecontrols. The following section is an outline of the availablead...
Page 13 - The order of icons may differ depending on the model (12 to 19).; SETUP
12 On Screen Display (OSD) Control Adjustment NOTE The order of icons may differ depending on the model (12 to 19). LANGUAGEVOLUME OVERSCAN RTC LIGHTING LEVELPOWER INDICATORFACTORY RESET Additional settings SETUP SHARPNESS To adjust the clearness of the screen. TRACKING PRESET (sRGB / 6500K / 9300K)...
Page 14 - On Screen Display(OSD) Selection and Adjustment; ON; Turn off SRS function.
13 On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you press the button on the frontof the monitor. Main menu Sub menu Description SRSTRUSURROUNDHD ON Turn on SRS function, offer 3D surroundfor live sound effect. OFF Turn off SRS function. is a trademark of SRS Labs, ...
Page 16 - Press the MENU Button, then the main menu of the OSD appears.; Menu Name
15 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting anitem using the OSD system. Listed below are the icons, icon names,and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appear...
Page 17 - PICTURE; To adjust the brightness of the screen.
16 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE MENU : Exit : Decrease : Increase SET : Select another sub-menu BRIGHTNESS CONTRAST GAMMA BLACK LEVEL To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value: -50 ...
Page 18 - COLOR
17 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PRESET RED GREEN BLUE HUE SATURATION COLOR RESET • sRGB : Set the screen color to fit the sRGB standard colorspecification. • 6500K : Slightly reddish white. • 9300K : Slightly bluish white. Set your own red color leve...
Page 19 - TRACKING; SHARPNESS; To adjust the clearness of the screen.
18 On Screen Display(OSD) Selection and Adjustment TRACKING Main menu Sub menu Description MENU : Exit : Decrease : Increase SET : Select another sub-menu SHARPNESS To adjust the clearness of the screen. DVI-D, HDMI input
Page 20 - LANGUAGE; HDMI input
19 On Screen Display(OSD) Selection and Adjustment Press the , buttons to reset immediately. SETUP MENU : Exit : Decrease : Increase SET : Select another sub-menu Main menu Sub menu Description To choose the language in which the controlnames are displayed. To adjust the volume of headphone/Earphone...
Page 21 - Troubleshooting; Check the following before calling for service.; No image appears
20 Troubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? • You can secure the current control settings, so that they cannot be inadvertently changed.You can unlock the OSD controls at any timeby push...
Page 22 - The screen color is
21 Display image is incorrect Do you see an "Unrecognized monitor, Plug&Play (VESA DDC)monitor found" message? The Audio function is not working IMPORTANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the vide...
Page 23 - Specifications
22 Specifications 58.4 cm (23.0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size: 58.4 cm0.266 mm x 0.266 mm (Pixel Pitch) Horizontal Freq. Digital: 30 kHz to 141 kHzHDMI: 30 kHz to 83 kHz Vertical Freq. Digital: 56 Hz to 120 HzHDMI: 56 Hz to 61 Hz Input Form Digital (...
Page 24 - Indicator; LED Color; HDMI Vedio INPUT
23 Specifications Indicator On Mode Sleep Mode Off Mode Blue Blue Blinking Off LED Color MODE Preset Modes (Resolution) - DVI-D(Digital) INPUT Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 123456789 10111213 *14 **15**16**17 640 x 350720 x 400640 x 480640 x 480800 x 600800 x ...
Page 25 - Installing the Wall mount plate
24 Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plateor the interchange device. 1. Place the monitor face down on the soft cloth. 2. To disconnect the Stand Base from the Stand Body, unfold the screw handle andturn it to the left. 3. Pull out the Stand ...
Page 26 - Install the Wall mount plate.
Installing the Wall mount plate 25 4 . Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for more details,which is provided when Wall mount plate ispurchased. Kensingt...
