Page 2 - On Safety; The appliance coupler is used as the disconnect device.; Do not Open the Display:; Important Precautions
A1 This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation,...
Page 3 - On Installation; Avoid high temperatures and humidity.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a swi...
Page 4 - On Cleaning; screen because over-spraying may cause electrical shock.; On Repacking; your local authority.
A3 Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scru...
Page 5 - Accessories; Please make sure the following items are included with your; NOTE
A4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Owner's Manual/Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product befor...
Page 6 - Basic Adjustments of the Stand; How to adjust the angle of the panel; Basic Adjustment
Basic Adjustments of the Stand A5 1. Adjust the angle of the panel as follows. How to adjust the angle of the panel Tilt Range : T1710B : 15˚ to 66˚ T1910B : 15˚ to 68˚ 15˚ 66˚(68˚) The state which the stand locking handle is released The state which the stand locking handle is locked Do not push th...
Page 7 - Using the Computer; Connecting the Display
A6 Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch mapform to . 1 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. 2 Connecting the Dis...
Page 8 - To Use Touch Screen; Install the Driver CD provided.; USB cable for the touch screen
Connecting the Display A7 To Use Touch Screen Install the Driver CD provided. 1) Insert Touch Screen Driver CD into PC CO-ROM.2) After completing the driver installation, connect the USB cable for the touch screen. 3) Please refer to the Touch Screen CD provided separately for detail installations. ...
Page 9 - Control Panel Functions; Front Panel Controls
A8 Control Function Control Panel Functions MENU Button Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, sothat these settings are not inadvertently changed. To lock theOSD settings, press and hold the MEN...
Page 10 - Power Button; Buttons
A9 Control Panel Functions This Indicator lights up as blue when the display isoperating normally(On Mode). If the display is inSleep Mode (Energy Saving), this indicator changesto flicker. Use this button to turn the display on or off. Power Button Power Indicator Use this button to select an icon ...
Page 11 - On Screen Display (OSD) Control Adjustment; Screen Adjustment; To make adjustments in the On Screen Display, follow these steps:
A10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters ofthe display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.The follo...
Page 12 - On Screen Display(OSD) Selection and Adjustment
A11 NOTE The order of icons may differ depending on the model (A11 to A16 ). On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus. (D-sub )
Page 13 - Menu Name; Press the MENU Button, then the main menu of the OSD appears.
A12 Menu Name On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptio...
Page 14 - Main menu; PICTURE
A13 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50On the monitor, high gamma valuesdisplay whitish images and low gammavalues d...
Page 15 - TRACKING
A14 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE SHARPNESS To minimize any vertical bars orstripes visible on the screenbackground.The horizontal screen size will alsochange. To adjust the focus of the display. This item allows you to removeany horizonta...
Page 16 - SETUP
A15 Restore all factory default settings except "LANGUAGE." Press the , buttons to reset immediately. On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description If this does not improve the screen image, restore the factory default settings. If necessary, perform the whit...
Page 17 - NORMAL; USER
A16 On Screen Display(OSD) Selection and Adjustment Icons Menu Name Sub-menu Name Main menu Sub menu Description NORMAL DEMO Select the button at the bottom of the monitor, then the OSD screen will appear. INTERNET : For text images (Word processing etc.) MOVIE : For animation images in videos or mo...
Page 18 - Troubleshooting; Check the following before calling for service.; No image appears
A17 Troubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power on and the power indicator blue orgreen? ● Is...
Page 19 - Display image is incorrect; Important
A18 Troubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, verticalbars or stripes arevisible. ● Any horizontal noise appearing in anyimage or charactersare not clearlyportrayed. • Press the AUTO/SET button to automatically adjust your display image t...
Page 20 - The screen color is; Touch screen does not work.; Did you install the
A19 Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than...
Page 21 - Specifications
A20 Specifications T1710B Display Sync Input Video Input Resolution Plug & Play PowerConsumption Dimensions &Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord NOTE Information in this document is subject to change without notice. 43.27 cm (17.0 inch) Flat Panel Act...
Page 23 - Indicator; LED Color
A22 Specifications Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 123456789 1011 *12 13 640 x 350720 x 400640 x 480640 x 480800 x 600800 x 600832 x 624 1024 x 7681024 x 7681152 x 8701152 x 900 1280 x 10241280 x 1024 31.46931.46831.46937.50037.87946.87549.72548.36360.12368.6816...
Page 24 - Installing the Wall mount plate; Place the monitor with its front facing downward on a soft cloth.
A23 Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate orthe interchange device. 1 . Place the monitor with its front facing downward on a soft cloth. 2 . Separate the head and the stand with the use of a screwdriver.
Page 25 - Kensington Security Slot; Install the Wall mount plate.; Wall Mount pad
A24 Installing the Wall mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for moredetails, which is provided when Wall mount plate ispurchased. Kensington Security Slot Connected to a l...
