Page 3 - Ch1. Service information; Chapter 1. Service information; Before replacing parts; original part before you continue.; Strategy for replacing a hard-disk drive; know that the user is responsible for the loss data; Caution; incorrect drive, data or programs can be overwritten.
2 Ch1. Service information Chapter 1. Service information 1-1. Important service information Strategy for replacing parts (FRU-Field Replaceable Units) Before replacing parts Make sure that latest BIOS and drivers are installed before replacing any parts (FRUs) listed in this Use the following str...
Page 4 - symptoms from the fluid are present after washing.
3 Ch1. Service information 1-2. Safety notices Warning Before the computer is powered-on after part (FRU) replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. ...
Page 6 - Important
5 Ch1. Service information Electrical safety Observe the following rules when working on electrical equipment. Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many...
Page 7 - floor strips and machine frames.
6 Ch1. Service information · Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames. · Observe the special safety precautions when you work with very high voltages. These instructions are in the safety sections of mai...
Page 9 - and the person handling the part are all at the same charge.; useful when handling ESD-sensitive devices.; Note; Grounding requirements
8 Ch1. Service information Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects...
Page 10 - might result in hazardous radiation exposure.; Danger
9 Ch1. Service information 1-4. Laser compliance statement When a CD-ROM drive, DVD drive or the other laser product is installed, note the following : Caution Use of controls or adjustments or performance of procedures other than those specified here in might result in hazardous radiation exposure....
Page 11 - Important Notes; What to do first
10 Ch1. Service information 1-6. Read this first Before you go to the checkout guide, be sure to read this section. Important Notes · Only trained personnel certified by LG should service the computer. · Read the entire FRU removal and replacement page before replacing any FRU. · Use new nylon-coate...
Page 12 - The followings are not covered under warranty :
11 Ch1. Service information The followings are not covered under warranty : · CD panel cracked from the application of excessive force or from being dropped · Scratched (cosmetic) parts · Distortion, deformation, or discoloration of the cosmetic parts · Cracked or broken plastic parts, broken latche...
Page 15 - to prevent a notebook theft; Emergency eject hole
14 Ch2. Locations Rear view (15.4", 17.1") LAN connector USB connector Line in / S/PDIF AC connector Modem connector S-VIDEO connector Express Card eject button 4-in-1 Card slot VGA connector Parallel connector Express Card slot PC Card slot PC Card eject button Left view (15.4", 17....
Page 16 - Ch3. System information; Chapter 3. System information; Specification; FCBGA
15 Ch3. System information Chapter 3. System information Specification - CPU · Dothan 1.6 ~ 2.1 GHz· μ FCBGA - Main Chipset & Graphic · Intel 915GM,ICH6-M· Intel 915PM, ICH6-M, ATI Mobility Radeon X600 VGA Controller - Memory · 2SODIMM – Up to 2GB· DDR2 PC2-3200S/4200S Capable (400/533MHz) - H...
Page 17 - PR CONNECTOR
16 Ch3. System information System Block Diagram (GM) page32 PCIREQ/GNT0 CK-410M Power LED DDR2 page33 5V page47 2.5V page32 page37 AC’97 / AZALIA RJ11/45 CONN CHG VPD EEPROM LAN page41 5V AMP page32 CODEC LCD CONN 3.3V page29 3.3V page 6-12 Int. MIC MIC-IN HUNTER-W page55 USB7 PIO USB2/3 page 2 - ...
Page 20 - The system status indicators show the status of the computer; Wireless activity indicator
19 Ch3. System information Status indicators The system status indicators show the status of the computer 3 1 2 4 5 6 7 1. Caps lock Caps lock indicator lights up when the Caps lock key is pressed.When this indicator lights up, you can type capital letters without pressing the Shift key. 2. Num lo...
Page 22 - a. Backup BIOS and Flash BIOS with new settings
21 Ch3. System information How to update flash ROM in Windows 1. Quit all running programs. 2. Start WINPHLASH.EXE. 3. Select the procedure you want : a. Backup BIOS and Flash BIOS with new settings b. Backup BIOS Only 4. Specify the locations for backup and new BIOS files in BIOS Setting Location...
Page 23 - pressing power button.
22 Ch3. System information 8. After the completion, ‘System BIOS was successfully updated’ appears on the screen, then the computer restarts. 9. After the restart, make sure the system BIOS is updated. 10. If your computer does not restart automatically, turn off your computer and then turn it back ...
Page 24 - BIOS (Basic Input and Output System) Setup
23 Ch3. System information BIOS Setup BIOS (Basic Input and Output System) Setup saves the system configuration in CMOS RAM , and check the configurations during startup. Use the BIOS Setup Utility to change and save the system environment, hardware configurations, power saving mode, etc. · Open t...
Page 25 - Enter
24 Ch3. System information Using the keys The keys used in the BIOS Setup Utility and their functions are described at the bottom. · , + : General Help Display the descriptions of the keys used in the setup utility. · , : Select Item Navigate and select items in the setup utility. The selected ite...
Page 28 - Removable Devices; Exit menu; Exit Saving Changes; Discard change value.; Save Changes
27 Ch3. System information Boot menu Boot menu enables you to set the boot order for the CD-ROM drive, Removable devices Hard drive, and Network boot as shown below. CD-ROM Drive Removable Devices Hard Drive B2 D0 Yukon PXE Exit menu Exit Saving Changes Select Exit Saving Changes to save new set...
Page 29 - Power system checkout
28 Ch4. Symptom-to-part index Chapter 4. Symptom-to-part index The symptom-to-part index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first. Note If replacing a part (FRU) does not solve the problem, put the original part back in the computer. ...
Page 31 - · The Characteristics of the battery pack
30 Ch4. Symptom-to-part index · The Characteristics of the battery pack 1. Self-discharge The battery gradually loses its power over time without ever being used. 2. Periodic full discharge / charge Frequent recharge of the battery pack can reduce the capacity of the battery pack. When this happens,...
Page 32 - Charging will take at least 3 hours.
31 Ch4. Symptom-to-part index · To check the battery pack, do the following : 1. Power off the computer. 2. Remove the battery pack and measure the voltage between battery terminals 1(-) and 5(+). See the following figure : 5(+) 4 3 2 1(-) +0V ~ +12.6V (6 cell) 5 Ground(-) 1 Voltage (V dc) Terminal ...
Page 33 - Numeric error codes; System board; FRU or action, in sequence
32 Ch4. Symptom-to-part index Numeric error codes Replace the backup battery and run BIOS Setup Utilityto reset the time and date. 0250System battery error – System battery is dead 1. DIMM2. System board 0232Extended RAM error - Extended RAM Failedat address line System board 0231Shadow RAM error ...
Page 36 - Error message
35 Ch4. Symptom-to-part index Error message System board. Thermal sensing error. Fan. FAN error. 1. Restore the system configuration to what it was before the computer entered hibernation mode. 2. If memory size has been changed, re-create the hibernation file. Hibernation error. 1. Check that the...
Page 38 - Indeterminate problems
37 Ch4. Symptom-to-part index Indeterminate problems · You are here because the diagnostic tests did not identify which adapter or device failed, wrong devices are installed, a short circuit is suspected, or the system is inoperative. Follow these procedures to isolate the failing FRU (do not isol...
Page 39 - Ch5. Removing and replacing a part; cause electrical short circuits.
38 Ch5. Removing and replacing a part Chapter 5. Removing and replacing a part (FRU) Danger Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Caution Before the computer is powered...
Page 40 - ■ Battery Pack
39 Ch5. Removing and replacing a part ■ Battery Pack 1. Push the battery latch in the direction shown below; then side the battery pack out of the slot.
Page 41 - ■ Hard Disk Drive; Remove the following parts in order before replacing this part.
40 Ch5. Removing and replacing a part ■ Hard Disk Drive Remove the following parts in order before replacing this part. 1. Battery Pack 1. Remove two screws as indicated in the picture.
Page 42 - Then pull the HDD assembly out in the direction shown below.
41 Ch5. Removing and replacing a part 2. Then pull the HDD assembly out in the direction shown below.
Page 43 - ■ Keyboard; Qty
42 Ch5. Removing and replacing a part ■ Keyboard Remove the following parts in order before replacing this part. 1. Battery Pack 1. Remove 2 screws. 2 M2.5 x L6.5 1SZZBA4097A 1 Qty Specification FRU No. No.
Page 44 - Remove keyboard and disconnect Keyboard cable.
43 Ch5. Removing and replacing a part 2. To remove 4 hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard, and pull it up. 3. Remove keyboard and disconnect Keyboard cable.
Page 46 - ■ Optical Disk Drive
45 Ch5. Removing and replacing a part ■ Optical Disk Drive Remove the following parts in order before replacing this part. 1. Battery Pack 2. Keyboard 3. BMDC(MDC) Modem Card 1. Remove 2 screws. 2 M2.0 X L4.5 1SZZBA4019F 1 Qty Specification FRU No. No. 2. Remove a screw, insert a screwdriver into th...
Page 47 - ■ Keyboard Deck
46 Ch5. Removing and replacing a part ■ Keyboard Deck Remove the following parts in order before replacing this part. 1. Battery Pack 2. Hard Disk Drive 1. Remove 17 screws. 14 M2.5 X L6.5 1SZZBA4097A 1 3 M2.0 X L3.0 1SZZBA4017A 2 Qty Specification FRU No. No. 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2. Re...
Page 49 - ■ Fan Assembly
48 Ch5. Removing and replacing a part ■ Fan Assembly Remove the following parts in order before replacing this part. 1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 1. Remove 8 screws and then remove FAN Assembly. 2 1 1 22 22 2 2 1 3 M2.0 X L12.0 1SZZBZ4022A 1 5 M2.0 X L3.5 1SZZBA402...
Page 50 - ■ Wireless LAN Card
49 Ch5. Removing and replacing a part ■ Wireless LAN Card Remove the following parts in order before replacing this part. 1. Battery Pack 1. Remove Cover Mini PCI screws. 2. Disconnect WLAN antenna cable and remove WLAN card.
Page 51 - ■ Display Module
50 Ch5. Removing and replacing a part ■ Display Module 2. Remove 2 Hinge cover screws. 3. Remove cap hinge small. (Applied both left and right side.) 1. Remove Wireless cable from hole. Remove LCD connector. You will see a tag designed to make the work easier. Pull out the tag. 2 M2 X L3.5 1SZZBA402...
Page 52 - Disconnect LCD connector and Modem connector.
51 Ch5. Removing and replacing a part 4. Disconnect LCD connector and Modem connector. Remove WLAN antenna.
Page 53 - Remove 2 Hinge Screws and remove Hinge.
52 Ch5. Removing and replacing a part 5. Remove 2 Hinge Screws and remove Hinge. 2 M2.5 X L6.5 1SZZBA4097A 1 Qty Specification FRU No. No. 6. Remove screw cover and remove 2 Hinge screws. (Applied both left and right side.) 4 M2.5 X L6.5 1SZZBA4097A 1 Qty Specification FRU No. No.
Page 55 - ■ Speaker
54 Ch5. Removing and replacing a part ■ Speaker Remove the following parts in order before replacing this part. 1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 1. Disconnect MIC cable. 2. Remove Speaker from Guide Boss.
Page 56 - Disconnect connector and remove Speaker.
55 Ch5. Removing and replacing a part 3. Disconnect connector and remove Speaker.
Page 57 - ■ Sub Board
56 Ch5. Removing and replacing a part ■ Sub Board 1. Remove 4 screws and remove Sub B/D. Remove the following parts in order before replacing this part. 1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 5. Optical Disk Drive 6. Display Module 4 M2.5 x L6.0 1SZZBA4080G 1 Qty Specificati...
Page 58 - ■ Main Board; Remove 5 Main Board screws and remove 2 Frame Hinge Left screws.
57 Ch5. Removing and replacing a part ■ Main Board 1. Remove Cover Block HDD. 2. Remove 5 Main Board screws and remove 2 Frame Hinge Left screws. 2 M2.5 X L6.0 1SZZBA4080G 1 5 M2 X L3.5 1SZZBA4023A 2 Qty Specification FRU No. No. Remove the following parts in order before replacing this part. 1. Bat...
Page 60 - ■ Display Module Exploded View
59 Ch5. Removing and replacing a part ■ Display Module Exploded View Remove the following parts in order before replacing this part. 1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 1. Using a knife, remove the logo and rubbers that are covering the screws. Then remove all 8 screws. 8...
Page 63 - Remove LCD power cable and remove Inverter.
62 Ch5. Removing and replacing a part 4. Remove LCD power cable and remove Inverter. 5. (Left, Right) Remove 4 Hinge screws. 4 M2.5 x L4.5 1SZZBA4080F 1 Qty Specification FRU No. No.
Page 86 - ■ Woofer
85 Ch5. Removing and replacing a part ■ Woofer Remove the following parts in order before replacing this part. 1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 5. Optical Disk Drive 6. Fan Assembly 7. Speaker 1. Remove Audio Sub Board. Remove 3 Screws. 3 M2.5xL11, D7(3.5) 1SZZBZ4023A ...
Page 87 - Disconnect connector and remove Woofer.
86 Ch5. Removing and replacing a part 2. Disconnect connector and remove Woofer.
Page 89 - Remove 6 Main Board screws. Remove 2 ODD interface Board screws.
88 Ch5. Removing and replacing a part 2. Remove 6 Main Board screws. Remove 2 ODD interface Board screws. Remove Main board and ODD board. 3 2 3 2 2 2 2 2 1 1 2 2 8 M2.0 X L3.5 1SZZBA4023A 2 2 M2.0 X L2.7 1SZZBZ4002B 1 2 M2.0 X L6.0 1SZZBA4080G 3 Qty Specification FRU No. No.
Page 98 - Chapter 6. Part lists
97 Ch6. Part lists Chapter 6. Part lists 2005-01-31 HTW09 LCD Front case 17.1" Case Assy Front with Tape 3111B97115A HWL17 LCD 단품 LP171W02-A4 LG PHILPS TFT COLOR WSXGA+ 1680X1050 LVDS 170NITS GLARE 6304FLP165A HWL16 LCD 단품 LP171WX2-A4K1 LG PHILPS TFT COLOR WXGA+ 1440X900 LVDS 200NITS GLARE 6304F...
