LG 65EV5C-2 - User Manual

ENGLISH 6 Precautions for Moving the Product WARNING • Make sure to turn off the product. - You may be electrocuted or the product can be damaged. • Make sure to remove all cables before moving the product. - You may be electrocuted or the product can be damaged. • When lifting or moving the product...

ENGLISH 7 Precautions for Using/Cleaning the Product WARNING • Do not attempt to disassemble, repair or modify the product yourself. - Fire or electric shock can occur. - Contact LG Customer Service for repair. • When cleaning the product, unplug the power cord and scrub gently with a soft cloth to ...

ENGLISH 8 LICENSES Supported licenses may differ by model. For more information of the licenses, visit www.lg.com . The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

ENGLISH 9 ASSEMBLY AND PREPARATION CAUTION • Always use genuine components to ensure safety and product performance. • The product warranty will not cover damage or injury caused by the use of counterfeit components. • Connect the power cord to the product before you plug it into a wall outlet. Plug...

ENGLISH 10 STORAGE METHOD FOR PANEL PROTECTION Correct Method 1 If the product needs to be set upright, hold both sides of the product and make sure that the panel does not touch the floor. Panel 2 When laying down the product, lay a cushion on a flat floor. Put the product on it with the panel of t...

ENGLISH 12 Cautions for connecting Video Wall Panels 1 Please use suction cups to secure the display while connecting. Maximum absorption 10 kg Handle size 180 mm Vacuum cup size 85 mm Anti-static pad (Rubber or Silicon) 2 Do not touch the back-side of panels.

ENGLISH 13 Installing on the Wall When installing the monitor on the wall, use the screws provided with the product. Install the monitor at least 100 mm away from the surfaces on each side of the monitor to ensure sufficient ventilation. Refer to the installation manual for detailed instructions on ...

ENGLISH 15 REMOTE CONTROL This manual describes how to operate the product using the remote control. Please read this manual carefully to use the monitor correctly.To replace the batteries, open the battery cover, match the and ends of the replacement batteries (1.5 V AAA) to the label inside the co...

ENGLISH 17 MAKING CONNECTIONS You can connect various external devices to your monitor. Change the input mode and select the external device you want to connect. For more information about external device connections, see the user manual provided with each device. Connecting to a PC Some of the cabl...

ENGLISH 19 Using the Input List (HOME) → • HDMI → DISPLAYPORT → USB

ENGLISH 20 Connecting Multiple Products To use multiple products connected to each other, connect one end of the signal input cable (DP cable) to the DP Out connector of Monitor 1 and connect the other end to the DP In connector of a connected product. Monitor 1 Monitor 2 Monitor 3 Monitor 4 NOTE • ...

ENGLISH 21 TROUBLESHOOTING No image is displayed. Problem Action Is the product power cord connected? • Check if the power cord is correctly plugged into the power outlet. Does the “Invalid Format” message appear? • The signal from the PC (Graphics card) is out of the vertical or horizontal frequenc...

ENGLISH 24 PRODUCT SPECIFICATIONS The product specifications below may change without prior notice to improve the features of the product.The symbol refers to alternating current, and refers to direct current. OLED panel Screen type Thin Film Transistor (TFT)OLED panel Operating conditions Daily usa...

www.lg.com Please read this manual carefully before operating your set and retain it for future reference. webOS 3.0 USER GUIDE LG Digital Signage (MONITOR SIGNAGE)

ENGLISH _inde x 2 TABLE OF CONTENTS USER SETTINGS ............................3 -Main Menu Settings ........................................................3 Picture SettingsSound SettingsNetwork SettingsGeneral Settings ENTERTAINMENT ...................... 15 -Using Multimedia Features................

ENGLISH _inde x 3 NOTE • The software-related contents may be changed without prior notice due to upgrade of the product functions. • Some features described in the User Guide may not be supported in certain models. • SNMP 2.0 is supported. USER SETTINGS Main Menu Settings Picture Settings To Select...

ENGLISH _inde x 7 Sound Settings • Only applies to certain models. To select a Sound Mode / [Sound] [Sound Mode] The best sound quality will be selected automatically depending on the video type currently being watched. • [Standard]: This sound mode works well for content of all types. • [Cinema]: O...

ENGLISH _inde x 9 Network Settings To Set a Signage Monitor Name / [Network] [Signage Name] You can set a name for Signage Monitor that will be used on the network by using the on-screen keyboard. To Set Your Wired Network / [Network] [Wired Connection (Ethernet)] • Connecting to a wired network: Co...

ENGLISH _inde x 12 General Settings To configure the language / [General] [Menu Language] Select one of the languages on the menu displayed on the screen. • [Menu Language]: Sets a language for Signage. Setting up the keyboard language / [General] [Keyboard Languages] Select the language you wish to...

ENGLISH _inde x 15 ENTERTAINMENT Using Multimedia Features Connecting USB/SD Storage Devices Connect a USB storage device such as a USB flash memory, SD storage devices or an external hard drive to the display and use multimedia features. CAUTION • Do not turn the monitor off or remove the USB stora...

ENGLISH _inde x 18 Photo & Video • The photo feature is not supported in OLED models. Supported Photo & Video Files Supported External Subtitle Format • *.smi, *.srt, *.sub (MicroDVD, SubViewer 1.0/2.0), *.ass, *.ssa, *.txt (TMPlayer), *.psb (PowerDivX), *.dcs (DLP Cinema) NOTE • Subtitles a...

ENGLISH _inde x 20 Viewing Photos and Videos / 1 Select your desired storage device. 2 Select and view your desired photo or video. Tips for Playing Video Files • Some user-created subtitles may not work properly. • Some special characters in subtitles are not rendered. • HTML tags are not supported...

ENGLISH _inde x 21 Scheduled Playing • Only applies to certain models. You can schedule your selected content to play at a certain time. (Scheduled playing is available with external inputs.) / 1 Select your desired storage device. 2 Enter the folder that contains the file you wish to schedule. 3 Cl...

ENGLISH _inde x 22 Music Supported Music Files • Some of the models that do not support the audio output cannot play the music. File Format Item Information .mp3 Bit rate 32 Kbps to 320 Kbps Sample freq. 16 KHz to 48 KHz Support MPEG1, MPEG2 Channels Mono, Stereo .wav Bit rate - Sample freq. 8 kHz t...

ENGLISH _inde x 23 SuperSign Contents Plays stored files using the Export option in SuperSign Editor. To play back the stored files using the Export option / Only contents distributed by SuperSign Manager are displayed and selectable. If there is a USB/SD storage device connected, the image on the U...

ENGLISH _inde x 24 Local Contents Scheduler • Only applies to certain models. • The recommended resolution for scheduled photo playback is 4096 x 2160 or below. Setting a Scheduled Playing You can create a scheduled playing using the Local Contents Scheduler and the Photo & Video app. Scheduled ...

ENGLISH _inde x 25 Screen Share • Only applies to certain models. Allows the screens of devices such as a mobile device or Windows PC to be displayed on the monitor via wireless connections such as WiDi or Miracast. Using Screen Share / 1 Connect according to the instructions provided by the guide t...

ENGLISH _inde x 26 Group Manager • Only applies to certain models. Using this template-based content editing program, you can produce, manage and play content. There are three modes: Master, Slave and StandAlone. The program can be used to distribute and play schedules between the Master and Slave. ...

ENGLISH _inde x 28 Leveler Tool • Only applies to certain models. You can check whether the product is horizontally and vertically level when installing the product outdoors in an enclosure. Accessing the Leveler Tool / You can check whether the product is horizontally and vertically level. Exiting ...

ENGLISH _inde x 29 Control Manager • Only applies to certain models. You can control and check the status of the display through web browser.This function is available on PC and mobile device. CAUTION • Supported resolutions (this program is optimized for the following resolutions): - 1280 x 1024 / ...

ENGLISH _inde x 30 How to Use On a PC 1 Enter ‘ https://Product IP address:3737 ’ in the browser's address bar to access the Control Manager login page. 2 Enter the password in the Password window (The default password is ‘000000’). 3 Click the Login button after entering the password to access the ...

ENGLISH _inde x 31 Follow the steps below if you encounter issues with your security certificate while attempting to access. On Chrome 1 Click 'ADVANCED' 2 Click 'Proceed to product IP address (unsafe)'

ENGLISH _inde x 35 PICTURE ID Settings • Only applies to certain models. [PICTURE ID] is used to change the settings of a specific set (display) using a single IR receiver for multi- vision. Communication is possible between a monitor with an IR receiver and other monitors using RS-232C cables. Each...

ENGLISH _inde x 36 IR CODES All models do not support the HDMI/USB function.Some key codes may not be supported depending on the model. Code (Hex) Function Remarks 08 (POWER) Remote control button C4 MONITOR ON Remote control button C5 MONITOR OFF Remote control button 95 (Energy Saving) Remote cont...

ENGLISH _inde x 38 TO CONTROL MULTIPLE PRODUCTS • Only applies to certain models. Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC.In the Option menu, the Set ID must be between 1 and 1000 without being duplicate...

ENGLISH _inde x 39 Communication Parameter Baud Rate: 9600 bpsData Length: 8 bitParity Bit: NoneStop Bit: 1 bitFlow Control: NoneCommunication Code: ASCII code NOTE • When using three-wire connections (non-standard), an IR daisy chain cannot be used. • Be sure to only use the provided gender to conn...

ENGLISH _inde x 40 Command Reference List COMMAND DATA (Hexadecimal) 1 2 01 [Power] k a 00 to 02 02 [Select input] x b See [Select Input] 03 [Aspect Ratio] k c See [Aspect Ratio] 04 [Energy Saving] j q See [Energy Saving] 05 [Picture Mode] d x See [Picture Mode] 06 [Contrast] k g 00 to 64 07 [Bright...

ENGLISH _inde x 44 Transmission/Reception Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] * [Command1]: Identifies between the factory setting and the user setting modes.* [Command2]: Controls monitor sets.* [Set ID]: Used for selecting a set you want to control. A unique Set ID c...

www.lg.com Please read this manual carefully before operating the your set and retain it for future reference. webOS 3.0 INSTALLATION MANUAL LG Digital Signage (MONITOR SIGNAGE)

CONTENTS ACCESSING INSTALLATION MENU .............................................4 INSTALLATION MENU ..................5 -Signage Setup.....................................................................5 Power On StatusWake On LANLAN Daisy ChainPower Off ManagementRotationBeaconBaudrate (9600/115...

ACCESSING INSTALLATION MENU 1 Press and hold the SETTINGS button for 5 seconds. or 2 When Input ID (The top right corner ) is displayed, enter your password. (The default value is 0, 0, 0, 0 ) 3 When the Installation Menu is displayed, select the desired option. - Signage Setup - USB Cloning - Passw...

INSTALLATION MENU NOTE • Some features described in the Installation manual may not be supported in certain models. Signage Setup Use this menu to configure the digital signage after installation. Power On Status • You can select the operating status of the monitor when the main power is switched on...

Power Off Management • No Signal Power Off (15 Min) - You can choose whether to use the 15 min force off feature. - You can set this option to On or Off. - If you set this option to On, the product turns off when it has remained in no signal status for 15 minutes. - If you set this option to Off, th...

Rotation • OSD Portrait Mode - This feature allows you to rotate the OSD clockwise. - You can set this feature to Off/90/180/270. (Some models only support certain settings.) - If you set this feature to Off, the feature is disabled. - If you set this feature to 90, the OSD rotates 90 degrees clockw...

Beacon • Enables BLE Beacon, one of Bluetooth 4.0's features. • Beacon Mode (on/off toggle): Enables the Beacon feature. • Supports LG Beacon/iBeacon/Eddystone Type Beacon features. • LG Beacon/iBeacon - Beacon UUID (hex): Sets the UUID. 1. Field1: 4byte hex value (8 digits)2. Field2: 2byte hex valu...

Power On Delay (0 ~ 250) • This feature delays power on in order to prevent overload when multiple monitor sets are turned on simultaneously. • You can set the delay interval in the range of 0 to 250 seconds. Check Screen • The Check Screen feature judges whether there are abnormalities at the edges...

Sync Mode • Syncs the products to the time, brightness and content of one product. • Off: Sync is disabled. • RS-232C: Syncs multiple monitors connected via RS-232C. - Master/Slave: These monitors can be set to Master or Slave. Only one monitor should be set to Master mode for this feature to work p...

Application • Adds/deletes applications in the Launcher bar. • We recommend that if you are to remove the Screen Share app from the home launcher by unchecking the Screen Share item, you should reboot your system after removal. • When Content Rotation or OSD Portrait Mode is set to On, the 'Group Ma...

Status Message • Sets up a feature that sends the status of Signage to users' email addresses. • The administrator can set Status Message to On or Off. • Messaging Period: Sets a time interval to send messages. You can select either When Failure Status or Weekly. • Select Date: Available if you have...

SIMPLINK Setup • When the SIMPLINK Setup is set to On, you can use the SIMPLINK provided by LG Signage. • Device ID: S ets the ID of the device connected via CEC wiring. You can choose a value between 'All' and 'E'. • StandBy: Sets the scenarios for sending and receiving the OpStandBy (0x0c) command...

Analog Signage BLU Setting • Sets the function to control the Analog Signage BLU. • On/Off Time Setting: Adjusts the schedule of the BLU. • BLU Manual On/Off: Use the On or Off setting to set the BLU to On or Off without being associated with the schedule function. Crestron • This function enables s...

Signage 365 Care • You can install the Signage 365 Care (fault diagnosis) solution for fault diagnosis and prediction service. • Install: Installs the Signage 365 Care solution.1) ENTER ACCOUNT NUMBER: Enters the 6-digit account number to install the Signage 365 Care solution. - Account Number: The ...

Guide to Using Content Rotation [Portrait installation setting] You can turn the image into a portrait image using Content Rotation.When installing the display rotated 90 degrees: Set Content Rotation to 270.When installing the display rotated 270 degrees: Set Content Rotation to 90.Example) When in...

USB Cloning You can copy the product settings to other sets. Send to USB • You can save the current settings in file format to a USB device. • Select the file name and press the OK button to complete • Items not saved: Current Time, Power On Delay, Set ID, items under Network, White Balance, Tile ID...

Fail Over The input source with the highest priority will be selected. Off • The Auto-Fail Over feature is disabled. Auto • The input source changes according to the specified order. When several input sources are found, the input source with the highest priority will be selected. • PriorityCase 1) ...

ISM Method If a still image is displayed on the screen for an extended period of time, image sticking can occur. The ISM method is a feature that prevents image sticking. Mode • Selects the desired ISM Method mode. • Normal: Disables the ISM method. • White Wash: Displays a white pattern to remove i...

Bar Image Download • To download an image, the image file must be located under the folder titled "ISM" on your USB drive. • Make sure to delete the old images stored in the internal memory before downloading a new image file. • Supported image file types: "BMP", "JPG", "...

Server Set Automatically • The monitor settings will be set automatically so that the SuperSign server can search it. Server IP Type • Select the IPv4 or the IPv6 type. Server IP • This is a menu where you can set an IP address for the SuperSign server. Server Status • Server Status displays the sta...

Lock Mode USB • You can prevent the use of USB devices. OSD • You can prevent OSD from displaying. Wi-Fi • This feature enables you to turn the Wi-Fi feature on or off. Reset to Initial Settings • You can restore the initial settings with this feature. IR Operation • If you set IR Operation to Norma...