Page 3 - Contents; iii
Contents Safety information . . . . . . . . . . iii Products that are not assessed . . . . . . . . . x Chapter 1. General information . . . . . 1 Introduction . . . . . . . . . . . . . . . . . 1 Server documentation . . . . . . . . . . . . . 2 Chapter 2. Server setup road map . . . 5 Chapter 3. Prod...
Page 4 - ii
Installing or removing the ThinkServer RAID700 Battery . . . . . . . . . . . . . . 111 Installing or removing the expander card. . . 114 Installing or removing an Ethernet card . . . 118 Installing or removing the ThinkServer RAID300 Upgrade Key for Advanced RAID . . . . 123 Installing or removing t...
Page 5 - Safety information; documentation DVD that comes with the product.; 제품을 사용하기 전에 제품과 함께 제공되는 문서 DVD의 다국어 안전 지침을 주의 깊게 읽어보십시오.
Safety information Note: Before using the product, be sure to read and understand the multilingual safety instructions on the documentation DVD that comes with the product. Antes de usar o produto, leia e entenda as instruções de segurança multilíngues no DVD de documentaçãoque o acompanha. Преди да...
Page 6 - iv
Przed skorzystaniem z produktu należy zapoznać się z wielojęzycznymi instrukcjami bezpieczeństwaznajdującymi się na płycie DVD z dokumentacją dostarczoną wraz z produktem. Antes de utilizar o produto, leia atentamente as instruções de segurança multilingues que constam noDVD de documentação fornecid...
Page 7 - To avoid a shock hazard:
Statement 1 DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of thisproduct during an electrical storm. • Connect all power cords to a pr...
Page 11 - ix
Statement 16 CAUTION:To reduce the risk of electric shock or energy hazards: • This equipment must be installed by trained service personnel in a restricted-access location, as defined by your local electrical code and the latest edition of IEC 60950. • Connect the equipment to a reliably earthed sa...
Page 12 - Products that are not assessed; Typical products that are; not assessed; include but not limited to the following:
Statement 20 CAUTION:A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace thebattery only with the Lenovo-approved part. Recycle or discard the battery as instructed by localregulations. Products that are not assessed Typical products that are not assessed...
Page 13 - Chapter 1. General information; Introduction; ThinkServer EasyStartup
Chapter 1. General information This chapter provides some general information about your product. This chapter contains the following items: • “Introduction” on page 1 • “Server documentation” on page 2 Introduction This documentation for your Lenovo ® ThinkServer ® product contains information abou...
Page 14 - Server documentation; Printed documents; Read Me First
Record information about your server in the following table. You will need the information if you ever needto have your server serviced. For where to find the product information label on the chassis, see “Machine type, model, and serial numberlabel” on page 14. Product name ________________________...
Page 15 - Documentation DVD; Windows
Documentation DVD The documentation DVD, which comes with your server, contains various documents for your server inPortable Document Format (PDF) and HyperText Markup Language (HTML). The documentation DVD is notbootable. To view the documents on the DVD, you will need a computer with a Web browser...
Page 16 - Supplementary documents
Supplementary documents Depending on your server, your documentation DVD might contain supplementary documents provided byLenovo, including documents for Ethernet cards, host bus adapters (HBAs), or other optional parts. 4 ThinkServer RD440 User Guide and Hardware Maintenance Manual
Page 17 - Chapter 2. Server setup road map; Rack
Chapter 2. Server setup road map This chapter provides a general road map to guide you through setting up your server. The server setup procedure varies depending on the configuration of the server when it was delivered. Insome cases, the server is fully configured and you need to connect the server...
Page 19 - Chapter 3. Product overview; Server package
Chapter 3. Product overview This chapter provides information about the server package, features, specifications, software programs,and component locations. This chapter contains the following items: • “Server package” on page 7 • “Features” on page 8 • “Specifications” on page 12 • “Software” on pa...
Page 20 - Features; Personal Systems Reference; Microprocessor
Features This topic provides general information about the server features for various models. Depending on yourspecific model, some features might vary or unavailable. For information about your specific model, use theSetup Utility program. See “Viewing information in the Setup Utility program” on ...
Page 22 - Security features; fault tolerance (see “Configuring RAID” on page 74); Basic system management features; – BIOS Setup Utility program
• Security features – Administrator password and user password to help you protect unauthorized access to the server (see “Using passwords” on page 67) – Hot-swap redundant power supplies to protect against significant interruption to the operation of the system when a power supply fails (for server...
Page 23 - Advanced system management features; ThinkServer Management Module
Your server supports onboard SATA software RAID. If a required RAID card is installed, your serveralso supports advanced SATA/SAS hardware RAID configurations. For detailed information, see“Configuring RAID” on page 74. – Status light-emitting diodes (LEDs) and diagnostic LEDs For more information a...
Page 24 - Specifications; This topic lists the physical specifications for your server.; Dimensions; Software
Specifications This topic lists the physical specifications for your server. Dimensions Width without rack handles: 442 mm (17.4 inches) Width with rack handles: 482.4 mm (19 inches) Depth without rack handles: 720.6 mm (28.37 inches) Depth with rack handles: 734 mm (28.9 inches) Height: 87.6 mm (3....
Page 25 - ThinkServer Management Module User Guide
also is on the DVD and can be accessed directly from the program interface. For detailed information, see“Using the ThinkServer EasyStartup program” on page 71. ThinkServer EasyUpdate Firmware Updater The ThinkServer EasyUpdate Firmware Updater program (hereinafter referred to as the Firmware Update...
Page 26 - Diagnostic programs; • ThinkServer Diagnostic Tool; Locations
Diagnostic programs The following diagnostic programs are available for you to diagnose server problems: • ThinkServer Diagnostic Tool • ThinkServer System Profile Collection Tool For more information, see “Using a diagnostic program” on page 204. Locations This topic provides information to help yo...
Page 28 - Front view of the server
For server models with twelve 3.5-inch hard-disk-drive bays, the machine type, model, and serial numberlabel is attached on the left side of the server. Figure 4. Label on server models with twelve 3.5-inch hard-disk-drive bays Front view of the server This topic provides information to help you loc...
Page 30 - Some server models come with a slim SATA optical drive.
3 Pull-out information card The machine type, model, and serial number label of the server is attached on the pull-out information card.See “Machine type, model, and serial number label” on page 14. 4 Front panel For detailed information about the controls, connectors, and status LEDs on the front p...
Page 31 - Front USB connectors
1 3.5-inch hard-disk-drive area The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied.The number of the installed hard disk drives in your server varies by model. The vacant hard-disk-drivebays are occupied by dummy hard-disk-drive trays. For server m...
Page 33 - the pull-out information card, and the slim optical drive bay.; Pull-out information card
Front view of server models with 2.5-inch hard-disk-drive bays The following illustration shows the front view of server models with 2.5-inch hard-disk-drive bays. Figure 9. Front view of server models with 2.5-inch hard-disk-drive bays 1 2.5-inch hard-disk-drive area (right cage) 5 Rack handle (lef...
Page 34 - Slim optical drive; Diagnostic panel; Front panel; This topic applies only to the following server models:
4 Slim optical drive Some server models come with a slim SATA optical drive. 5 Rack handle (left) 8 Rack handle (right) If your server is installed in a rack cabinet, you can use the rack handles to help you slide the server outof the rack cabinet; or use the rack handles and screws to secure the se...
Page 36 - : The server is off or the server is on and working correctly.; Amber; system errors and corresponding solutions.; Solution; Used to attach a VGA-compatible video device, such as a VGA monitor.; Diagnostic module
5 System error LED The system error LED helps you to determine if there are any system errors. • Off : The server is off or the server is on and working correctly. • Amber : The server has potential system errors. Check the information in the following table for potential system errors and correspon...
Page 37 - • Intelligent Diagnostics Module Premium (IDM Premium); Intelligent Diagnostics Module; table for potential errors and corresponding solutions.; LED
• Intelligent Diagnostics Module Premium (IDM Premium) Many errors are first indicated by a lit error LED on the diagnostic panel of the server. If an LED is lit, one ormore LEDs elsewhere in the server might also be lit to direct you to the source of the error. See “Systemboard LEDs” on page 59. In...
Page 38 - Intelligent Diagnostics Module Premium
Table 1. Potential errors and corresponding solutions (continued) LED Status Potential error Solution 4 Memory module status LED Solid on (amber) One or more memory modulesare overheated. Check the BMC for errors andrun the diagnostic programs. See“Using a diagnostic program” onpage 204. 5 Microproc...
Page 39 - System fan error LEDs; Status; • Your server has five system fans. The callout
1 System fan error LEDs The system fan error LEDs help you to determine if there are any system fan errors. Status Description Action Solid off The system fans are operating correctly. Solid on (amber) One or more system fans are running at lowspeed or have been removed. Check the BMC for errors and...
Page 40 - Ambient temperature limit LED
2 CPU1 DIMM status LEDs 3 CPU2 DIMM status LEDs The DIMM status LEDs help you to determine if there are any memory module errors. Status Description Action Solid off The memory modules are operating at anormal temperature. Solid on (amber) When a DIMM status LED is lit in amber, itindicates that the...
Page 41 - Rear view of the server; Expansion card installation guidelines; • Only one Host Bus Adapter can be installed.
5 Microprocessor status LEDs (also known as CPU status LEDs) The microprocessor status LED helps you to determine if the microprocessor is running at a normaltemperature. Status Description Action Solid off The microprocessors are operating at anormal temperature. Solid on (amber) The microprocessor...
Page 42 - The following illustration shows the rear view of the server.; Hot-swap redundant power supply 1
The following illustration shows the rear view of the server. Figure 16. Rear view of the server 1 Hot-swap redundant power supply 2 (available in some models) 7 VGA DB-15 connector 2 Hot-swap redundant power supply 1 8 Ethernet connector 1 (RJ-45) 3 PCI Express card area for cards on the riser card...
Page 43 - PCI Express card area for cards on the riser card assembly 2
3 PCI Express card area for cards on the riser card assembly 2 There are three PCI Express card slots on the riser card assembly 2 for installing Ethernet cards or othersupported PCI Express cards. Figure 17. Riser card assembly 2 PCI Express card slot Physical link width Negotiable link width Suppo...
Page 44 - PCI Express card area for cards on the riser card assembly 1; PCI Express card slot
4 PCI Express card area for cards on the riser card assembly 1 There are three PCI Express card slots on the riser card assembly 1. Figure 18. Riser card assembly 1 PCI Express card slot Physical link width Negotiable link width Supported card length and height 1 x8 x4, x2, x1 Half-length, full-heig...
Page 45 - USB connectors; Serial connector; Used to attach a device that uses a 9-pin serial connector.; ID LED
5 8 9 Ethernet connectors (RJ-45) Used to attach an Ethernet cable for a LAN. Each Ethernet connector has two status LEDs to help youidentify the Ethernet connectivity, activity, and connection speed. Note: The Ethernet connector 0 (callout 9 ) marked with “MGMT” is for system management by default....
Page 46 - Server components
Server components This topic provides information to help you locate the components of your server. For more informationabout major components, see the related topics in “Locations” on page 14. To remove the server cover and gain access to the inside of the server, see “Removing the server cover”on ...
Page 49 - CRU identification
Components of server models with 2.5-inch hard-disk-drive bays ID PSU Mem CPU 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Figure 22. Components of server models with 2.5-inch hard-disk-drive bays 1 Cooling shroud 13 Slim optical drive (available in some models) 2 Power supply cooling shroud 14 Diagnostic ...
Page 50 - FRU description
might require some technical skills or tools, or request that a technician install the optional-service CRUunder the terms of the applicable warranty service type for your country or region. Non-CRUs must be replaced only by trained service technicians. The following table lists the major FRUs in yo...
Page 51 - Each hot-swap hard disk drive has two status LEDs on the front.; Description
Hot-swap hard-disk-drive status LEDs Each hot-swap hard disk drive has two status LEDs on the front. Figure 23. 3.5-inch hot-swap hard-disk-drive status LEDs Figure 24. 2.5-inch hot-swap hard-disk-drive status LEDs 1 Hard-disk-drive activity LED 2 Hard-disk-drive RAID status LED Description Off Off ...
Page 52 - RAID card; cables that are not required for your server.
RAID card This topic provides information to help you locate the connectors on the RAID card if a RAID card installedis in the longer slot of the riser card assembly 1. Some server models come with a RAID card to provide advanced SATA/SAS hardware RAID functions. Youalso can purchase a supported RAI...
Page 53 - ThinkServer RAID 700 Battery connector
ThinkServer RAID 700 Adapter (also known as ThinkServer 9260-8i SAS RAID Adapter) The following illustration shows the connectors on the ThinkServer RAID 700 Adapter. Figure 26. ThinkServer RAID 700 Adapter 1 Ports 7-4 3 ThinkServer RAID 700 Battery connector 2 Ports 3-0 1 Ports 7-4 Used to connect ...
Page 54 - ThinkServer RAID 710 Adapter (also known as 9270CV-8i RAID adapter); ThinkServer RAID Super Capacitor Module connector; Expander card
ThinkServer RAID 710 Adapter (also known as 9270CV-8i RAID adapter) The following illustration shows the connectors on the ThinkServer RAID 710 Adapter. Figure 27. ThinkServer RAID 710 Adapter 1 Port 1 3 ThinkServer RAID Super Capacitor Module connector 2 Port 2 1 Port 1 Used to connect a mini-SAS s...
Page 55 - To locate the backplanes, see “Server components” on page 34.
The following illustration shows the connectors on the expander card. Each connector on the expandercard is used to connect a mini-SAS to mini-SAS signal cable. For detailed information, see “Connectingthe cables” on page 47. Figure 28. Expander card 1 Connector 1 4 Connector 4 2 Connector 2 5 Conne...
Page 56 - -pin power connector; Used to connect a power cable to provide power to the backplane.; Optical drive power connector
The following illustrations show the connectors on the backplane for server models with eight 3.5-inchhard-disk-drive bays. Figure 29. Front view of the backplane for server models with eight 3.5-inch hard-disk-drive bays 1 Slot 0 for a 3.5-inch hard disk drive 5 Slot 7 for a 3.5-inch hard disk driv...
Page 57 - Signal cable connector
Backplane for server models with twelve 3.5-inch hard-disk-drive bays This topic provides information to help you locate the connectors on the backplane for server models withtwelve 3.5-inch hard-disk-drive bays. The following illustrations show the connectors on the backplane for server models with...
Page 59 - Connecting the cables; “Connecting cables from the RAID card to the backplane” on page 47; Connecting cables from the RAID card to the backplane
Figure 34. Rear view of the backplane for server models with 2.5-inch hard-disk-drive bays 1 8-pin power connector 3 Mini-SAS ports 0-3 2 Mini-SAS ports 4-7 4 Optical drive power connector 1 8-pin power connector Used to connect a power cable to provide power to the backplane. 2 Mini-SAS ports 4-7 U...
Page 63 - Connecting cables from the system board to the backplane
Use the following instructions to connect cables from the expander card to the backplane for twelve 3.5-inchhard disk drives: 1. For hard disk drive 0 to hard disk drive 3, use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector 1 on one end of the cable to the connector 3 on the ...
Page 64 - “System board components” on page 52; System board components
connect the mini-SAS connector on the other end of the cable to the mini-SAS ports 0-3 on thebackplane. 2. If your server has more than four hard disk drives installed, for hard disk drive 4 to hard disk drive 7, use another mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one...
Page 65 - Reserved for the manufacturer.
7 SAS connector 4-7 23 System fan 6 connector 8 SAS connector 0-3 24 Microprocessor socket 2 9 Coin-cell battery 25 System fan 5 connector 10 Platform Controller Hub (PCH) 26 Memory slots (6) 11 Internal USB Type A connector 2 27 System fan 3 connector 12 TMM Premium connector 28 Microprocessor sock...
Page 67 - Used to connect the power cables from the backplane.; System board jumpers and switches
21 Backplane power connector 1 22 Backplane power connector 2 Used to connect the power cables from the backplane. 23 25 27 29 31 System fan connectors There are five hot-swap system fans and one dummy system fan installed in the system fan cage in yourserver. Each system fan connector is used to co...
Page 68 - Clear CMOS jumper; Clearing CMOS does not erase your BIOS passwords.
The following illustration shows the status of the jumpers and switches on the system board of your server.You can configure, recover, enable, or disable some specific features of the system board by setting thejumpers and switches. Figure 40. System board jumpers and switches 1 Clear CMOS (Compleme...
Page 70 - System board switches; There are four switches on the system board of your server.; BIOS recovery switch; Used to erase forgotten passwords, such as the BIOS passwords.
3 System board switches There are four switches on the system board of your server. Figure 41. System board switches 1 BIOS recovery switch 3 Management Engine (ME) in force update switch 2 Clear password switch 4 Reserved for the manufacturer 1 BIOS recovery switch Used to recover the BIOS if the p...
Page 71 - ME in force update switch; Rack Installation Instructions; System board LEDs
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and plac...
Page 72 - TMM status LED (also known as BMC status LED); TMM status LED
Note: Depending on the model, your server might look slightly different from the illustrations in this topic. The server is designed so that LEDs remain lit when the server is connected to an ac power source but is notturned on, if the power supply is operating correctly. This helps you to isolate p...
Page 73 - Chapter 4. Turning on and turning off the server; Turning on the server; The server can be turned on in one of the following ways:; Turning off the server; The server can be turned off in one of the following ways:
Chapter 4. Turning on and turning off the server This chapter provides information about turning on and turning off the server. Turning on the server The server can be turned on in one of the following ways: • After you finish unpacking and setting up the server, connect it to an ac power source. Pr...
Page 74 - for the operating system.
• The server might be turned off as an automatic response to a critical system failure. Notes: • When you turn off the server and leave it connected to an ac power source, the server also can respond to a remote request to turn on the server. To remove all power from the server, you must disconnectt...
Page 75 - Chapter 5. Configuring the server; Using the Setup Utility program; Main
Chapter 5. Configuring the server This chapter provides the following information to help you configure the server: • “Using the Setup Utility program” on page 63 • “Using the ThinkServer EasyStartup program” on page 71 • “Configuring RAID” on page 74 • “Configuring the Ethernet controllers” on page...
Page 76 - Setup Utility program interface; Main menu
– Select SATA/SAS Configuration and follow the instructions on the screen to view information about the installed SATA or SAS devices, such as a hard disk drive or an optical drive. • On the Server Management menu, select System Information to view information about your system. Setup Utility progra...
Page 78 - Setting the system date and time
• Erase SEL : Erase system event log (SEL). • System Information : View basic information about your server. • BMC Network Configuration : Set BMC configuration parameters. • System Location : View and configure the location information. Boot Options menu The Boot Options menu in the Setup Utility p...
Page 79 - Using passwords; Setup Utility program password types; Administrator password; Password considerations
3. Use the Tab key to switch between data elements and type the numbers from the keyboard to set the system date and time. 4. Press F10 to save settings and exit the Setup Utility program. Using passwords By using the Setup Utility program, you can set a password to prevent unauthorized access to yo...
Page 81 - Setting the mode of the Ethernet connectors; Ethernet connector for system management; Exiting the Setup Utility program
4. Press F10 to save settings and exit the Setup Utility program. The server will restart to enable the TPM function. Setting the mode of the Ethernet connectors There are three RJ-45 Ethernet connectors on the rear of the server. The Ethernet connector 0 is for systemmanagement by default. However,...
Page 82 - Updating or recovering the BIOS; Save as User Defaults
Updating or recovering the BIOS This topic provides instructions on how to update the BIOS and how to recover from a POST and BIOSupdate failure. System programs are the basic layer of software built into your server. System programs include the POST,the UEFI BIOS, the Setup Utility program, and the...
Page 83 - Recovering from a BIOS update failure; Using the ThinkServer EasyStartup program
• Check and reconfigure the BIOS settings for your specific needs based on your note or refer to “Using the Setup Utility program” on page 63. Recovering from a BIOS update failure If the power to your server is interrupted while the BIOS is being updated, your server might not restartcorrectly. If ...
Page 84 - Features of the ThinkServer EasyStartup program; Starting the ThinkServer EasyStartup program; User Guide
If you do not have a ThinkServer EasyStartup DVD, you also can download an ISO image from the Lenovo Support Web site and make a disc by yourself. To download the ThinkServer EasyStartup program image and burn it into a disc, do the following: 1. Go to http://www.lenovo.com/drivers and follow the in...
Page 86 - Configuring RAID
• Download drivers This menu helps you download the required device drivers from the ThinkServer EasyStartup DVD to a removable storage device so that you can easily get the drivers for server configuration when you needthem. Note: The most up-to-date device drivers for various server models are alw...
Page 87 - About RAID
• “Configuring RAID using the ThinkServer EasyStartup program” on page 76 • “Configuring the ThinkServer RAID 300” on page 76 • “Configuring the advanced SATA/SAS hardware RAID” on page 82 About RAID RAID, an acronym for Redundant Array of Independent Disks, is a technology that provides increasedst...
Page 88 - Configuring RAID using the ThinkServer EasyStartup program; Configuring the ThinkServer RAID 300
• RAID 10 : a combination of RAID 0 and RAID 1 RAID 10 consists of striped data across mirrored spans. A RAID 10 drive group is a spanned drivegroup that creates a striped set from a series of mirrored drives. RAID 10 allows a maximum of eightspans. You must use an even number of drives in each RAID...
Page 89 - RAID array status; The RAID array status can be one of the following:; Online; Starting the LSI Software RAID Configuration Utility program
10 by default. You also can activate RAID 5 by installing a ThinkServer RAID 300 Upgrade Key for AdvancedRAID. See “Installing or removing the ThinkServer RAID 300 Upgrade Key for Advanced RAID” on page 123. You can install and use the MegaRAID Storage Manager program to manage the RAID array and RA...
Page 92 - Setting a hot-spare drive; MegaRAID SAS Software User Guide; Rebuilding a physical drive; MegaRAID SAS Software User
To initialize a virtual drive using the LSI Software RAID Configuration Utility program, do the following: 1. Start the LSI Software RAID Configuration Utility program. See “Starting the LSI Software RAID Configuration Utility program” on page 77. 2. On the main interface of the program, select Init...
Page 95 - without encountering hardware problems.; Using the Lenovo ThinkServer EasyManage program
The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supportedoperating systems and device drivers on your server. See “Using the ThinkServer EasyStartup program”on page 71. The device drivers for onboard Ethernet controllers also are available for download a...
Page 98 - • Have a small flat-blade screwdriver available.; Handling static-sensitive devices; • Do not place the part on the server cover or other metal surface.
• Have a small flat-blade screwdriver available. • You do not have to turn off the server to install or replace a hot-swap redundant power supply, hot-swap hard disk drives, or hot-plug USB devices. However, you must turn off the server before performingany steps that involve installing, removing, o...
Page 99 - – Use the ground prong of the ac plug on ac-operated servers.; System reliability guidelines; with the options in addition to the instructions in this manual.; Working inside the server with the power on; • Do not allow your necktie or scarf to hang inside the server.; Removing the server cover
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. – When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems. – Use the ground prong of the ac plug on ...
Page 101 - Removing and reinstalling the front bezel
6. Fully open the cover latch 1 and slide the server cover to the rear until it is disengaged from the chassis. Then, lift the server cover off the chassis and set it aside. Note: It is recommended that you wait three to five minutes to let the server cool before removing the server cover. Figure 44...
Page 102 - Installing, removing, or replacing hardware
1. Remove the three screws 1 that secure the front bezel and then pivot the front bezel outward to remove it from the chassis. Figure 45. Removing the front bezel 2. To reinstall the front bezel, align the tabs on the bottom edge of the front bezel with the corresponding holes in the chassis. Then, ...
Page 103 - • Use only parts provided by Lenovo.; Removing and reinstalling the rack handles; bays” on page 91
Notes: • Use only parts provided by Lenovo. • Depending on the model, your server might look slightly different from the illustrations in this topic. The EMI integrity and cooling of the server are protected by having all drive bays and PCI card slots coveredor occupied. When you install an internal...
Page 106 - Go to “Completing the parts replacement” on page 199.; handle from the chassis.
c. Connect the signal cable of each rack handle to the corresponding signal cable connector on the backplane for server models with twelve 3.5-inch hard-disk-drive bays. Figure 50. Connecting the rack handle signal cables to the backplane 8. Go to “Completing the parts replacement” on page 199. Remo...
Page 107 - Removing and reinstalling the cooling shroud; To remove and reinstall the cooling shroud, do the following:
2. To reinstall the rack handles, insert the small tab 1 on the rack handle into the hole 2 in the chassis. Then, align the screw hole in the rack handle with the corresponding hole in the chassis and install thescrew to secure the rack handle on each side of the server. Figure 52. Installing the ra...
Page 108 - completely engage with both sides of the chassis.; Go to “Completing the parts replacement” on page 199.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 87. 4. Locate ...
Page 109 - Removing and reinstalling the left cage; To remove and reinstall the left cage, do the following:
Attention: For proper cooling and airflow, reinstall the cooling shroud before turning on the server. Operating the server with the cooling shroud removed might damage server components. Removing and reinstalling the left cage Attention: Do not open your server or attempt any repair before reading a...
Page 111 - Installing or removing a memory module; Memory module installation rules
10. Ensure that the two screw holes in the rear of the left cage are aligned with the corresponding holes in the chassis. Then, install the two screws to secure the left cage in position. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 MEM 1 PSU 1 2 1 2 3 4 5 6 MEM 2 1 2 3 4 5 6 7 8 9 10 11 12 CPU 1 2 1 2 3 4...
Page 113 - CPU1 DIMM
The following table explains the memory module installation rules for servers that have only onemicroprocessor (CPU1) installed. The “X” mark indicates the memory slots into which the memory modulesshould be installed in different situations. Figure 59. CPU1 DIMMs Table 3. Memory module installation...
Page 114 - Installing a memory module; See “Memory module installation rules” on page 99.
The following table explains the memory module installation rules for servers that have two microprocessors(CPU1 and CPU2) installed. The “X” mark indicates the memory slots into which the memory modulesshould be installed in different situations. Figure 60. CPU1 DIMMs and CPU2 DIMMs Table 4. Memory...
Page 116 - Removing a memory module
10. Reconnect any cables that you have disconnected. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 199. Removing a memory module Attention: Do not open your server or attempt ...
Page 117 - Installing or removing the RAID card; Installing the RAID card
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to “Completing the parts replacement” on page 199. Installing or removing the RAID card This topic provides instructions on how to install or remove the RAID card. If you...
Page 118 - outside of the server. Then, take the new RAID card out of the package.
6. There are two PCI Express card slots on the riser card assembly 1 and the longer one is for installing the RAID card. Remove the slot bracket for the longer slot and store it in case you later remove the RAIDcard and need the bracket to cover the place. Figure 64. Removing a PCI Express card slot...
Page 119 - Removing the RAID card
10. Connect cables depending on your specific server configuration. See “Connecting the cables” on page 47. 11. Reinstall the riser card assembly 1. See “Replacing the riser card assembly 1” on page 176. What to do next: • To work with another piece of hardware, go to the appropriate section. • To c...
Page 120 - See “Replacing the riser card assembly 1” on page 176.; materials that are supplied to you for shipping.
5. Remove the riser card assembly 1 and lay it upside down on a flat, clean, and static-protective surface. See “Replacing the riser card assembly 1” on page 176. 6. If there is an expander card installed on the riser card assembly 1, you might need to remove the expander card first for easier opera...
Page 121 - Installing the TR 500 Key
The TR 500 Key expands the capability of the ThinkServer RAID 500 Adapter by activating RAID 5 and RAID50 for advanced SATA/SAS hardware RAID. You can purchase a TR 500 Key from Lenovo. Installing the TR 500 Key Attention: Do not open your server or attempt any repair before reading and understandin...
Page 122 - Removing the TR 500 Key; system after removing the TR 500 Key.
6. Locate the RAID 5 key connector on the ThinkServer RAID 500 Adapter and then carefully insert the TR 500 Key into the connector. If necessary, you can remove the ThinkServer RAID 500 Adapter first,install the TR 500 Key on it, and then reinstall the ThinkServer RAID 500 Adapter. See “Installing o...
Page 123 - packaging materials that are supplied to you for shipping.; Installing or removing the ThinkServer RAID 700 Battery
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and plac...
Page 124 - Installing the TR 700 Battery
alternative to using an uninterruptible power supply, and a second level of fault tolerance when used with anuninterruptible power supply. The temperature of the TR 700 Battery is generally 15-20°C (59-68°F) higher than the ambient temperatureduring fast charge. Therefore, to complete a recharge cyc...
Page 125 - Removing the TR 700 Battery
8. Position the TR 700 Battery above the ThinkServer RAID 700 Adapter so that the board-to-board connector 1 on the bottom of the TR 700 Battery is aligned with the connector 2 on the ThinkServer RAID 700 Adapter; and the three mounting studs on the bottom of the TR 700 Battery are aligned withthe c...
Page 126 - Installing or removing the expander card
• Use any documentation that comes with the TR 700 Battery and follow those instructions in addition to the instructions in this topic. To remove the TR 700 Battery, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cor...
Page 127 - Installing the expander card
Notes: • The server must have a RAID card and an expander card installed to support more than eight hard disk drives. • The expander card is sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 86 first and carefully perform the operation. Installing the ...
Page 128 - RAID card before installing the expander card.; Carefully handle the expander card by its edges.
6. There are two PCI Express card slots on the riser card assembly 1 and the shorter one is for installing the expander card. Remove the slot bracket for the shorter slot and store it in case you later remove theexpander card and need the bracket to cover the place. Note: Ensure that you install the...
Page 129 - Removing the expander card; the instructions in this topic.
9. Connect cables depending on your specific server configuration. See “Connecting the cables” on page 47. 10. Reinstall the riser card assembly 1. See “Replacing the riser card assembly 1” on page 176. What to do next: • To work with another piece of hardware, go to the appropriate section. • To co...
Page 130 - expander card” on page 115.; Installing or removing an Ethernet card; devices” on page 86 first and carefully perform the operation.; Installing an Ethernet card
6. There are two PCI Express card slots on the riser card assembly 1 and the expander card is installed in the shorter slot. Disconnect cables from the expander card. Then, grasp the expander card by its edgesand carefully pull it out of the PCI Express card slot. Note: The expander card might fit t...
Page 133 - • If you are using a Windows operating system, run the; Removing an Ethernet card
8. Position the Ethernet card near the PCI Express card slot for which you have removed the slot bracket. Then, carefully press the Ethernet card straight into the slot until it is securely seated and its bracket alsois secured by the riser card assembly 2. Figure 77. Installing an Ethernet card 9. ...
Page 135 - Installing the TR 300 Key
8. If you are instructed to return the old Ethernet card, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to “Com...
Page 136 - Removing the TR 300 Key
6. Insert one side of the TR 300 Key under one of the retaining clips on the iButton socket. Then, carefully press the other side of the TR 300 Key straight down until it snaps into position and is secured by thetwo retaining clips on the iButton socket. Figure 79. Installing the TR 300 Key 7. If yo...
Page 139 - Installing the TMM Premium
Installing or removing the ThinkServer Management Module Premium This topic provides instructions on how to install or remove the ThinkServer Management Module Premium(TMM Premium). The TMM Premium offers convenient, remote KVM access and control through the LAN or Internet. Youcan use the TMM Premi...
Page 140 - refer to the; Removing the TMM Premium
5. Locate the TMM Premium connector on the system board and then insert the TMM Premium into the TMM Premium connector. Note: Ensure that the TMM Premium is securely seated on the system board. Figure 81. Installing the TMM Premium What to do next: • To work with another piece of hardware, go to the...
Page 142 - Installing or removing the ThinkServer Trusted Platform Module; Installing the TPM; This topic provides instructions on how to install the TPM.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to “Completing the parts replacement” on page 199. Installing or removing the ThinkServer Trusted Platform Module This topic provides instructions on how to install or re...
Page 143 - Insert the TPM into the TPM connector on the system board.; Removing the TPM
6. Insert the TPM into the TPM connector on the system board. Figure 83. Installing the TPM 7. If you have lifted the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 176. What to do next: • To work with another piece of hardware, go to the appr...
Page 145 - Carefully handle the TPM by its edges.; Installing or replacing a hot-swap redundant power supply
5. Remove the TPM installed on the TPM connector by lifting it straight up. Note: Carefully handle the TPM by its edges. Figure 84. Removing the TPM 6. If you have lifted the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 176. 7. If you are in...
Page 146 - instructions in addition to the instructions in this topic.
This topic provides instructions on how to install or replace a hot-swap redundant power supply. The hot-swap redundant power supply adds a second source of power to the server. When the server ispopulated with two hot-swap redundant power supplies, it can withstand a power loss from either powersup...
Page 147 - later remove the power supply and need the shield to cover the bay.
• If you are installing a hot-swap redundant power supply, locate the bay for the power supply in the rear of your server. Insert a finger into the hole in the metal shield that protects the bay, press the tab 1 in the direction as shown, and then pull the shield out of the chassis. Store the shield...
Page 148 - it snaps into position.
2. If you are replacing a hot-swap redundant power supply, press the release tab 1 in the direction as shown and carefully pull the handle 2 at the same time to slide the failing hot-swap redundant power supply out of the chassis. Figure 86. Removing a hot-swap redundant power supply 3. Touch the st...
Page 149 - Installing or replacing a heat sink; To install or replace a heat sink, do the following:
5. Connect the power cord to the power cord connector on the new hot-swap redundant power supply. Then, check the status LED near the power cord connector. When the LED is lit in green, it indicatesthat the hot-swap redundant power supply is working correctly. When the LED is lit in amber, it indica...
Page 151 - Installing or replacing the microprocessor; Installing the second microprocessor
10. Install the four screws to secure the new heat sink on the system board. It is recommended that you carefully install the four screws using the following method to avoid any possible damage to the systemboard. a. Partially tighten screw 1 , then firmly tighten screw 3 , and then return to screw ...
Page 153 - be kept as clean as possible.
6. Gently press down the small handle on the microprocessor socket and then pull the handle slightly outward to release it from the secured position. Then, pivot the handle upward to the fully open position.Then, gently press the microprocessor retainer to open it. Figure 90. Opening the small handl...
Page 155 - into position and secure the new microprocessor in the socket.; heat sink” on page 137.; Replacing the microprocessor
11. Carefully close the microprocessor retainer. Then, carefully close the small handle to lock the retainer into position and secure the new microprocessor in the socket. Figure 94. Securing the microprocessor in the socket 12. Install the new heat sink that comes with the microprocessor option kit...
Page 160 - before the installation.
The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. Thenumber of the installed hard disk drives or solid-state drives in your server varies depending on the servermodel. The vacant bays are occupied by dummy hard-disk-drive trays. When you install ...
Page 161 - Press the release button; Do not touch the circuit board on the solid-state drive.
2. Press the release button 1 to open the handle of the dummy hard-disk-drive tray. Figure 100. Opening the handle of the dummy hard-disk-drive tray 3. Pull the handle and carefully slide the dummy hard-disk-drive tray out of the front of the chassis. Figure 101. Removing the dummy hard-disk-drive t...
Page 163 - and then completely close the handle.
8. Align the screw holes in the drive adapter and the solid-state drive with the corresponding holes in the drive bracket. Then, install the five screws to secure the drive adapter and the solid-state drive tothe bracket. Figure 104. Installing the screws to secure the drive adapter and the solid-st...
Page 166 - Lift the solid-state drive up to remove it from the drive adapter.; Installing or replacing the optical drive
5. Remove the two screws that secure the solid-state drive. Figure 109. Removing the screws that secure the solid-state drive 6. Lift the solid-state drive up to remove it from the drive adapter. Figure 110. Removing the solid-state drive from the drive adapter 7. Install a new solid-state drive. Se...
Page 169 - on the side of the new optical drive.
7. Remove the retaining bracket from the old optical drive or the dummy optical drive tray. Then, install it on the side of the new optical drive. Figure 113. Installing the optical drive retaining bracket Chapter 6 . Installing, removing, or replacing hardware 157
Page 171 - Installing an external tape drive
9. Connect the signal cable 1 and the power cable 2 to the rear of the new optical drive. Figure 116. Connecting cables to the rear of the optical drive 10. If you are instructed to return the old optical drive, follow all packaging instructions and use any packaging materials that are supplied to y...
Page 172 - Replacing the PCI Express solid-state drive
2. Connect one end of a mini-SAS signal cable to the mini-SAS connector 1 on the rear of the external tape drive. Figure 117. Mini-SAS connector 1 on the external tape drive 3. Connect the other end of the mini-SAS signal cable to an available mini-SAS connector provided by the Host Bus Adapter inst...
Page 174 - Carefully handle the PCI Express solid-state drive by its edges.
Note: Carefully handle the PCI Express solid-state drive by its edges. 9. Do one of the following: • To install the new PCI Express solid-state drive on the riser card assembly 1, note the dotted lines in the following illustration to help you correctly position the PCI Express solid-state drive nea...
Page 175 - Replacing the ThinkServer RAID Super Capacitor Module
• To install the new PCI Express solid-state drive on the riser card assembly 2, note the dotted lines in the following illustration to help you correctly position the PCI Express solid-state drive near thePCI Express card slot on the riser card assembly 2. Then, carefully press the new PCI Expresss...
Page 178 - Installing or replacing a hot-swap hard disk drive
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 199. Installing or replacing a hot-swap hard disk drive Attention: Do not open your server or attempt any repair before reading an...
Page 182 - • To configure RAID, go to “Configuring RAID” on page 74.
• If you are installing a hot-swap hard disk drive, save the removed hard-disk-drive dummy tray in case you later remove the hot-swap hard disk drive and need a dummy tray to cover the drive bay. • If you are replacing a failing hot-swap hard disk drive and are instructed to return the failing hot-s...
Page 187 - Carefully handle the backplane by its edges.
5. Remove all the installed 2.5-inch hot-swap hard disk drives and dummy trays (if any) from the hard-disk-drive cage (right cage or middle cage). See “Installing or replacing a hot-swap hard diskdrive” on page 166. 6. Record the cable connections on the backplane and then disconnect all cables from...
Page 188 - Replacing the riser card assembly 1; To replace the riser card assembly 1, do the following:
9. Note the orientation of the new backplane. Carefully press the new backplane straight down into the chassis so that it is secured in place by the tabs 1 on the chassis and the three screw holes in the new backplane are aligned with the corresponding holes in the chassis. Then, install the screws ...
Page 190 - card into the chassis and properly route any cables from the card.; any packaging materials that are supplied to you for shipping.; Replacing the riser card assembly 2; To replace the riser card assembly 2, do the following:
11. Position the new riser card assembly 1 on the chassis and align it with the riser card assembly 1 slot on the system board and align the rear of it with the corresponding rail guides in the rear of the chassis.Then, carefully press the new riser card assembly 1 straight down into the chassis unt...
Page 191 - one. See “Installing or removing an Ethernet card” on page 118.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 87. 4. Locate ...
Page 192 - Replacing the front panel board
10. Position the new riser card assembly 2 on the chassis and align it with the riser card assembly 2 slot on the system board and align the rear of it with the corresponding rail guides in the rear of the chassis.Then, carefully press the new riser card assembly 2 straight down into the chassis unt...
Page 196 - Replacing the diagnostic module; This topic contains the following items:
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 199. Replacing the diagnostic module This topic provides instructions on how to replace the diagnostic module. For detailed inform...
Page 199 - Replacing a system fan; This topic provides instructions on how to replace a system fan.
12. Slide the new diagnostic module into the cage from the front until it snaps into position. Figure 151. Installing the diagnostic module into the left cage of server models with 2.5-inch hard-disk-drive bays 13. Connect the diagnostic module cable to the rear of the new diagnostic module. 14. Rei...
Page 201 - Install a new system fan as soon as you remove the failing one.; Replacing the coin-cell battery
5. Position the new system fan above the place for the removed failing system fan so that the system fan connector on the bottom of the new system fan is facing the rear of the chassis. Then, press the newsystem fan straight down until it is seated into place. Note: Install a new system fan as soon ...
Page 202 - reconfigure the server.
DANGER Danger of explosion if battery is incorrectly replaced. When replacing the lithium coin cell battery, use only the same or an equivalent type that isrecommended by the manufacturer. The battery contains lithium and can explode if not properlyused, handled, or disposed of. Do not: • Throw or i...
Page 203 - Replacing the system board
5. Remove the old coin-cell battery. Figure 154. Removing the coin-cell battery 6. Install a new coin-cell battery. Figure 155. Installing the coin-cell battery 7. If you have lifted the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 176. 8. D...
Page 205 - Remove the power supply cooling shroud.
9. Remove the power supply cooling shroud. Figure 157. Removing the power supply cooling shroud 10. Remove all memory modules. See “Removing a memory module” on page 104. 11. Remove the TMM Premium if one is installed. See “Removing the TMM Premium” on page 128. 12. Remove the TPM if one is installe...
Page 206 - board following the recommended numerical sequence as shown.
14. Disconnect all cables from the system board. Then, remove the ten screws that secure the system board following the recommended numerical sequence as shown. Figure 158. Removing the screws that secure the system board 194 ThinkServer RD440 User Guide and Hardware Maintenance Manual
Page 207 - Carefully handle the system board by its edges.
15. Gently lift each edge of the system board slightly upward so that the system board is released from the mounting studs on the chassis. Then, move the system board to the front of the server and thencarefully pivot the system board upward to remove it out of the chassis. Note: Carefully handle th...
Page 208 - system board on the chassis.; “Installing or replacing the microprocessor” on page 139.
18. Install the ten screws following the recommended numerical sequence as shown to secure the new system board on the chassis. Figure 161. Installing the screws to secure the system board 19. Remove the microprocessors from the old system board and install them on the new system board. See “Install...
Page 209 - handle inward to lock the retainer into position.
b. Position the microprocessor socket cover above the microprocessor socket so that the small triangle 1 on the socket cover faces the small triangle 2 on the microprocessor retainer. Then, carefully press the socket cover straight down into the socket until it snaps into position. Figure 162. Insta...
Page 210 - TMM Premium” on page 127.
23. Note the orientation of the power supply cooling shroud and install it into the chassis by inserting the two small tabs 1 on the bottom of the shroud into the corresponding holes 2 in the power supply cage. Figure 164. Installing the power supply cooling shroud 24. Install the coin-cell battery ...
Page 211 - Completing the parts replacement; left inside your server.
30. If you are instructed to return the old system board, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completin...
Page 213 - Pivot the cover latch; Rack Installation
5. Ensure that the cover latch is in the open position. Place the server cover above the chassis so that the cover latch is aligned with the cover latch slot in the chassis. Then, lower the server cover ontothe chassis until the cover latch is inserted into its slot and both sides of the server cove...
Page 214 - Updating the server configuration; • To update the RAID configuration, see “Configuring RAID” on page 74.
Attention: To avoid component damage, connect the power cords last. Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will come with the CRU or will come a few days after the CRU arrives. Updating the server configuration When you turn on the s...
Page 215 - Chapter 7. Troubleshooting and diagnostics; Troubleshooting procedure; functioning electrical outlets.; Viewing the status and diagnostic LEDs
Chapter 7. Troubleshooting and diagnostics This chapter provides information about basic troubleshooting and diagnostic methods to help you solveproblems that might occur in the server. If you cannot diagnose and correct a problem by using the information in this chapter, see Chapter 8“Getting infor...
Page 216 - Using a diagnostic program; Continue; to start the program.; Viewing the system event log; For more information about viewing the SEL, refer to the; Basic troubleshooting tables
Using a diagnostic program The following diagnostic programs are available for you to diagnose server problems: • ThinkServer Diagnostic Tool • ThinkServer System Profile Collection Tool To use a diagnostic program, do the following: 1. Go to http://www.lenovo.com/drivers and follow the instructions...
Page 217 - Optical drive problems; Symptom
Symptom Action The ThinkServer EasyStartup DVD does not start. 1. Ensure that the server supports the ThinkServer EasyStartup program and has a bootable DVD driveinstalled or a bootable external DVD drive attached. 2. Ensure that you have set the optical drive with the ThinkServer EasyStartup DVD in...
Page 219 - Memory module problems
Symptom Action 6. Ensure that the cable connection is correct. See “Connecting the cables” on page 47. 7. Reconnect the backplane power cable and repeat step 1 through step 4. 8. Reconnect the backplane signal cable and repeat step 1 through step 4. 9. If you suspect a problem with the backplane sig...
Page 221 - ThinkServer Web site; • Purchase additional services and software.; Lenovo Support Web site; • Drivers and software
Chapter 8. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufacturedby Lenovo and where to go for additional information about Lenovo and Lenovo products. Information resources You can use the information in this ...
Page 222 - Problem determination
• Diagnostic solutions • Product and service warranty • Product and parts details • User guides and manuals • Knowledge base and frequently asked questions Help and service This topic contains information about obtaining help and service. Before you call Before you call, do the following to try to s...
Page 223 - Using other services; Warranty; the instructions on the screen.; Purchasing additional services
For the warranty type and duration for your product, refer to the Safety, Warranty, and Support Information on the documentation DVD that comes with your server. You must retain your proof of purchase to obtainwarranty service. For warranty service, consult the worldwide Lenovo Support telephone lis...
Page 226 - Trademarks; Linux is a registered trademark of Linus Torvalds.; Important notes; Wash hands after handling; Recycling information
Trademarks Lenovo, the Lenovo logo, and ThinkServer are trademarks of Lenovo in the United States, other countries, orboth. Intel and Intel Xeon are trademarks of Intel Corporation in the United States, other countries, or both. Internet Explorer, Microsoft, Windows, and Windows Server are trademark...
Page 227 - Battery return program; Battery recycling information for the United States and Canada; This mark applies only to countries within the European Union (EU).; Requirement for batteries containing perchlorate; California Perchlorate Information:
Battery return program This product may contain a lithium or lithium ion battery. Consult your user manual or service manual forspecific battery information. The battery must be recycled or disposed of properly. Recycling facilities maynot be available in your area. For information on disposal or ba...
Page 228 - Particulate contamination; Contaminant; Important WEEE information
Perchlorate Material - special handling may apply, Seehttp://www.dtsc.ca.gov/hazardouswaste/perchlorate Particulate contamination Attention: Airborne particulates (including metal flakes or particles) and reactive gases acting alone or in combination with other environmental factors such as humidity...
Page 230 - Industry Canada Class A emission compliance statement; This Class A digital apparatus complies with Canadian ICES-003.; United Kingdom telecommunications safety requirement; Notice to Customers; German Class A compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation. Industry Canada Class A em...
Page 231 - ENERGY STAR
Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Betriebsmittein Dieses Produkt entspricht dem „Gesetz über die elektromagnetische Verträglichkeit von Betriebsmitteln“EMVG (früher „Gesetz über die elektromagnetische Verträglichkeit von Geräten“). Dies ist die Umsetzung derEU-R...
Page 233 - Index
Index A about RAID 75 Advanced menu Setup Utility program 64 advanced SATA/SAS hardware RAID configuring 82 ambient temperature limit LED 25, 28 B BIOS and TMM update utilities software 13 BMC status LED 60 Boot Manager menu Setup Utility program 66 Boot Options menu Setup Utility program 66 C cable...