Lenovo RS210- Manual

Chapter 1. About this manual This Hardware Maintenance Manual contains information to help you solve problems that might occur in your server. It describes the diagnostic tools that come with the server, error codes and suggested actions,and instructions for replacing failing components. Replaceable...

Safety statements Important: Each caution and danger statement in this document is labeled with a number. This number is used tocross reference an English-language caution or danger statement with translated versions of the cautionor danger statement in the Safety Information document. For example, ...

Statement 3: CAUTION:When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) areinstalled, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure tohazardous laser radiation. There are no serviceable parts ins...

Statement 8: CAUTION:Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this labelattached. There are no serviceable parts inside these components. If you suspect a proble...

RoHS compliant ThinkServer RS210 parts have unique FRU part numbers. Before or after June, 2006,failed RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUsidentified as compliant in the system Hardware Maintenance Manual or direct substitutions for thoseFRUs can b...

Chapter 2. General information This chapter provides general information that applies to all machine types supported by this publication. Features and technologies The server uses the following features and technologies: v UEFI-compliant server firmware UEFI replaces the basic input/output system (B...

– Event logs for RAID controllers and service processorsThe diagnostics programs create a merged log that includes events from all collected logs. Theinformation is collected into a file that you can send to the Lenovo technical support team to helpdiagnose a problem. Additionally, you can view the ...

Table 1. Features and specifications (continued) RAID controllers: v An IBM ServeRAID-BR10il SAS/SATAController that provides RAID levels 0,1, and 1E (comes standard on somehot-swap SAS and hot-swap SATAmodels). v An optional IBM ServeRAID-MR10iSAS/SATA Controller SAS/SATAadapter that provides RAID ...

EasyManage The ThinkServer EasyManage Core server provides centralized hardware and software inventorymanagement and secure automated system management through a centralized console. The ThinkServerEasyManage Agent enables other clients on the network to be managed by the centralized console. TheThi...

Chapter 3. General Checkout You can solve many problems without outside assistance by following the troubleshooting procedures inthis Hardware Maintenance Manual and on the Lenovo Web site. This document describes the diagnostic tests that you can perform, troubleshooting procedures, and explanation...

Performing the checkout procedure To perform the checkout procedure, complete the following steps: 1. Is the server part of a cluster? v No: Go to step 2. v Yes: Shut down all failing servers that are related to the cluster. Go to step 2. 2. Complete the following steps: a. Check the power supply LE...

Lenovo service bulletins document known problems and suggested solutions. To search for servicebulletins, complete the following steps. 1) Go to: http://www.lenovo.com/support. 2) From the Select your product list, select Servers and Storage . 3) In the Browse by product window Family: list, select ...

Chapter 4. Diagnostics This chapter describes the diagnostic tools that are available to help you solve problems that might occurin the server. Diagnostic tools The following tools are available to help you diagnose and solve hardware-related problems: v POST error messages and error logs The power-...

v System-event log: This log contains messages that were generated during POST and all system status messages from the service processor. You can view the contents of the system-event log from the Setuputility for more information.The system-event log is limited in size. When it is full, new entries...

Table 2. Methods for viewing event logs (continued) Condition Action The server is hung. v If DSA Preboot is installed, restart the server and pressF2 to start DSA Preboot and view the event logs. v If DSA Preboot is not installed, insert the DSA PrebootCD and restart the server to start DSA Preboot...

v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which components are field...

Integrated management module error messages The following table describes the IMM error messages and suggested actions to correct the detectedproblems. v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listin...

Troubleshooting tables Use the troubleshooting tables to find solutions to problems that have identifiable symptoms. If you have just added new software or a new optional device and the server is not working, do thefollowing before using the troubleshooting tables: 1. Check the system-error LED on t...

DVD drive problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which c...

General problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which com...

v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which components are field...

Intermittent problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and whic...

Memory problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which comp...

Microprocessor problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and wh...

Monitor problems Some monitors have their own self-tests. If you suspect a problem with your monitor, see thedocumentation that comes with the monitor for instructions for testing and adjusting the monitor. If youcannot diagnose the problem, call for service. v Follow the suggested actions in the or...

Optional-device problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and w...

Power problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which compo...

v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which components are field...

v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which components are field...

Universal Serial Bus (USB) port problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable u...

v Follow the suggested actions in the order in which they are listed in the Action column until the problem issolved. v See Chapter 7, “Parts listing, RS210 Types 6531, 6532, 6533, and 6534,” on page 177 to determine whichcomponents are customer replaceable units (CRU) and which components are field...

Table 4. System pulse LEDs LED Description Action Enclosure manager heartbeat power-on and power-off sequencing. 1. If the LED flashes at 1Hz, it isfunctioning properly and noaction is necessary. 2. If the LED is not flashing, (trainedservice technician only) replacethe system board. IMM heartbeat I...

Diagnostic messages The following table describes the messages that the diagnostic programs might generate and suggestedactions to correct the detected problems. Follow the suggested actions in the order in which they arelisted in the column. Table 5. DSA Preboot messages v Follow the suggested acti...

Recovering the server firmware Important: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution beforeyou update the code. If the server firmware has bec...

Boot blockjumper (JP6) Clear CMOSjumper (JP1) 4. Move the jumper from pins 1 and 2 to pins 2 and 3 to enable the UEFI recovery mode. 5. Reinstall the server cover; then, reconnect all power cords. 6. Restart the server. The power-on self-test (POST) starts. 7. Boot the server to an operating system ...

Automated boot recovery (ABR) If the server is booting up and the IMM detect problems with the server firmware in the primary bank, itwill automatically switch to the backup firmware bank and give you the opportunity to recover theprimary bank. To recover to the server firmware primary bank, complet...

– If you directly connect two servers (without a hub), or if you are not using a hub with X ports, use a crossover cable. To determine whether a hub has an X port, check the port label. If the labelcontains an X, the hub has an X port. v Determine whether the hub supports auto-negotiation. If it doe...

Problem determination tips Because of the variety of hardware and software combinations that can encounter, use the followinginformation to assist you in problem determination. If possible, have this information available whenrequesting assistance from Lenovo. The model number and serial number of t...

Chapter 5. Locating Server Controls and connectors This section describes the controls, light-emitting diodes (LEDs), and connectors on the front and rear ofthe server, and how to turn the server on and off. For the location of the LEDs on the system board, see“System-board LEDs” on page 112. Note: ...

Rear view 1 Power-cord connector 9 NMI button 2 Serial connector 10 USB 3-4 connector 3 Ethernet 1 activity LED 11 USB 1-2 connector 4 Ethernet 1 link LED 12 Video connector 5 Ethernet 2 activity LED 13 Power supply error LED (amber) 6 Ethernet 2 link LED 14 DC power LED (green) 7 PCI slot 1 15 AC p...

System-board internal connectors The following illustration shows the internal connectors on the system board. Microprocessor Heatsink Orientation DIMMs DIMMs 1 DIMM 1 11 Fan 1 connector 21 Riser-card connector 2 2 DIMM 2 12 Hard disk backplane configurationconnector 22 Riser-card connector 1 3 DIMM...

System-board external connectors The following illustration shows the external connectors on the system-board. Microprocessor Heatsink Orientation DIMMs DIMMs 1 Serial (com 1) connector 5 Ethernet connector 2 2 Video connector 6 USB connectors 3 and 4 3 Ethernet connector 1 7 SW1 (NMI button) 4 USB ...

System-board switches and jumpers The following illustration shows the switches and jumpers on the system board. Microprocessor Heatsink Orientation DIMMs DIMMs The following table describes the jumpers on the system board. Table 6. System board jumpers Jumper number Jumper name Jumper setting JP1 C...

Server power features When the server is connected to an ac power source but is not turned on, the operating system does notrun, and all core logic except for the service processor (the integrated management module) is shut down;however, the server can respond to requests to the service processor, s...

Chapter 6. Replacing FRUs Guidelines for trained service technicians This section contains information for trained service technicians. Inspecting for unsafe conditions Use the information in this section to help you identify potential unsafe conditions in a Lenovo productthat you are working on. Ea...

v Do not touch the reflective surface of a dental mirror to a live electrical circuit. The surface isconductive and can cause personal injury or equipment damage if it touches a live electrical circuit. v Some rubber floor mats contain small conductive fibers to decrease electrostatic discharge. Do ...

Handling static-sensitive devices Attention: Static electricity can damage the server and other electronic devices. To avoid damage, keep static-sensitive devices in their static-protective packages until you are ready to install them. To reduce the possibility of damage from electrostatic discharge...

Major components of the server The following illustrations show the major components in the server. The illustrations in this documentmight differ slightly from your hardware. 1 Riser card assembly 12 Bezel 2 DIMM air baffle 13 DVD drive filler 3 DIMM 14 Operator information panel 4 Power supply 15 ...

Removing and installing the cover Use the following procedures to remove and install the cover: Removing the cover To remove the server cover, do the following: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trainedservice technicians” on page 115. 2. ...

Removing and installing the bezel To remove the bezel, complete the following steps: 1. Remove the server from the rack and remove the cover (see “Removing and installing the cover” onpage 119). 2. From inside the server, press the bezel release latch 1 toward the left side of the server. 3. Pivot t...

Replacing a memory module (DIMM) To replace a dual inline memory module (DIMM), use the following information and procedures: Supported memory types Following is information that describes the types of dual inline memory modules (DIMMs) that theserver supports and other information that you must con...

v The following table lists the supported RDIMM population. Table 11. Supported RDIMM population per channel DIMM connectorsper channel DIMMs installed ineach channel DIMM type DIMM speed Ranks per DIMM(any combination) 3 1 Registered DDR3ECC 1066, 1333 Single-rank,dual-rank 3 2 Registered DDR3ECC 1...

Attention: To ensure proper cooling and airflow, do not operate the server for more than 30 minutes with the cover removed. 4. Remove the DIMM air baffle (see “Removing and installing the DIMM air baffle” on page 121). 5. Carefully open the retaining clips 2 on each end of the DIMM connector and rem...

6. Touch the static-protective package that contains the DIMM to any unpainted metal surface on theoutside of the server. Then, remove the DIMM from the package. 7. Turn the DIMM 1 so that the DIMM keys align correctly with the connector (see “System-board internal connectors” on page 107 for the lo...

6. Release the loops of the drive tray. 7. Insert the filler panel into the bay to cover the drive. Note: If the server is configured for RAID operation using a RAID controller, you might have to reconfigure your disk arrays after you install hard disk drives. See the RAID controller documentationfo...

3. Grasp the handle and pull the hot-swap drive assembly 2 out of the drive bay. Installing a hot-swap hard disk drive To install a hot-swap hard disk drive, complete the following steps. Note: If your server has only one hot-swap hard disk drive, install it in the left or upper-left drive bay. Atte...

Installing a PCI card To install a PCI card, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trainedservice technicians” on page 115. 2. Turn off the server and peripheral devices and disconnect the power cords and all exte...

6. Follow the instructions that come with the PCI card to set any jumpers or switches. Attention: When you install an PCI card, make sure that it is completely and correctly seated in the expansion slot in the riser card. Incomplete insertion might cause damage to the riser card, systemboard, or the...

2. Turn off the server and peripheral devices and disconnect the power cords. 3. Remove the cover (see “Removing and installing the cover” on page 119). 4. Remove the riser-card assembly (see “Removing the riser-card assembly” on page 157). 5. Unlock the retention latch on the USB connector by squee...

6. Lift the operator information panel assembly out of the server. 7. If you are instructed to return the operator information panel assembly, follow all packaginginstructions, and use any packaging materials for shipping that are supplied to you. Installing the operator information panel assembly T...

Replacing the drive cage To replace the drive cage, use the following procedures: Removing the drive cage The following illustration shows removing a simple-swap 3.5-inch drive cage. The following illustration shows removing a hot-swap 3.5-inch drive cage. The following illustration shows removing a...

Installing the drive cage The following illustration shows installing a simple-swap 3.5-inch drive cage. The following illustration shows installing a hot-swap 3.5-inch drive cage. The following illustration shows installing a hot-swap 2.5-inch drive cage. 138 ThinkServer ThinkServer RS210, Types 65...

To install a drive cage, complete the following steps: 1. Make sure that the backplane or back plate is removed from the drive cage. (See “Removing thebackplane or back plate (3.5-inch drives)” on page 154 or “Removing the SAS backplane (2.5-inchdrives)” on page 156 for instructions, as applicable.)...

http://www.lenovo.com/support. v The microprocessor uses an integrated voltage regulator on the system board. Removing the microprocessor To remove the microprocessor, complete the following steps. 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained...

9. Remove the microprocessor: a. Carefully lift the microprocessor 1 straight up and out of the socket, without touching the microprocessor contacts. b. Place the microprocessor on a static-protective surface 10. If you are instructed to return the microprocessor, follow all packaging instructions, ...

6. Go to “Completing the FRU replacement” on page 173. Thermal grease The thermal grease must be replaced whenever the heat sink has been removed from the top of themicroprocessor and is going to be reused or when debris is found in the grease. When you are installing the heat sink on the same micro...

8. Remove the memory modules and set them aside on a static-protective surface for reinstallation (see“Replacing a memory module (DIMM)” on page 122). Note: Make a note of the location of each DIMM as you remove it, so that you can later reinstall it in the same connector. 9. Remove the virtual medi...

“Updating the firmware” on page 212“Updating the Universal Unique Identifier (UUID)” on page169“Updating the DMI/SMBIOS data” on page 171 for more information. Important: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, ver...

1 2 Statement 8: CAUTION:Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this labelattached. There are no serviceable parts inside these components. If you suspect a pr...

7. Loosen the captive thumbscrew 3 that secures the power supply to the chassis bottom. 8. Lift the power supply out of the bay. 9. If you are instructed to return the power supply, follow all packaging instructions, and use anypackaging materials for shipping that are supplied to you. Installing th...

Table 14. Removing the fan 1 Fan 1 4 Fan 4 2 Fan 2 5 Fan 5 3 Fan 3 9. If you are instructed to return the fan, follow all packaging instructions, and use any packagingmaterials for shipping that are supplied to you. Installing a fan assembly To install the replacement fan, complete the following ste...

Microprocessor Heatsink Orientation DIMMs DIMMs a. Use a fingernail to press the top of the battery clip away from the battery. The battery pops upwhen released. b. Use your thumb and index finger to lift the battery from the socket. 6. Dispose of the battery as required by local ordinances or regul...

v Set the power-on password. v Reconfigure the server. Replacing the SAS/SATA hard disk drive back plate or backplane To replace the SAS/SATA hard disk drive backplane or back plate, complete the following procedures: Removing the backplane or back plate (3.5-inch drives) To remove the Serial Attach...

Installing the SAS backplane (2.5-inch drives) To install the replacement 2.5-inch hot-swap drives backplane, complete the following steps. 1 Alignment tabs 3 Alignment slots 2 Drive connectors 4 Drive connectors 1. Connect the cables to the replacement backplane. 2. Slide the backplane into the car...

6. If the riser-card assembly is an optional PCI-X riser-card assembly, disconnect the riser-card powercable 1 from the riser-card assembly. 7. Disconnect any cables from the PCI cards in the riser-card assembly. 8. If you are instructed to return the riser-card assembly, follow all packaging instru...

5. Carefully align the riser-card assembly with the guides on the rear of the server and with theriser-card connectors on the system board; then, press down on the assembly. Make sure that theriser-card assembly 1 is fully seated in the connector on the system board. 6. Go to “Completing the FRU rep...

6. Disconnect the signal cables that are attached to the SAS/SATA controller. 7. Grasp the SAS/SATA controller 1 while you press outward on the plastic tabs. 8. Pull out the SAS/SATA controller from the connector 2 on the system board. 9. If you are instructed to return the SAS/SATA controller, foll...

7. Remove the cable from the DVD drive cage connector. 8. Disconnect the DVD drive power cable from the power supply cable. 9. If you are instructed to return the DVD drive cable, follow all packaging instructions, and use anypackaging materials for shipping that are supplied to you. Installing the ...

5. Remove the retention clip 1 from the drive and save for future use. 6. If you are instructed to return the DVD drive, follow all packaging instructions, and use anypackaging materials for shipping that are supplied to you. Installing a DVD drive The following notes describe the type of drives tha...

Replacing the virtual media key To replace the virtual media key, complete the following procedures: Removing the virtual media key To remove the virtual media key, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trainedser...

Microprocessor Heatsink Orientation DIMMs DIMMs 4. Go to “Completing the FRU replacement” on page 173. Replacing the PCI-X riser-card power cable To replace the PCI-X riser-card power cable, use the following procedures: Removing the PCI-X riser-card power cable If an optional PCI-X riser-card assem...

7. Disconnect the riser-card power cable from the PCI-X riser card. 8. If you are instructed to return the PCI-X riser-card power cable, follow all packaging instructions, anduse any packaging materials for shipping that are supplied to you. Installing the PCI-X riser-card power cable To install the...

e. Click User’s guides and manuals to link to the ASU Users Guide. v Remote LAN access, type the command: Note: When using the remote LAN access method to access IMM using the LAN from a client, the host and the imm_external_ip address are required parameters. host <imm_external_ip> [user <...

a. Go to http://www.lenovo.com/support. b. Enter your product number (machine type and model number) or select Servers and Storage from the Select your product list. c. From Family list, select ThinkServer RS210; , and click Continue . d. Click Downloads and drivers . e. Click User’s guides and manu...

5. Update the server configuration (see “Updating the server configuration” on page 175). 6. Slide the server back into the rack, if necessary. 7. Turn on the peripheral devices and the server. Connecting the cables The following illustration shows the locations of the input and output connectors on...

The following illustration shows the connectors and LEDs on the rear of the server. 1 Power-cord connector 9 NMI button 2 Serial connector 10 USB 3-4 connector 3 Ethernet 1 activity LED 11 USB 1-2 connector 4 Ethernet 1 link LED 12 Video connector 5 Ethernet 2 activity LED 13 Power supply error LED ...

Chapter 7. Parts listing, RS210 Types 6531, 6532, 6533, and6534 The following replaceable components are available for the ThinkServer RS210 Types 6531, 6532, 6533,and 6534 servers. To check for an updated parts listing on the Web, complete the following steps: 1. Go to http://www.lenovo.com/support...

Replaceable server components Replaceable components are of three types: v Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility. If Lenovo installs a self-service CRU at your request, you will be charged for the installation. v Optional-service custom...

6534 Software FRU FRU# WS 2008 R2 STD 64bit GR (models CTO All Models) 90Y1185 WS 2008 R2 STD 64bit JP (models CTO All Models) 90Y1186 WS 2008 R2 STD 64bit SP (models CTO All Models) 90Y1187 WS 2008 R2 STD 64bit IT (models CTO All Models) 90Y1188 WS 2008 R2 STD 64bit TR (models CTO All Models) 90Y11...

Select this choice to save the changes that you have made in the settings. v Restore Settings Select this choice to cancel the changes that you have made in the settings and restore the previoussettings. v Load Default Settings Select this choice to cancel the changes that you have made in the setti...

Table 23. System board jumpers (continued) Jumper number Jumper name Jumper setting Notes: 1. If no jumper is present, the server responds as if the pins are set to 1 and 2. 2. Changing the position of the UEFI boot recovery jumper from pins 1 and 2 to pins 2 and 3 before the server isturned on alte...

Table 24. RAID configuration utilities (continued) RAID configuration utility Description Location Where to find moreinformation MegaRAID BIOSConfiguration Utility(WebBIOS) For: v IBM ServeRAID-BR10ilSAS/SATA Controller v IBM ServeRAID-MR10iSAS/SATA Controller v IBM ServeRAID-M1015SAS/SATA controlle...

Attention: If you select Clear Configuration or New Configuration , all existing data in the configuration is deleted. Make a backup copy of any data that you want to keep before selecting theseoptions. Clear Configuration Clears the existing configuration. New Configuration Clears the existing conf...

The EasyStartup program has the following features: v Self-booting DVD v Easy-to-use, language-selectable interface v Integrated help system v Automatic hardware detection v RAID configuration utility v Device drivers (based on the server model and detected devices) v Selectable partition size and f...

Note: The following language keyboards are supported: English, Dutch, French, German, Italian, Japanese, Spanish, and Turkish. You will then see one or more reminders about configuring storage devices, and then you will bepresented with the Lenovo License Agreement. Read the license agreement carefu...

The following items are downloadable at http://www.lenovo.com/support: v Diagnostics programs v IMM firmware v Ethernet firmware Using the EasyUpdate Firmware Updater tool ThinkServer EasyUpdate Firmware Updater is a software application that enables you to maintain yoursystem firmware up to date an...

Using the integrated management module The integrated management module (IMM) is a second generation of the functions that were formerlyprovided by the baseboard management controller hardware. It combines service processor functions,video controller, and (when an optional virtual media key is insta...

IBM Advanced Settings Utility program The IBM Advanced Settings Utility (ASU) program is an alternative to the UEFI Setup Utility program formodifying UEFI settings. Use the ASU program online or out of band to modify UEFI settings from thecommand line without the need to restart the system to acces...

4. Download Microsoft Web Services Enhancement 2.0 Service Pack 3 (LANDesk Process Manager only)from the following Web site: http://www.microsoft.com/downloads/details.aspx?FamilyID=1ba1f631-c3e7-420a-bc1e-ef18bab66122&DisplayLang=en. Install the software using the default settings. Note: This s...

Uninstalling the LANDesk Software Agent If the Core Server has LANDesk agents on it from a previous Management Suite release, it will fail theautorun prerequisite check. You must remove the old agents by running uninstallwinclient.exe file fromthe \Program Files\LANDesk\ManagementSuite folder. Using...

Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: LenovoLenovo logoThinkServer The following terms are trademarks of International Business Machines Corporation in the United States,other countries, or both: IBM ® ServeRAID ™ Intel and Intel Xeon...

Product recycling and disposal This unit must be recycled or discarded according to applicable local and national regulations. Lenovoencourages owners of information technology (IT) equipment to responsibly recycle their equipmentwhen it is no longer needed. Lenovo offers a variety of programs and s...

Compliance with Republic of Turkey Directive on the Restriction ofHazardous Substances Meets requirements of the Republic of Turkey Directive on the Restriction of the Use of CertainHazardous Substances In Electrical and Electronic Equipment (EEE). Türkiye EEE Yönetmeliğine Uygunluk Beyanı T.C. Çevr...

Battery return program This product may contain a lithium or lithium ion battery. Consult your user manual or service manualfor specific battery information. The battery must be recycled or disposed of properly. Recycling facilitiesmay not be available in your area. For information on disposal or ba...

United Kingdom telecommunications safety requirement Notice to Customers This apparatus is approved under approval number NS/G/1234/J/100003 for indirect connection topublic telecommunication systems in the United Kingdom. European Union EMC Directive conformance statement This product is in conform...

Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4: Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A. Nach der EN 55022: “Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im WohnbereichFunkstörungen verursachen; in diesem Fall kann vom Betreiber verlangt ...

Index A ABR, automatic boot failure recovery 102 acoustical noise emissions 12administrator password 202air deflector important note 147location 147 ASM event log 20assertion event, system-event log 20automatic boot failure recovery (ABR) 102 B backup firmware starting 213 battery removing 151, 152r...