Page 5 - Contents; iii
Contents Chapter 1. About this manual . . . . . . 1 Important Safety Information . . . . . . . . . . 1 Chapter 2. Safety information . . . . . . 3 General safety . . . . . . . . . . . . . . . . 3 Electrical safety . . . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . . 5 Hand...
Page 6 - iv
Page 7 - Chapter 1. About this manual; Important Safety Information
Chapter 1. About this manual This manual contains service and reference information for IdeaCentre K430 & K410 computers listed on thecover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Inf...
Page 9 - Chapter 2. Safety information; General safety
Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer. General safety Follow these rules to ensure general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting a...
Page 12 - Grounding requirements; DANGER
• Avoid contact with other people while handling the part. • Wear a grounded wrist strap against your skin to eliminate static on your body. • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. • Use the black side ...
Page 13 - • Throw or immerse into water
To Connect To Disconnect 1. Turn everything OFF. 2. First, attach all cables to devices. 3. Attach signal cables to connectors. 4. Attach power cords to outlet. 5. Turn device ON. 1. Turn everything OFF. 2. First, remove power cords from outlet. 3. Remove signal cables from connectors. 4. Remove all...
Page 15 - Chapter 3. General information; Specifications
Chapter 3. General information This chapter provides general information that applies to all machine types supported by this publication. Specifications This section lists the physical specifications for your computer. This section lists the physical specifications for your computer. Type IdeaCentre...
Page 17 - Chapter 4. General Checkout
Chapter 4. General Checkout Attention: The drives in the computer you are servicing might have been rearranged or the drive startup sequence changed. Be extremely careful during write operations such as copying, saving, or formatting.Data or programs can be overwritten if you select an incorrect dri...
Page 19 - Chapter 5. Using the Setup Utility; Password considerations
Chapter 5. Using the Setup Utility The Setup Utility program is used to view and change the configuration settings of your computer, regardlessof which operating system you are using. However, the operating-system settings might override any similarsettings in the Setup Utility program. Starting the...
Page 21 - Enabling or disabling a device
To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key. 3. The password dialog box will be displayed. Type the pass...
Page 22 - Selecting a startup device
USB Setup press the Enter key, and then select USB Functions . ATA Device Setup press the Enter key. Select Configure SATA as , press the Enter key and then select SATA mode. Audio Setup press the Enter key, and then select Onboard Audio Controller . Network Setup press the Enter key, then select On...
Page 23 - Exiting the Lenovo BIOS Setup Utility program
b. If you have changed these settings and want to return to the default settings, select Load Optimal Defaults from the menu. Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. Y...
Page 25 - Hard disk drive boot error; Power Supply Problems
Chapter 6. Symptom-to-FRU Index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first.Always begin with Chapter 4, “General Checkout,” on page 11. This index can also be used to help youdecide which FRUs to have available when servicing a computer. ...
Page 26 - POST error codes; Undetermined problems
POST error codes Each time you turn the computer on, it performs a series of tests to check that the system is operatingcorrectly and that certain options are set. This series of tests is called the Power-On Self-Test , or POST . POST does the following: • Checks some basic system-board operations •...
Page 31 - Chapter 8. Replacing hardware; General information; Pre-disassembly instructions
Chapter 8. Replacing hardware Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at:ht...
Page 32 - Replacing the keyboard and mouse; To replace the keyboard:; Removing the computer cover; To remove the computer cover:
Replacing the keyboard and mouse Note: Your keyboard will be connected to a USB connector at either front or at the rear of the computer. To replace the keyboard: Step 1. Remove any media (disks, CDs, or memory cards) from the drives, shut down the computer, andturn off all attached devices. Step 2....
Page 33 - Removing the front bezel; To remove the front bezel:
Step 5. Slide the computer cover out to remove it. Step 6. To reinstall the computer cover: a. Line up the computer cover with the chassis then slide it back. b. Secure the computer cover to the chassis with the screws. Removing the front bezel Note: For this procedure, it helps to lay the computer ...
Page 34 - Replacing a memory module; To replace a memory module:
Step 2. Remove the front bezel by releasing the three plastic tabs inside the chassis and sliding the bezelout as shown. Step 3. To reattach the bezel, align the plastic tabs on the bottom of the bezel with the corresponding holesin the chassis, and then snap it into position. Replacing a memory mod...
Page 35 - Replacing a hard disk drive; To replace a hard disk drive:
Step 4. Position the new memory module over the memory connector. Make sure that the notch 1 on the memory module aligns correctly with the connector key 2 on the system board. Push the memory module straight down into the connector until the retaining clips close. Step 5. Reattach the computer cove...
Page 36 - Replacing an optical drive; To replace an optical drive:
Step 4. Remove the hard disk drive from the plastic bracket as shown. Step 5. Line up the new hard disk drive with the plastic bracket and snap it into position. Step 6. Slide the new hard disk drive into the drive bay and slide the drive bay into place. Step 7. Connect the power and signal cables t...
Page 37 - Replacing a graphics card; To replace a graphics card:
Replacing a graphics card Note: For this procedure, it helps to lay the computer flat. To replace a graphics card: Step 1. Remove the computer cover. Refer to “Removing the computer cover”. Step 2. Follow the below steps to remove a graphics card: If your computer has a Duo-graphics cards installed,...
Page 39 - Replacing the TV-Tuner card
a. Remove the screw that secures the graphics latch to the chassis and open it. 1 2 3 b. Remove the graphics card by pulling it straight out of the connector. Step 3. Install the new adapter into the same adapter connector. Step 4. Turn the graphics card latch to the closed position and secure it wi...
Page 42 - Replacing the heat-sink
Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operatingsystem, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, ...
Page 43 - Replacing the CPU
Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O)cables, and any other cables that are connected to the computer. Refer to “Left and right view”and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer ...
Page 45 - Replacing the Wi-Fi card
Step 8. Holding the sides of the microprocessor with your fingers, remove the protective cover 1 that protects the gold contacts on the new microprocessor. 2 Step 9. Holding the sides of the microprocessor with your fingers, position the microprocessor so that thenotches on the microprocessor are al...
Page 46 - Replacing the motherboard
To replace the Wi-Fi card: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operatingsystem, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. ...
Page 47 - FRU lists
Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O)cables, and any other cables that are connected to the computer. Refer to “Left and right view”and “Rear view” for help with locating the vario...
Page 57 - Chapter 9. General information; Additional Service Information; Power management
Chapter 9. General information This chapter provides general information that applies to all machine types supported by this publication. Additional Service Information This chapter provides additional information that the service representative might find helpful. Power management Power management ...
