Lenovo 7567 - Manual

Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer. General safety Follow these rules to ensure general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting a...

• Wear a grounded wrist strap against your skin to eliminate static on your body. • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. • Use the black side of a grounded work mat to provide a static-free work surfac...

• When possible, use one hand only to connect or disconnect signal cables. • Never turn on any equipment when there is evidence of fire, water, or structural damage. • Disconnect the attached power cords, telecommunications systems, networks, and modemsbefore you open the device covers, unless instr...

≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) 1 2 PERIGO 10 ThinkCentre Edge Hardware Maintenance Manual

• Não remova as tampas. A remoção das tampas de um produto a laser pode resultar em exposição prejudicial à radiação de laser. Não existem peças que podem ser consertadas no interior do dispositivo. • A utilização de controles ou ajustes ou a execução de procedimentos diferentes dos especificados aq...

1 2 DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenterun danger. Pour éviter tout risque de choc électrique : • Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au...

Connexion Déconnexion 1. Mettez les unités HORS TENSION. 2. Commencez par brancher tous les cordons sur les unités. 3. Branchez les câbles d'interface sur des connecteurs. 4. Branchez les cordons d'alimentation sur des prises. 5. Mettez les unités SOUS TENSION. 1. Mettez les unités HORS TENSION. 2. ...

• Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerkenund Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- undKonfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind. • Zum Installieren, Transportieren und Öff...

Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegelverwenden. Strahlungsbereich meiden. ≥18 kg ≥32 kg ≥55 kg ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromv...

• Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale. • Non accendere assolutamente apparecchiature in presenza di incendi, perdite d'acqua o dannostrutturale. • Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima diaprire i c...

• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y losmódems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique locontrario en los procedimientos de instalación y configuración. • Conecte y desconecte los cables, como se describe...

Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta losiguiente: Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera coninstrumentos ópticos, y evite exponerse directamente al rayo láser. ≥18 kg ≥32 kg ≥55 kg...

Chapter 3. General information This chapter provides general information that applies to all machine types supported by this publication. Lenovo ThinkVantage Tools The Lenovo ThinkVantage ® Tools program guides you to a host of information sources and provides easy access to various tools to help yo...

• Troubleshooting information • Parts information • Downloads and drivers • Links to other useful sources of information To access this information, go to:http://www.lenovo.com/support Specifications This section lists the physical specifications for your computer. Dimensions Width: 406 mm (15.98 in...

Chapter 4. General Checkout Attention The drives in the computer you are servicing might have been rearranged or the drive startup sequencechanged. Be extremely careful during write operations such as copying, saving, or formatting. Data orprograms can be overwritten if you select an incorrect drive...

Chapter 5. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If your computer problem isnot described here, see “Diagnostics” on page 49 for additional troubleshooting resources. Basic troubleshooting The following table provides information t...

Symptom Action The wireless keyboard or mousedoes not work. Verify that: • The computer is turned on. • The battery or batteries installed in the wireless keyboard or mouse are in good condition. • The wireless configurations are all set correctly. You might need to refer to the documentation that c...

Troubleshooting Use the troubleshooting information to find solutions to problems that have definite symptoms. If the symptom your computer is experiencing occurred immediately after a new hardware option or newsoftware installed, do the following before referring to the troubleshooting information:...

• Some models have a front audio panel you can use to adjust volume. If you have a front audio panel, verify that the volume is not set too low. • Verify that your external speakers (and headphones, if used) are connected to the correct audio connector on the computer. Most speaker cables are color-...

• “A CD or DVD does not work” on page 37 • “Unable to use a startable (bootable) recovery medium, such as the Product Recovery CD, to start your computer” on page 37 An audio disc or AutoPlay-enabled disc does not automatically play when it isinserted into a CD drive Symptom: An audio disc or AutoPl...

• Ensure that a DVD disc is in the drive with the shiny side of the disc facing down. • Ensure that video resolution is set to less than 1152 x 864. • On computers that have a CD-ROM or CD-RW drive in addition to a DVD-ROM drive, make sure that the DVD disc is in the drive labeled “DVD”. If these ac...

Monitor problems Note: Many monitors have status-indicator lights and built-in controls for adjusting brightness, contrast, width, height, and other picture adjustments. However, the controls vary from monitor type to monitor type. Select your symptom from the following list: • “Wrong characters app...

problem. Move fluorescent desk lighting or any equipment that produces magnetic fields farther awayfrom the monitor. If this does not correct the problem, do the following: 1. Turn off the monitor. (Moving a color monitor while it is turned on might cause screen discoloration.) 2. Adjust the placeme...

4. Select the Playback tab. 5. If you are using Headset profile, select Bluetooth Hands-free Audio and click the Set Default button. If you are using AV profile, select Stereo Audio and click the Set Default button. 6. Click OK to close the Sound window. PIM items sent from the Windows 7 operating s...

• Verify that the option and any required device drivers are installed correctly. If these actions do not correct the problem, run the diagnostic programs (see “Diagnostics” on page 49 forinstructions). If you need technical assistance, see “Additional information resources” on page 29. Performance ...

• Clean out your Inbox, Sent Items, and Deleted Items folders from your e-mail application. The folder names and procedures vary depending on your e-mail application. If you need assistance, see thehelp system for your e-mail application. Excessive number of fragmented files Symptom: Excessive numbe...

• If the serial device has its own On/Off switch, make sure it is in the On position. • If the serial device has an Online switch, make sure it is in the Online position. • If the serial device is a printer, make sure paper is loaded correctly. • Verify that any software supplied with the serial dev...

• If the software program used to work correctly, but does not work correctly now, do the following: On the Windows 7 operating system, click Start ➙ Control Panel ➙ System and Security ➙ System ➙ System Protection ➙ System Restore . • If you are unable to resolve the problem through other methods, ...

To run the Lenovo ThinkVantage Toolbox program on the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ System Health and Diagnostics . Follow the instructions on the screen. Follow the instructions on the screen. For additional information, refer to the Lenovo Thi...

• Full Erase Hard Drive Quick Erase Hard Drive provides a DOS utility that performs the following: • Destroys the Master Boot Record (MBR) on the hard drive. • Destroys all copies of the FAT Table on all partitions (both the master and backup). • Destroys the partition table. • Provides messages tha...

Chapter 6. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardlessof which operating system you are using. However, the operating system settings might override any similarsettings in the Setup Utility program. Star...

• Have at least eight characters in length • Contain at least one alphabetic character and one numeric character • Setup Utility program is not case sensitive • Not be your name or your user name • Not be a common word or a common name • Be significantly different from your previous passwords Power-...

• Select ATA Drive Setup to enable or disable an internal or external SATA device. 4. Select the desired settings and press Enter. 5. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program” on page 55. Selecting a startup device If your computer does not...

Chapter 7. Symptom-to-FRU Index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first.Always begin with Chapter 4 “General Checkout” on page 31. This index can also be used to help youdecide which FRUs to have available when servicing a computer. If...

Diagnostic error codes Refer to the following diagnostic error codes when using the diagnostic tests. See “Running tests” on page50 for the specific type for information about the diagnostic programs. In the following index, X can represent any number. Diagnostic Error Code FRU/Action 000-000-XXX BI...

Diagnostic Error Code FRU/Action 305-000-XXX Monitor DDC Test Passed No action 305-250-XXX Monitor DDC self test failure 1. Run the Setup Utility program to enable DDC. 2. Cable 3. Monitor 4. Video card 5. System board 415-000-XXX Modem Test Passed No action 415-XXX-XXX Modem error Remove the Modem ...

Error code POST Error Message Description/Action 0135 Fan failure The system might be overheating. Press F10 to exit. Note: If the problem is caused by the microprocessor fan, press F10 willnot solve the problem. 0211 Keyboard not found When there is no keyboard detected,the error message will be di...

Message/Symptom FRU/Action Program loads from the hard disk with a known-gooddiagnostics diskette in the first 3.5-inch diskette drive 1. Run the Setup Utility program and check Startup sequence. 2. Diskette Drive 3. Diskette Drive Cable 4. System Board 5. Power Supply RPL computer cannot access pro...

Chapter 8. Replacing FRUs This chapter provides removal or replacement procedures for major FRUs. Not all FRUs are documented. Important Before you replace any FRU, read Chapter 2 “Safety information” on page 3. These precautions andguidelines will help you work safely. FRU replacements are to be do...

Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 81 shows the locations of the connectors on the rear of yourcomputer. Some connectors on the rear of your computer are color-coded to help you determine where toconnect the cables on your computer. Figure 2....

FRU locations The following illustration shows the locations of the FRUs. Figure 3. FRU locations 1 System stand hinge cover 15 Internal speaker 2 System stand 16 WI-FI connector 3 Computer cover 17 Power supply 4 System board shield window 18 Rear I/O connector 5 System board shield 19 Internal spe...

System board parts and connectors The following illustration shows the locations of the system board parts and connectors. Figure 4. System board part and connector locations 1 Integrated camera cable connector 9 SATA connector 2 Memory slots (2) 10 Microprocessor fan connector 3 Battery 11 SATA con...

Removing and reinstalling the system stand hinge cover Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge...

6. To reinstall the system stand hinge cover, place the system stand hinge cover on the computer so that the two plastic tabs on the hinge cover align with the corresponding holes in the computer. Figure 6. Reinstalling the system stand hinge cover 7. Reinstall the screw to secure the system stand h...

5. Reinstall the system stand hinge cover. See “Removing and reinstalling the system stand hinge cover” on page 85. Removing and reinstalling the foot stands Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentr...

Figure 11. Loosening the screw that secures the foot stand 7. To reinstall the foot stand, place the foot stand on the computer so that the screw hole aligns with the corresponding hole in the computer, and then tighten the screw to secure the foot stand to the computer. Figure 12. Tightening the sc...

Removing the computer cover Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide ...

Replacing the hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guid...

Figure 16. Removing the hard disk drive 6. Remove the four screws on the hard disk drive bracket, then remove the hard disk drive out of the bracket. Do not touch the circuit board on the bottom of the hard disk drive. Figure 17. Removing the hard disk drive out of the bracket 7. To install the new ...

Replacing the optical drive Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide ...

Figure 19. Installing the optical drive 7. Install the screw 1 to secure the optical drive. Figure 20. Installing the screw to secure the optical drive 8. Go to “Completing the parts replacement” on page 121. Removing the VESA mount bracket Attention Do not open your computer or attempt any repair b...

To remove the VESA mount bracket, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on ...

To replace the rear I/O assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on ...

6. Turn the rear I/O assembly up side down, and then remove the two screws that secure the power cord connector to the power cord connector bracket. Remove the rear I/O assembly from the computer. Figure 23. Removing the power cord connector 7. To reinstall the rear I/O assembly, reinstall the two s...

5. Remove the screw that secures the system board shield, and then slide the system board shield out of the computer. Figure 24. Removing the system board shield 6. To reinstall the system board shield, slide the system board shield into the system board shield slot so that the screw hole aligns wit...

9. Remove the three screws 1 that secure the power supply. Figure 25. Removing the three screws that secure the power supply 10. To reinstall the power supply, reinstall the two screws that secure the power cord connector to the power connector bracket. See “Replacing the rear I/O assembly” on page ...

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of yo...

9. Follow the sequence 1 , 2 , 3 , 4 on the heat sink assembly to tighten the four screws to secure the heat sink assembly to the system board, as shown in Figure 27 “Loosing the four screws that secure the heatsink assembly to the system board” on page 102. 10. Reinstall the system board shield. Se...

Figure 28. Opening the retainer to access the microprocessor 8. Lift the microprocessor straight up and out of the socket. Notes: a. Your microprocessor and socket might look different from the one illustrated. b. Note the orientation of the microprocessor in the socket. You can either look for the ...

Replacing the card reader Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide , ...

10. Reinstall the system board shield. See “Removing and reinstalling the system board shield” on page 98. 11. Go to “Completing the parts replacement” on page 121. Opening the system board shield window Attention Do not open your computer or attempt any repair before reading and understanding the “...

Replacing the battery Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide , go t...

Figure 35. Installing a new battery 8. Reinstall the system board shield or close the system board shield window. See “Removing and reinstalling the system board shield” on page 98 or “Opening the system board shield window” onpage 107. 9. Reinstall the computer cover. See “Completing the parts repl...

7. Disconnect the three cables from the inverter. 8. Lift the inverter off the computer. 9. To reinstall the new inverter, connect the three cables to the new inverter. Position the new inverter and align the two screw holes in the new inverter with those in the computer. 10. Install the two screws ...

3. Remove the computer cover. See “Removing the computer cover” on page 91. 4. Locate the memory slots on the system board. See “FRU locations” on page 82. 5. Remove the system board shield or open the system board shield window to get access to the battery. See “Removing and reinstalling the system...

Replacing the internal speakers Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Gu...

Replacing the integrated camera Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Gu...

10. Route the new integrated camera cable, and then connect the integrated camera cable to the system board. See “System board parts and connectors” on page 84. 11. Reinstall the system board shield. See “Removing and reinstalling the system board shield” on page 98. 12. Go to “Completing the parts ...

Figure 41. Installing one side of the socket cover into the microprocessor socket Note: Your microprocessor socket and cover might look slightly different from the illustration. 4. Carefully press the other side of the socket cover downwards until the socket cover snaps into place. 5. Carefully chec...

Figure 42. Removing the foot stands 5. Locate the LCD panel in the computer. See “FRU locations” on page 82. 6. Remove the optical drive. See “Replacing the optical drive” on page 94. 7. Remove the inverter. See “Replacing the inverter” on page 109. 8. Remove the rear I/O assembly. See “Replacing th...

11. Remove all the 15 screws that secure the computer main bracket to the front bezel. Figure 44. Removing all the 15 screws that secure the computer main bracket to the front bezel 12. Note the locations of all cable connections that prevent you from lifting the computer main bracket, and disconnec...

Figure 46. Reinstalling all the 15 screws that secure the computer main bracket to the front bezel 19. Reconnect the LCD panel cable to the system board. See Figure 47. Reconnect the LCD panel cable to the system board 20. Reinstall the integrated camera. See “Replacing the integrated camera” on pag...

Replacing the WI-FI card Attention Do not open your computer or attempt any repair before reading and understanding the “Important safetyinformation” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide , go to: http...

Figure 49. Removing the WI-FI card 9. Insert the notched end of the new WI-FI card into the mini PCI Express slot. Press the new WI-FI card firmly, and then pivot the WI-FI card to align the screw hole in the new WI-FI card with thatin the system board. 10. Install the screw to secure the new WI-FI ...

3. Lower and position the computer cover into place and then tighten the two screws 1 to secure the computer cover. Figure 50. Installing the computer cover 4. Reinstall the system stand and system stand hinge cover. See “Removing and reinstalling the system stand” on page 86 and “Removing and reins...

Item # FRUs FRU # CRU 24 LCD panel, 20inch 1600x900 CCFL panel • MT 5068: all models • MT 7558: all models • MT 7567: all models 03T6429 N 24 LCD panel, 20inch 1600x900 CCFL panel • MT 5068: all models • MT 7558: all models • MT 7567: all models 03T6431 N 25 Inverter • MT 5068: all models • MT 7558:...

FRUs FRU # CRU FRU, assembly panel bracket • MT 5068: all models • MT 7558: all models • MT 7567: all models 03T9681 N FRU, screw kits • MT 5068: all models • MT 7558: all models • MT 7567: all models 03T9684 N Adapters and miscellaneous FRUs Adapters and miscellaneous FRUs FRU # CRU Intel-1000 wire...

Keyboard (Preferred professional fullsize USB) FRU # CRU Preferred Pro Fullsize USB--Lithuanian • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO 45J4896 1 Preferred Pro Fullsize USB--India • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO 54Y8381 1 Mice FRU # CRU Lenovo enhanced optical USB mouse • MT 5068: ...

Chapter 10. Additional Service Information This chapter provides additional information that the service representative might find helpful. Security features Security features in this section include the following: • Passwords • Vital Product Data • Management Information Format (MIF) Hardware contr...

Note: You can download a self-starting bootable disc image (known as an ISO image) with the system program updates to create a system-program-update disc. Go to:http://www.lenovo.com/support To update (flash) the BIOS from a disc, do the following: 1. Turn off your computer. 2. Repeatedly press and ...

4. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin 3). 5. Install the computer cover and reconnect all cables and power cords that were disconnected. See “Completing the parts replacement” on page 121. 6. Repeatedly press and release the F12 ke...

Index A Administrator, password 54 B basic troubleshooting 33 battery, replacing 108 boot-block recovery 152 C card reader, replacing 106 changing password 54 startup device sequence 55 computer cover removing 91 computer cover, reinstalling 121 connectors rear 81 connectors, controls, indicators fr...